* period and exptime(patternwaittime level 0)
* added new regsieterdefs and updated api version and fixedpattern reg
* autogenerate commands
* formatting
* minor
* wip resetflow, readout mode, transceiver mask, transceiver enable
* acquisition, but streaming done bit and busy (exposing + read chip to fifo) not known yet from fw
* programming fpga and device tree done
* most configuration done, need to connect configuretransceiver to client
* stuck at resetting transciever timed out
* minor
* fixed virtual, added chip busyto fifo, streaming busy, set/getnext framenumber
* configuretransceiver from client, added help in client
* make formatt and command generation
* tests for xilinx ctb works
* command generation
* dacs added and tested, power not done
* power added
* added temp_fpga
* binaries in
* ctrlreg is 0 to enable chip=fixed, high dac val = min val= fixed, power regulators in weird order=fixed, device tree could be loaded with dacs before adcs=fixed
* start works
* virtual server sends
* receiver works
* tests
* python function and enum generation, commands generatorn and autocomplete, formatting, tests
* tests fail at start(transceiver not aligned)
* tests passed
* all binaries compiled
* eiger binary in
* added --nomodule cehck for xilinx
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* connected kernelversion, hardwareversion, versions, framesl, triggersl, dr, timingmode, pattern (except patioctrl) thats there for altera ctb
* replaced set/get64Bit to set/getU64bit in all loadpattern.c for (ctb and m3 also)
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* allowing tests for xilinx
* binaries in
* updated registers, arm64
* compiler set to aarch64 for xilinx server
* updated RegisterDefs.h
* merge into generate branch and resolving conflicts and adding the xilinx changes to callerspecial and commands.yaml
* compiles and can print firmware version (using a different csp0 address)
* fixing other servers (gotthard, jungfrau, moench, mythen3) that it returns in case of mapping failure, xilinxctb: added that it checks type, prints proper fw version, checks kernel date, added armprocessor define to use in common places, added specifiers to supress overflow and truncation warnings
* added detector ip and mac adddress to the printout
* fixed tests and recompiled servers
* draft to fix virtual test when it fails
* catching errors in tests and removing sigchild ignore so servers (process in background) executing commands will not fail (pclose no child processes, if sigchld is ignored) fixed
* uncommented python loading config
* somehow killal slsReciever in second detector test fails even though no receiver running
* fixing script for virtual simlator test:fixed issue with check if process running, fixed moench tests
* jf: if bit 14 in reg 0x5d (electron mode collection bit) is changed, configure chip if v1.1 and powered on. so touch writeregister (setbit/clearbit also calls write register in the end). replace when electroncollectionmode command introduced
* jf: rewrite of status reg bits, waiting state includes both wati for trigger and start frame, blocking trigger only waits if its not in waiting for trigger and run busy enabled, error state connected in firmware
* merge fix from 7.0.2: new jungfrau fw versions, incremented binary, hdf5 and json versions
* moench: changed dac names and default values to old moench values
* moench: remove interface clk polarity at start up
* moench: default speed is half speed, default values for adc offset and adc phase for different speeds (only half speed confirmed), adc vref voltage to 2.0 like G1
* moench: connected adc pipeline to client
* moench: receiver- default frames per file is 100k and discard partial frames as default
* moench binary in
* using tostring in gui for dacs
* moved frame discard policy as a parameter to be configured with a default depending on detector
* moench: 300 degrees for adc phase in full speed
* when dbit list is enabled, the size of data in zmq stream is changed to only the digital bits enabled size. now fixed to also include analog size
* allowing to set 0xffffffffffffffff to pat io control. prevously was used to do a get. fixed also for pat bit mask and pat mask
- start acq list: mixup with master pos #743 : fix that only master starts second and not all (for start acq), typo with pos and masters list
- synced master status running when setting to slave #747: synced master status running when setting to slave
* moench, removed chip version, filter resistor, filter cells, currentsoures, gain mode, setttings(modes), dbitphase, maxdbitphase, autocompdisable, comparatordisabletime, made acq start and stop a pulse, removed unused registers
* added parallel command
* remove gain plot for moench
* moench: updated adc invert val
* moench: update adcoffset to 0xf and adcphase to 140 degrees
* removed sync clock in moench
* updated min fw version
* removing config file in moench server
* merge fix from #721 PR (sync) 7.0.2.rc -> developer
* row and column for jungfrau mixed up
* multi module jungfrau sync must do slaves first then master for start acquisition and send software trigger, and master first and then slaves for stopacquisition
* non blocking to slaves first and only then blocking/nonblocking to the master for sending software trigger(jungfrau multi mod sync)
* fixed get/set timing jungfrau when sync enabled, getsync during blocking acquire (for trigger or stop) will get stuck as it should ask the stop server
* switching between 1 and 2 interfaces did not set gui/client zmq port properly. Resulted in dummy streaming forever. fixed
* formatting, refactoring: const & for positions, multi mod M3 stop first master first
* adding missing cstdint for gcc 13
* Refactoring handle sync out, handling synchronization also for softwaretrigger for m3, for start/sync/stop for g2/g1
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
* fixed row and col for moench 2 interfaces
* fix moench getTiming and also allow moench to handle sync
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
* copied jungfrau server to moench and adapted
* fixed image size and num packets
* read n rows allows 16
* commneted out configure_asic_timer at server startup. To be removed later the ASIC_CTRL_REG and storage cell options
* moench:removing the decrement (which was in jf) in read n rows to register
* removed lblsamples from gui
- removed getClientServerAPIVersion in server (not used)
- removed rxr side (clientversion compatibility check), removed enum as well as it is now done on the client side.
- versionAPI.h
- GITBRANCH changed to RELEASE
- dates for all API changed to "sem_version date". Scripts to compile servers modified for this. Empty "branch" name will end up with developer for sem_version.
- Version class with constructor taking in the long version (APILIB date). Other member functions including concise(to get sem_version for new releases and date for old releases),
- bypassing initial tests, also now bypasses the client-rxr compatibility check (at rx_hostname command)
- previously, compatibility between client-det was ensuring both had the same detector API (eg. same APIJUNGFRAU)
- Now, compatibility only checks APILIB (client side) and detector API(eg. APIJUNGFRAU) (detector side) have same major version. It only does backward compatibility test. Rest is upto user to ensure.
- If server is from an older release, it will compare dates like previous implementation (APIJUNGFRAU from both client and det)
- - previously, compatibility between client-rxr was ensuring both had the same APIRECEIVER
- Now, compatibility only checks APILIB (client side) and APIRECEIVER (rxr side) have same major version. It only does backward compatibility test. Rest is upto user to ensure.
- If rxr is from an older release, it will compare dates like previous implementation (APIRECEIVER from both client and rxr)
- removed APIGUI, evalVersionVariables.sh, genVersionHeader.sh (not needed or not used)
- clientVersion, rxrversion and detectorserverversion all return strings and not integers (in hex) anymore. Depending if it has semantic versioning, it will print that or the date if it is too old.
- fixed in python (strings for versions)
- check_version function in detector server changed to "initial checks" as it only checks server-firmware compatibility and initial server checks. Client compatibilities are moved to client side.
- --version gives sem_version and date? Is date needed as well. The clientversion, detserverversion and rxrversion API gives only sem_version (no date)
- - formatting
