7f8a8b4247
secop: skip variables already mirrored from sea
2026-02-09 15:32:27 +01:00
4d7bcd4c12
fftf (amoroven) with pwm/low poeer switch
2026-02-09 15:24:55 +01:00
09c017cd2d
fixes to amor oven supporting PWM/direct switch
2026-02-09 11:22:11 +01:00
ff14e0f792
fix issue with rhfe sensors
...
load correct INTYPE (was overridden by 0)
2025-10-23 15:28:24 +02:00
59d665c85b
secop: fix bug when write failed
...
clear the property secoprequested in case an error message
is received
2025-09-03 10:30:15 +02:00
e8baff57d7
heliox: improve drivers
...
- adjustable sorb temperatures
- two phases: one for about 5 min at sorbset1, then sorbset2
2025-07-11 15:25:59 +02:00
4941232be6
add bool type to the displayed curves
2025-07-08 17:56:34 +02:00
893bd5fa4b
automatic LN2 fill with ILM - fix problems on restart
...
on the first reading, the level value might be invalid,
then it tries to fill and switch to inactive because there
is not valid level value.
fix: stay watching as long as the level is invalid
2025-07-04 10:51:54 +02:00
6a191e49da
revert: hepump/trinamic: set pullup resistors correctly
...
this was an error. the problem is the wiring.
2025-06-23 12:27:20 +02:00
b0720933a7
hepump/trinamic: set pullup resistors correctly
2025-06-17 16:03:41 +02:00
3201c9e3c9
cryotel: bug fix with cryotel::updatecool
2025-06-17 16:02:01 +02:00
a5738fd0d4
SECoP: add sea_recorder command and setups for sea recorder
...
NICOS might call this in order to start SEA recording from
SECoP servers
2025-06-17 13:04:11 +02:00
61eac1aa9b
dil12: add 'off' to the heater range enum
2025-06-17 12:59:53 +02:00
0d9a3d35f8
send ACTIVE only after all nodes are connected
...
used for sea_recorder
2025-06-17 11:41:09 +02:00
e819507c3e
fix typo
2025-06-17 11:39:38 +02:00
a87ac46fd8
tcl/drivers/ipsmag.tcl heater must be numeric
2025-05-08 09:05:58 +02:00
l_samenv
f125bf1f28
ah2700: fix issue with detecting echo
2025-02-28 11:27:34 +01:00
l_samenv
ee3e8d38d8
change samenv.psi.ch to linse-c.psi.ch
2025-02-28 11:27:07 +01:00
l_samenv
58113622bd
lsc370: try to improve behaviour with heater in open loop mode
2025-02-28 11:27:07 +01:00
l_samenv
24f15db38f
ah2550: fix auto detection and disabling of serial echo
2025-02-24 11:34:11 +01:00
l_samenv
b8218e6203
move a lot of stuff to git
2025-01-17 17:05:02 +01:00
l_samenv
be52adfaef
Merge branch 'master' of gitlab.psi.ch-samenv:samenv/sea
2025-01-09 18:08:36 +01:00
l_samenv
6737e3f736
hide calibration in mom driver
2025-01-09 18:07:24 +01:00
l_samenv
596fe4e37c
add ah2550 driver
2024-12-04 14:39:11 +01:00
6fa7cf8867
dblctrl: smart selection of mode (up, down, stable)
...
when switching from inactive to active
2024-11-26 15:26:08 +01:00
l_samenv
f5a129b6d9
improve autodevice deature
...
for autodevice to work, it is not necessary to be unplugged
for 60 seconds, only for a short time.
fixed this behaviour
2024-11-11 16:41:41 +01:00
l_samenv
5d8fa3b24f
do not set target parameter in error depending on status
2024-11-11 16:40:49 +01:00
35c5b225b6
heliux: improve condense deadline (soft_dealine)
2024-10-22 10:37:36 +02:00
l_samenv
bdd25b4ec7
improve coding for MA11 (codeb=0 Ohm)
...
+ was_uplugged should be cleared in proc samenv
2024-10-17 10:53:34 +02:00
c798f6b6c1
heliox: remove log message
2024-08-12 16:21:45 +02:00
512a892169
drivers/heliox.tcl: improve timeout
...
- softer implementation of timeout (depending on progress)
+ handle dblctrl correctly
2024-08-12 14:40:07 +02:00
a8f796a68d
ipsmag: increase timeout to 5
2024-08-12 08:54:27 +02:00
f01d850d10
ipslev (MA10): increase timeout
...
it seems that switching SLOW/FAST sometimes needs more than 2 sec.
increased timeout to 5
2024-08-12 08:53:11 +02:00
l_samenv
dc5e8f1999
RhFe curves: force using compensation on 340
...
use intype 0,2,2,10,8 instead of 6 (work only on 340)
2024-08-09 09:20:55 +02:00
l_samenv
0e8dfa767b
fix bug in hepump error log
...
the check that the pump is not running must run more frequently
than only every 30 seconds
2024-07-12 14:48:44 +02:00
l_samenv
d1170397c2
fix issue when unplug and plug happen within wshort time
...
see issue with MA10 on ZEBRA at 2024-04-26
http://samenv.psi.ch:8080/sample_environment/437
2024-06-27 14:52:25 +02:00
HAL-9500
e18346ff8e
put things from HAL-9500 muSR instrument into git
2024-05-21 08:29:44 +02:00
c68db8bc31
ccu4flow: improve ma7 release nv hack
2024-05-03 08:48:34 +02:00
3ea9b38051
dbctrl: fix issue not fixed properly
2023-11-02 16:55:00 +01:00
l_samenv
6ee460c2bd
Merge branch 'master' of gitlab.psi.ch-samenv:samenv/sea
2023-10-26 10:05:55 +02:00
l_samenv
4d1858560b
dirvers/nvstep: fixes
2023-10-26 10:05:26 +02:00
1760eaad7a
Merge branch 'master' of gitlab.psi.ch-samenv:samenv/sea
...
Conflicts:
tcl/drivers/hepump.tcl
2023-10-24 13:21:16 +02:00
7ccc96759e
catch around setmaintarget
2023-10-24 13:18:39 +02:00
5c5f0d3ef7
use tt.set.reg instead of tt.target for hepump auto eco
...
if available
2023-10-24 13:13:48 +02:00
33296cc03b
do not trigger error on level reading when inactive
2023-10-05 08:24:52 +02:00
8fcd4f8e1a
fix stick sensors on reload
...
it seems stick sensors are not installed properly sometimes
after restart. fix_stick_sensors is triggered for execution
on creation of an lsc object
2023-10-05 08:22:50 +02:00
l_samenv
2c13e9b091
catch the case when sensirion is not working
...
- add use_pressure to nv control for selecting whether nv control
is using the flow from the sensirion sensor or the pump pressure
- this is triggered when sensirion is reading 0 (incl. stddev)
2023-09-28 14:42:46 +02:00
882c55e95a
Merge branch 'master' of gitlab.psi.ch-samenv:samenv/sea
2023-09-25 13:21:26 +02:00
931ff58a2d
make nv flow ctrl more conservative
...
- reduce prop_o / prop_c
- increase Tmin from 1.5 to 10 (for autoflow)
2023-09-25 13:20:22 +02:00
l_samenv
4a930149c2
dil: remove "there might be some mixture" message
2023-09-21 10:52:34 +02:00
