Two CPU's not supported under ASYN.

iocBoot/iocipServer/Makefile

@@ -1,8 +0,0 @@
-TOP = ../..
-include $(TOP)/configure/CONFIG
-#ARCH = solaris-sparc-gnu
-ARCH = vxWorks-68060
-#ARCH = vxWorks-ppc604
-TARGETS = cdCommands
-include $(TOP)/configure/RULES.ioc
-

iocBoot/iocipServer/st.cmd

@@ -1,69 +0,0 @@
-# This configures the MPF server stuff.  GPIB support is commented out, but can
-# be added by simply deleting the "# !GPIB! #" comments.
-
-#The following must be added for many board support packages
-#cd "... IOC st.cmd complete directory path ... "
-
-< cdCommands
-< ../MPFconfig.cmd
- 
-cd appbin
-ld < mpfLib
-ld < ipLib
-ld < mpfserialserverLib
-# !GPIB! #ld < mpfgpibserverLib
-
-cd startup
-
-#start message router
-routerInit
-# 3rd argument is VxWorks "inet on backplane" boot parameter.
-tcpMessageRouterServerStart(MPF_Remote_Server,9900,Remote_IP,1500,40)
-
-###############################################################################
-# Initialize IP carrier
-# ipacAddCarrier(ipac_carrier_t *pcarrier, char *cardParams)
-#   pcarrier   - pointer to carrier driver structure
-#   cardParams - carrier-specific init parameters
-
-carrier = "ipac"
-ipacAddCarrier(&ipmv162, "A:l=3,3 m=0xe0000000,64;B:l=3,3 m=0xe0010000,64;C:l=3,3 m=0xe0020000,64;D:l=3,3 m=0xe0030000,64")
-initIpacCarrier(carrier, 0)
-
-###############################################################################
-# Initialize GPIB module
-
-# !GPIB! #initGpibGsTi9914("GS-IP488-0",carrier,"IP_d",104)
-# !GPIB! #initGpibServer("GPIB0","GS-IP488-0",1024,1000)
-
-###############################################################################
-# Initialize Octal UART module
-#initOctalUART("moduleName","carrierName","carrierSite",nports,intVec)
-initOctalUART("octalUart0",carrier,"IP_a",8,100)
-
-# initOctalUARTPort(char* portName,char* moduleName,int port,int baud,
-#                   char* parity,int stop_bits,int bits_char,char* flow_control)
-# 'baud' is the baud rate. 1200, 2400, 4800, 9600, 19200, 38400
-# 'parity' is "E" for even, "O" for odd, "N" for none.
-# 'bits_per_character' = {5,6,7,8}
-# 'stop_bits' = {1,2}
-# 'flow_control' is "N" for none, "H" for hardware
-# Port 0 is Generic Serial Record
-
-initOctalUARTPort("UART[0]","octalUart0",0, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[1]","octalUart0",1, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[2]","octalUart0",2, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[3]","octalUart0",3, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[4]","octalUart0",4, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[5]","octalUart0",5, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[6]","octalUart0",6, 9600,"N",1,8,"N")
-initOctalUARTPort("UART[7]","octalUart0",7, 9600,"N",1,8,"N")
-
-initSerialServer("a-Serial[0]","UART[0]",1000,20,"\r",1)
-initSerialServer("a-Serial[1]","UART[1]",1000,20,"\r",1)
-initSerialServer("a-Serial[2]","UART[2]",1000,20,"\r",1)
-initSerialServer("a-Serial[3]","UART[3]",1000,20,"\r",1)
-initSerialServer("a-Serial[4]","UART[4]",1000,20,"\r",1)
-initSerialServer("a-Serial[5]","UART[5]",1000,20,"\r",1)
-initSerialServer("a-Serial[6]","UART[6]",1000,20,"\r",1)
-initSerialServer("a-Serial[7]","UART[7]",1000,20,"\r",1)