The vivado/vitis_hls detection, the hls target and the pcie_100g/pcie_8x10g (and _bd) targets are removed: the firmware is not built from this tree. docs/FPGA.md keeps the toolset version and the IP licence terms of the released bitstreams. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01HVeDQrPqZ52Tp6rzzZGxf3
45 lines
2.9 KiB
Markdown
45 lines
2.9 KiB
Markdown
# FPGA smartNIC
|
|
|
|
See separate document for [installation instructions](DEPLOYMENT.md).
|
|
|
|
## Hardware
|
|
Currently supported FPGA is only **Xilinx Alveo U55C**.
|
|
|
|
See AMD/Xilinx webpage for [card user guide (UG1469)](https://docs.xilinx.com/r/en-US/ug1469-alveo-u55c).
|
|
According to the user guide:
|
|
```
|
|
Alveo data center accelerator cards are designed to be installed into a data center server, where controlled air flow provides direct cooling.
|
|
```
|
|
|
|
The card needs to be placed in a PCI Express (PCIe) Gen4 x8 slot, though mechanically slot has to accommodate x16 card.
|
|
There is no need to connect additional power cable, as power of the card is not exceeding 75 W load available from PCIe edge connector.
|
|
Current power estimation is about 30 W when idle and 45 W in operation. The card has built-in protection, which will cut power to the card if HBM temperature is above 120°C.
|
|
|
|
Two variants of the card are available:
|
|
* `100g` - this variant operates one port in 100 Gbit/s mode and should be used when connecting detector via a switch.
|
|
* `8x10g` - this variant operates both QSFP ports at 4x10 Gbit/s. QSFP+ (40 Gbit/s) transceivers and MTO/MTP harness cables
|
|
are necessary. It is designed for detector directly connected to the Jungfraujoch server, without switch.
|
|
|
|
See [network documentation](FPGA_NETWORK.md) for details of network.
|
|
|
|
## Firmware
|
|
The firmware is not built from this repository: the HLS (`fpga/hls/`) and RTL (`fpga/hdl/`) sources are
|
|
kept as a reference of what the card does, and the build has no firmware targets. The bitstreams were
|
|
made with AMD (Xilinx) Vivado and Vitis HLS **2022.2**.
|
|
|
|
In addition to the Intellectual Property (IP) cores included in Vivado, two additional licenses are necessary:
|
|
* Non-cost license for Ultrascale+ 100G core has to be requested from AMD/Xilinx website, see [Xilinx website](https://www.xilinx.com/products/intellectual-property/cmac_usplus.html), to build `100g` design.
|
|
* A paid license for the 10G/25G Ethernet Subsystem for Ultrascale+ is necessary to build the `8x10g` design.
|
|
PSI received non-cost licenses from Xilinx University Program for the latter cores. Therefore, usage of bitstreams
|
|
generated by PSI continuous integration pipeline for `8x10g` is only allowed for non-commercial use.
|
|
|
|
### Firmware releases
|
|
The firmware is stable and is carried from version to version: the MCS files attached to a release
|
|
are normally the ones from the release before it (see [Release contents](RELEASE_CONTENTS.md)).
|
|
|
|
## Frame generator
|
|
|
|
The Jungfraujoch card is equipped with a frame generator. It allows simulating a JUNGFRAU detector without having access to such a system.
|
|
It sits in parallel with the Ethernet MAC, so it is placed before the network stack and before any processing happening on the card.
|
|
In the future a redirection will be possible to send the simulated stream through the 100G TX network link.
|
|
Frame generator is written in HLS and controlled with AXI-Lite. |