- In support of HMsec, allow the count command in countsec to run without a
preset parameter. If this is missing the old, stored preset is used.
- Removed a check which causes initialisation of the HM from a batch file fail
for POLDI
- fixed @nl@ encoding of \n problem with certain kinds of batch files generated by GTSE
- Fixed a bug with summing on hitsmemsec. nxdataset now uses 64 bit int for dimensions.
- Fixed motorsec to remove itself properly from a parent when linked. Please note
that there is still the limitation that a second generation motor can only be linked
once in a Hipadaba tree
- Extended subsampling a HM for second generation HM
- Added a hscriptnotify. This calls a script on the update of a node
- POLDI has been rebuilt, chnages to data file writing
- For testing, sinqhttopt now understands a special command, byteswapoff,
which switches off byte swapping. Required when the HM ius run on an Intel box.
SKIPPED:
psi/polterwrite.c
psi/sinqhttpopt.c
- Added missing cnvrt files, stolen from Markus
- Debugged the new sinqhttpopt driver for SINQ HTTP HM
- Debugged the driver for the new S7 Siemens SPS
- Added handling of hexadecimal terminators to ascon.c
- Increased the write buffer size in asynnet again
- Fixed a core dump in lld.c
- Added writing of second gen HM to nxscript.c
- Added doubletime command to SICS
- Fixed a core dump issue in sicshdbadapter.c on dimension changes
- Modified sicsobj to look for lower case keys too
SKIPPED:
psi/cnvrt.c
psi/cnvrt.h
psi/el734hp.c
psi/make_gen
psi/sinqhttpopt.c
psi/sinqhttpprot.c
psi/spss7.c
psi/swmotor.c
- Added a warning for excessive data rates on monitors
- Added statistics to devser and thus to scriptcontext
- Added byte concatenation to dynstring
- Added aborting for reflection generation to fourmess.c
- Added data checksum testing to hipadaba, use for update tests
- Fixed interrupt discovery in network.c, caused invalid interrupt
codes which in turn confused sicscron which had to be fixed too.
- Renamed ubcalc into ubcalcint in order to reclaim the ubcalc for Jurg
- Added an a3offset to tasub in order to fix what I perceive an IS problem
- Added support for the newer version of the Siemens SPS, the S7
- Added a not yet fully working sinqhttpopt driver which talks to
http HM without libghttp
SKIPPED:
psi/delcam.c
psi/make_gen
psi/psi.c
psi/sinq.c
psi/sinq.h
psi/sinqhttpopt.c
psi/slsvme.c
psi/spss7.c
drivable. Required a new event in devexec.c
- Fixed the phytron driver to handle speed well
- Added a protocol driver for the TCP/IP bridge to the SLS magnets
SKIPPED:
psi/make_gen
psi/phytron.c
psi/psi.c
psi/slsecho.c
psi/sps.c
to fourmess
- Fixed hdbtable, reflist and tasub up to work with GTSE
- Made TRICS do fast scans again
- Added support for SANS beam center calculations
- Fixed a bug where SICS apparently did double counting but in fact
just omitted an error message and did not
- Added the harray command
- Implemented the desired run/drive behaviour: drive waits for what it started
run starts, and success waits for everything to finish. This required
changes to a lot of files.
- Fixed a bug in remob which supressed required messages
- Added a drivable adapter to scriptcontext nodes
- Added subsampling to simulated histograms (and as a general option) in
order to support Gumtree testing.
- Extended the Hdb adapter to support SICSdata
- Made the simulated histogram memory driver work properly when
data has been set.
- Implemented the hfactory command
- Removed hdbcommand which was never finsihed
- Added new ACT protocol
- Extended sicshdbadapter to cover counters and status to put the status
into Hipadaba
- Fixes to napi5.c
- Exe now supports hdbrun which allows to write output for a buffer into
hdb node.
