R3.14.x conversion from 'config' to 'configure' directory.

2002-09-13 20:26:05 +00:00
parent 449ff6672e
commit 44b2fd2f90
9 changed files with 94 additions and 0 deletions
@@ -0,0 +1,13 @@
+#CONFIG
+include $(TOP)/configure/CONFIG_APP
+# Add any changes to make definitions here
+
+#CROSS_COMPILER_TARGET_ARCHS = vxWorks-68040
+
+# Use this when your IOC and the host use different paths
+# to access the application. Typically this will be 
+# used with the Microsoft FTP server or with NFS mounts. Use
+# is indicated by failure of the cdCommands script on
+# vxWorks. You must rebuild in the iocBoot directory 
+# before this takes effect.
+#IOCS_APPL_TOP = <the top of the application as seen by the IOC>
@@ -0,0 +1,17 @@
+# CONFIG_APP
+
+include $(TOP)/configure/RELEASE
+-include $(TOP)/configure/RELEASE.$(EPICS_HOST_ARCH)
+CONFIG=$(EPICS_BASE)/configure
+include $(CONFIG)/CONFIG
+INSTALL_LOCATION = $(TOP)
+ifdef INSTALL_LOCATION_APP
+INSTALL_LOCATION = $(INSTALL_LOCATION_APP)
+endif
+
+ifdef T_A
+-include $(TOP)/configure/O.$(T_A)/CONFIG_APP_INCLUDE
+endif
+
+# dbst based database optimization (default: NO)
+DB_OPT = NO
@@ -0,0 +1,15 @@
+# Makefile
+
+TOP=..
+
+include $(TOP)/configure/CONFIG
+
+# Set the following to NO to disable consistency checking of
+# the support applications defined in $(TOP)/configure/RELEASE
+CHECK_RELEASE = YES
+
+TARGETS = $(CONFIG_TARGETS)
+CONFIGS += $(subst ../,,$(wildcard $(CONFIG_INSTALLS)))
+
+include $(TOP)/configure/RULES
+
@@ -0,0 +1,33 @@
+# RELEASE - Location of external products
+#
+# Note: This file will be scanned to automatically generate
+#       include path definitions etc.
+#       The order of the following declarations will be retained
+#       within those definitions.
+#
+# Add your declarations here
+
+#SUPPORT=
+
+# Define the following if MPF is defined (i.e., if either serial
+# or GPIB motor controller support is required).
+#MPF_SERIAL=$(SUPPORT)/mpfSerial/mpfSerial1-3
+
+# If the EPICS GPIB Module from Benjamin Franksen is used, then remove the '#'
+# from the following and modify the motorApp/CommSrc/Makefile.Vx file per
+# instructions found there.  If GPIB driver support is from EPICS base, then
+# leave this line commented out.
+#GPIB=$(SUPPORT)/gpib
+
+# If any motor controller communication mechanism besides the VME backplane is
+# required, then MPF must be defined.
+#MPF=$(SUPPORT)/mpf/mpf1-8
+
+#EPICS_BASE=$(SUPPORT)/../base
+
+# The following must be defined if motorExApp is to be built.
+TEMPLATE_TOP=$(EPICS_BASE)/templates/makeBaseApp/top
+
+# The following must be defined if the "WithMPF" example in motorExApp is to
+# be built.
+#MPF_GPIB=$(SUPPORT)/mpfGpib/mpfGpib1-4
@@ -0,0 +1,5 @@
+#CONFIG
+include $(EPICS_BASE)/configure/RULES
+
+# Library should be rebuilt because LIBOBJS may have changed.
+$(LIBNAME): ../Makefile
@@ -0,0 +1,2 @@
+#RULES.ioc
+include $(EPICS_BASE)/configure/RULES.ioc
@@ -0,0 +1,4 @@
+#RULES.iocBoot
+DIRS += $(wildcard ioc*)
+DIRS += $(wildcard as*)
+include $(EPICS_BASE)/configure/RULES_DIRS
@@ -0,0 +1,2 @@
+#RULES_DIRS
+include $(EPICS_BASE)/configure/RULES_DIRS
@@ -0,0 +1,3 @@
+#RULES_TOP
+include $(EPICS_BASE)/configure/RULES_TOP
+