* jf: if bit 14 in reg 0x5d (electron mode collection bit) is changed, configure chip if v1.1 and powered on. so touch writeregister (setbit/clearbit also calls write register in the end). replace when electroncollectionmode command introduced
* jf: if bit 14 in reg 0x5d (electron mode collection bit) is changed, configure chip if v1.1 and powered on. so touch writeregister (setbit/clearbit also calls write register in the end). replace when electroncollectionmode command introduced
* jf: rewrite of status reg bits, waiting state includes both wati for trigger and start frame, blocking trigger only waits if its not in waiting for trigger and run busy enabled, error state connected in firmware
* rewrite of status reg bits, waiting state includes both wati for trigger and start frame, blocking trigger only waits if its not in waiting for trigger and run busy enabled, error state connected in firmware
* jf sync mode master could return idle when stopped and so not all modules return the same value and must check for 'stopped or idle', Also must throw if any of the module gives an error
* added contains_only to sls::Result (#827)
* added variadic template for checking if a result contains only specified values
* fix for gcc4.8
* renamed to Result::contains_only
* updated condition in Detector.cpp
* stop on only the positions
---------
Co-authored-by: Erik Fröjdh <erik.frojdh@gmail.com>
* jf sync mode master could return idle when stopped and so not all modules return the same value and must check for 'stopped or idle', Also must throw if any of the module gives an error
* added contains_only to sls::Result (#827)
* added variadic template for checking if a result contains only specified values
* fix for gcc4.8
* renamed to Result::contains_only
* stop on only the positions
---------
Co-authored-by: Erik Fröjdh <erik.frojdh@gmail.com>
* jf sync mode master could return idle when stopped and so not all modules return the same value and must check for 'stopped or idle', Also must throw if any of the module gives an error ( not jungfrau, but eiger could)
* added contains_only to sls::Result (#827)
* added variadic template for checking if a result contains only specified values
* fix for gcc4.8
* renamed to Result::contains_only
* stop on only the positions
---------
Co-authored-by: Erik Fröjdh <erik.frojdh@gmail.com>
* getVoltageList, getVoltage /set, getMeasuredVoltage, getVoltageNames /set, getVoltageIndex moved to 'Power' as its misleading
* added cstdint and names slowadc, added division to mV
* changed uV to mV in command line slow adc help. removed all python slowadcs (as it was already implemented as slowadc
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
* updated python bindings for port update from int to uint16_t
* user friendly error message for exception when python arg does not match uint16_t for ports
* merge fix from 7.0.2: new jungfrau fw versions, incremented binary, hdf5 and json versions
* moench: changed dac names and default values to old moench values
* moench: remove interface clk polarity at start up
* moench: default speed is half speed, default values for adc offset and adc phase for different speeds (only half speed confirmed), adc vref voltage to 2.0 like G1
* moench: connected adc pipeline to client
* moench: receiver- default frames per file is 100k and discard partial frames as default
* moench binary in
* using tostring in gui for dacs
* moved frame discard policy as a parameter to be configured with a default depending on detector
* moench: 300 degrees for adc phase in full speed
* silence warnings
* making constructors explicit to avoid unintended conversions
* changed struct to class since we already have public:
---------
Co-authored-by: Dhanya Thattil <dhanya.thattil@psi.ch>
