forked from epics_driver_modules/motorBase
Ron Sluiter
254 lines
7.6 KiB
Plaintext
254 lines
7.6 KiB
Plaintext
# The is the ASYN example for communication to a Newport MM4000/5/6.
|
|
# "#!" marks lines that can be uncommented.
|
|
|
|
< envPaths
|
|
|
|
dbLoadDatabase("$(TOP)/dbd/WithAsyn.dbd")
|
|
WithAsyn_registerRecordDeviceDriver(pdbbase)
|
|
dbLoadTemplate("motor.substitutions")
|
|
dbLoadRecords("$(MOTOR)/db/motorUtil.db", "P=IOC:")
|
|
|
|
|
|
# The following commands are for a local serial line
|
|
# Configure the asyn server code for either sun or linux.
|
|
#!Sun Solaris !drvAsynSerialPortConfigure("L0","/dev/ttya" ,0,0,0)
|
|
#!Redhat Linux!drvAsynSerialPortConfigure("L0","/dev/ttyS0",0,0,0)
|
|
|
|
asynSetOption("L0", -1, "baud", "9600")
|
|
asynSetOption("L0", -1, "bits", "8")
|
|
asynSetOption("L0", -1, "parity", "none")
|
|
asynSetOption("L0", -1, "stop", "1")
|
|
asynSetOption("L0", -1, "clocal", "Y")
|
|
asynSetOption("L0", -1, "crtscts", "N")
|
|
|
|
|
|
# Newport MM3000 and MM4000/5/6 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!MM3000Setup(1, 10)
|
|
MM4000Setup(1, 10)
|
|
|
|
# Newport MM3000 and MM4000/5/6 driver configuration parameters:
|
|
# (1) controller# being configured
|
|
# (2) ASYN port name
|
|
# (3) address (GPIB only)
|
|
#!MM3000Config(0, "a-Serial[0]")
|
|
#!drvMM3000debug=4
|
|
MM4000Config(0, "L0")
|
|
#!var drvMM4000debug 4
|
|
|
|
# The MM4000 driver does not set end of string (EOS).
|
|
# for RS232 serial,
|
|
#!asynOctetSetInputEos( "a-Serial[0]",0,"\r")
|
|
#!asynOctetSetOutputEos("a-Serial[0]",0,"\r")
|
|
# for GPIB,
|
|
#!asynInterposeEosConfig("L0", 10, 1, 1)
|
|
#!asynOctetSetInputEos( "L0",10,"\r")
|
|
#!asynOctetSetOutputEos("L0",10,"\r")
|
|
|
|
# Newport PM500 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!PM500Setup(1, 10)
|
|
|
|
# Newport PM500 configuration parameters:
|
|
# (1) controller# being configured,
|
|
# (2) ASYN port name
|
|
# (3) address (GPIB only)
|
|
#!PM500Config(0, "L0")
|
|
#!var drvPM500debug 4
|
|
|
|
# IMS IM483 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
# SM - single mode PL - party mode
|
|
#!IM483SMSetup(1, 10)
|
|
#!IM483PLSetup(1, 10)
|
|
|
|
# IMS IM483 configuration parameters:
|
|
# (1) controller# (chain#) being configured,
|
|
# (2) ASYN port name
|
|
# SM - single mode PL - party mode
|
|
#!IM483SMConfig(0, "L0")
|
|
#!var drvIM483SMdebug 4
|
|
#!IM483PLConfig(0, "L0")
|
|
#!var drvIM483PLdebug 4
|
|
|
|
# MCB-4B driver setup parameters:
|
|
# (1) maximum # of controllers,
|
|
# (2) motor task polling rate (min=1Hz, max=60Hz)
|
|
#!MCB4BSetup(1, 10)
|
|
|
|
# MCB-4B driver configuration parameters:
|
|
# (1) controller
|
|
# (2) ASYN port name
|
|
#!MCB4BConfig(0, "L0")
|
|
#!asynOctetSetInputEos("L0",0,"\r")
|
|
#!asynOctetSetOutputEos("L0",0,"\r")
|
|
#!var drvMCB4BDebug 4
|
|
|
|
# Newport ESP300 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!ESP300Setup(1, 10)
|
|
|
|
# Newport ESP300 driver configuration parameters:
|
|
# (1) controller# being configured,
|
|
# (2) ASYN port name
|
|
# (3) address (GPIB only)
|
|
#!ESP300Config(0, "L0")
|
|
#!var drvESP300debug 4
|
|
|
|
# MicroMo MVP2001 driver setup parameters:
|
|
#
|
|
# NOTE: The 1st controller on each chain should have it's address = 1.
|
|
# The rest of the controllers on a chain should follow sequentially.
|
|
#
|
|
#
|
|
# int MVP2001Setup(int num_cards, /* number of CHAINS of controllers */
|
|
# int scan_rate) /* polling rate (Min=1Hz, max=60Hz) */
|
|
#!MVP2001Setup(1, 10)
|
|
|
|
# int MVP2001Config(int card, /* CHAIN being configured */
|
|
# (2) ASYN port name
|
|
#!MVP2001Config(0, "L0")
|
|
#!drvMVP2001debug=4
|
|
|
|
# PI C-844 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!PIC844Setup(1, 10)
|
|
|
|
# PI C-844 driver configuration parameters:
|
|
# (1) controller# being configured,
|
|
# (2) ASYN port name
|
|
# (3) address (GPIB only)
|
|
#!PIC844Config(0, "L0")
|
|
#!var drvPIC844debug 4
|
|
|
|
# PI C-848 driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!PIC848Setup(1, 2)
|
|
|
|
# PI C-848 driver configuration parameters:
|
|
# (1) controller# being configured,
|
|
# (2) ASYN port name
|
|
#!PIC848Config(0, "L0")
|
|
#!drvPIC848debug = 4
|
|
|
|
# Micos MoCo driver setup parameters:
|
|
# Load MicosSetup once.
|
|
# (1) max # of controller groups. Controller groups are per serial
|
|
# port.
|
|
# (2) max # axes per controller group. Maximum 16. (addr 0-15)
|
|
# (3) motor task polling rate (min=1Hz, max=60Hz, 10Hz works well)
|
|
# Example:
|
|
# MicosSetup(1, 2, 10) 1 group. 2 axes (controllers) in the group.
|
|
# 10Hz poll.
|
|
#!MicosSetup(1, 2, 10)
|
|
|
|
# Micos MoCo driver configuration parameters:
|
|
# Load one MicosConfig for each group of Micos drivers.
|
|
# (1) "Controller group" number
|
|
# (2) ASYN port name
|
|
#!MicosConfig(0, "L0")
|
|
#!var drvMicosDebug 4
|
|
|
|
# IMS MDrive driver setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!MDriveSetup(1, 10)
|
|
|
|
# IMS MDrive driver configuration parameters:
|
|
# (1) controller# being configured,
|
|
# (2) ASYN port name
|
|
#!MDriveConfig(0, "L0")
|
|
#!var drvMDrivedebug 4
|
|
|
|
# Kohzu SC-800 motor controller setup parameters:
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!SC800Setup(1, 5)
|
|
|
|
# Kohzu SC-800 motor controller configuration parameters:
|
|
# (1) controller# being configured
|
|
# (2) ASYN port name
|
|
# (3) address (GPIB only)
|
|
#!SC800Config(0, "L0", 0)
|
|
#!var drvSC800debug 4
|
|
|
|
# Faulhaber MCDC2805 driver setup parameters:
|
|
# (1)Max. controller count
|
|
# (2)Polling rate
|
|
#!MCDC2805Setup(1, 10)
|
|
|
|
# Faulhaber MCDC2805 driver configuration parameters:
|
|
# (1)Card being configured
|
|
# (2)# modules on this serial port
|
|
# (3)asyn port name
|
|
#!MCDC2805Config(0, 1, "L0")
|
|
#!var drvMCDC2805debug 4
|
|
|
|
# The MCDC2805 driver does not set end of string (EOS).
|
|
#!asynOctetSetInputEos("L0",0,"\r")
|
|
#!asynOctetSetOutputEos("L0",0,"\r")
|
|
|
|
|
|
# attocube ANC 150 asyn motor driver setup parameter.
|
|
#!ANC150AsynSetup(1) /* number of ANC150 controllers in system. */
|
|
|
|
# attocube ANC 150 asyn motor driver configure parameters.
|
|
# (1) Controller number being configured
|
|
# (2) ASYN port name
|
|
# (3) Number of axes this controller supports
|
|
# (4) Time to poll (msec) when an axis is in motion
|
|
# (5) Time to poll (msec) when an axis is idle. 0 for no polling
|
|
#!ANC150AsynConfig(0, "a-Serial[1]", 3, 250, 2000)
|
|
|
|
|
|
# Aerotech Ensemble digital servo controller Setup
|
|
# (1) maximum number of controllers in system
|
|
# (2) motor task polling rate (min=1Hz,max=60Hz)
|
|
#!EnsembleSetup(1, 10)
|
|
|
|
# Aerotech Ensemble digital servo controller Configure
|
|
# (1) controller# being configured,
|
|
# (2) asyn port name (string)
|
|
#!EnsembleConfig(0, "a-Serial[0]")
|
|
|
|
|
|
# Newport MM4000/5/6 asyn motor driver setup parameter.
|
|
#!MM4000AsynSetup(1) /* number of MM4000 controllers in system. */
|
|
|
|
# Newport MM4000/5/6 asyn motor driver configure parameters.
|
|
# (1) Controller number being configured
|
|
# (2) ASYN port name
|
|
# (3) ASYN address (GPIB only)
|
|
# (4) Number of axes this controller supports
|
|
# (5) Time to poll (msec) when an axis is in motion
|
|
# (6) Time to poll (msec) when an axis is idle. 0 for no polling
|
|
#!MM4000AsynConfig(0, "a-Serial[1]", 0, 1, 100, 250)
|
|
|
|
# Asyn-based Motor Record support
|
|
# (1) Asyn port
|
|
# (2) Driver name
|
|
# (3) Controller index
|
|
# (4) Max. number of axes
|
|
#!drvAsynMotorConfigure("ANC150","motorANC150",0,1)
|
|
|
|
|
|
# Asyn-based Motor Record support
|
|
# (1) Asyn port
|
|
# (2) Driver name
|
|
# (3) Controller index
|
|
# (4) Max. number of axes
|
|
#!drvAsynMotorConfigure("ANC150","motorANC150",0,1)
|
|
|
|
|
|
iocInit
|
|
|
|
# motorUtil (allstop & alldone)
|
|
motorUtilInit("IOC:")
|
|
|