* period and exptime(patternwaittime level 0)
* added new regsieterdefs and updated api version and fixedpattern reg
* autogenerate commands
* formatting
* minor
* wip resetflow, readout mode, transceiver mask, transceiver enable
* acquisition, but streaming done bit and busy (exposing + read chip to fifo) not known yet from fw
* programming fpga and device tree done
* most configuration done, need to connect configuretransceiver to client
* stuck at resetting transciever timed out
* minor
* fixed virtual, added chip busyto fifo, streaming busy, set/getnext framenumber
* configuretransceiver from client, added help in client
* make formatt and command generation
* tests for xilinx ctb works
* command generation
* dacs added and tested, power not done
* power added
* added temp_fpga
* binaries in
* ctrlreg is 0 to enable chip=fixed, high dac val = min val= fixed, power regulators in weird order=fixed, device tree could be loaded with dacs before adcs=fixed
* start works
* virtual server sends
* receiver works
* tests
* python function and enum generation, commands generatorn and autocomplete, formatting, tests
* tests fail at start(transceiver not aligned)
* tests passed
* all binaries compiled
* eiger binary in
* added --nomodule cehck for xilinx
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* connected kernelversion, hardwareversion, versions, framesl, triggersl, dr, timingmode, pattern (except patioctrl) thats there for altera ctb
* replaced set/get64Bit to set/getU64bit in all loadpattern.c for (ctb and m3 also)
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* allowing tests for xilinx
* binaries in
* updated registers, arm64
* compiler set to aarch64 for xilinx server
* updated RegisterDefs.h
* merge into generate branch and resolving conflicts and adding the xilinx changes to callerspecial and commands.yaml
* compiles and can print firmware version (using a different csp0 address)
* fixing other servers (gotthard, jungfrau, moench, mythen3) that it returns in case of mapping failure, xilinxctb: added that it checks type, prints proper fw version, checks kernel date, added armprocessor define to use in common places, added specifiers to supress overflow and truncation warnings
* added detector ip and mac adddress to the printout
* fixed tests and recompiled servers
* draft to fix virtual test when it fails
* catching errors in tests and removing sigchild ignore so servers (process in background) executing commands will not fail (pclose no child processes, if sigchld is ignored) fixed
* uncommented python loading config
* somehow killal slsReciever in second detector test fails even though no receiver running
* fixing script for virtual simlator test:fixed issue with check if process running, fixed moench tests
* jf: if bit 14 in reg 0x5d (electron mode collection bit) is changed, configure chip if v1.1 and powered on. so touch writeregister (setbit/clearbit also calls write register in the end). replace when electroncollectionmode command introduced
* merge fix from 7.0.2: new jungfrau fw versions, incremented binary, hdf5 and json versions
* moench: changed dac names and default values to old moench values
* moench: remove interface clk polarity at start up
* moench: default speed is half speed, default values for adc offset and adc phase for different speeds (only half speed confirmed), adc vref voltage to 2.0 like G1
* moench: connected adc pipeline to client
* moench: receiver- default frames per file is 100k and discard partial frames as default
* moench binary in
* using tostring in gui for dacs
* moved frame discard policy as a parameter to be configured with a default depending on detector
* moench: 300 degrees for adc phase in full speed
* transceiverenable, tsamples, romode for tranceiver and digital_transceiver
* 202 spec instr only for transceiver mode
* removed check for empty in trans readout and clean memory before reading from fifo
* ctb read fifo strobe for all after reading all channels, adding 1us after selecting channel, changing fw date
* updated 10gb transceiver enable
----
* added transceiver (tsamples, romode(transceiver, digital_transceiver), transceiverenable (mask)
* clean memory before reading from fifo (for analog and digital as well)
* read fifo then read strobe (also corresp fw) fixes number of reads (also for analg and digital)-> increases all pipelines by 1
* fixed bug in rearranging digital data in receiver
* fixed bug in streaming size of data after rearranging
* fixed bug in setbit, clearbit,and getbit
* status checks fifo before returning idle (transmitting if data in fifo if transceiver more enabled)
* soem matterhorn specifics that will need to be put into pattern in a month or two. this is temporary.
* NOTE: breaking api. rxParameters struct has transceiverenabel and tsamples given from det to receiver
* when dbit list is enabled, the size of data in zmq stream is changed to only the digital bits enabled size. now fixed to also include analog size
* allowing to set 0xffffffffffffffff to pat io control. prevously was used to do a get. fixed also for pat bit mask and pat mask
* moench, removed chip version, filter resistor, filter cells, currentsoures, gain mode, setttings(modes), dbitphase, maxdbitphase, autocompdisable, comparatordisabletime, made acq start and stop a pulse, removed unused registers
* added parallel command
* remove gain plot for moench
* moench: updated adc invert val
* moench: update adcoffset to 0xf and adcphase to 140 degrees
* removed sync clock in moench
* updated min fw version
* removing config file in moench server
* Revert "Ctb: allow adc mask enable to be 0 for 1 and 10GbE (#750)"
This reverts commit a0f250a4876937ebb2a96c8948fdea380625a86e.
* better error message about setting adc mask to 0. Cannot set it to 0 due to ram allocation
Firmware updated. spi moved to firmware. In Software, configuring, then a pulse to start, wait for done bit and convert the values read from a regiter.
* eiger: hardwareversion, fix firmware version unable to read version scenarios, check to see if febl, febr and beb have same fw version
* feb versions can be picked up only after feb initialization
* copied jungfrau server to moench and adapted
* fixed image size and num packets
* read n rows allows 16
* commneted out configure_asic_timer at server startup. To be removed later the ASIC_CTRL_REG and storage cell options
* moench:removing the decrement (which was in jf) in read n rows to register
* removed lblsamples from gui
