Configuration commands

Commands to configure the detector. these commands are often left to the configuration file.

• Data Structure: commands to configure detector data structure
• Status: commands to configure detector status
• Data Size: commands to configure detector data size
• Flags: commands to configure detector flags
• Chip: commands to configure chip of the detector
• Versions: commands to check version of each subsytem
• Speed: commands to configure speed of detector
• Detector Parameters: commands to configure/retrieve configuration of detector

Data Structure

commands to configure detector data structure

• externalgui sets/gets external gui flag. 1 sets and enables the 0MQ data stream (0MQ threads created) from receiver to client, while 0 unsets and disables. Returns (int)

• free Free shared memory on the control PC

• add Adds a detector at the end of the multi-detector structure. put argument is the hostname or IP adress. Returns the chained list of detector hostnames.

• remove i Removes controller i from the multi-detector structure. Can be used for partial readout of the detector.

• type Sets/gets detector type. Returns (string). Normally not used. Using hostname is enough.

• hostname put adds the hostname (ot IP adress) at the end of the multi-detector structure. If used for a single controlled (i:) replaces the current hostname. Returns the list of the hostnames of the multi-detector structure. Returns (string)

• id[:i] Returns the id of the detector structure. i is the detector position in a multi detector system. If used a put, configures the id of the detector structure. i is the detector position in a multi detector system and l is the id of the detector to be added.

• master i put sets the position of the master of the acquisition (-1 if none). Returns the position of the master of the detector structure (-1 if none).

• sync Sets/gets the synchronization mode of the detectors in the multi-detector structure. Can be: none, gating, trigger, complementary. Mainly used by MYTHEN/GOTTHARD.

Status

commands to configure detector status

• online [i] sets the detector in online (1) or offline (0) mode. Returns (int)

• checkonline returns the hostnames of all detectors without connecting to them. Returns (string) "All online" or "[list of offline hostnames] : Not online".

• activate Activates/Deactivates the detector. Deactivated detector does not send data. Used for EIGER only. Returns (int)

Data Size

commands to configure detector data size

• nmod [i] sets/gets the number of modules of the detector. Used for MYTHEN only. Returns (int)

• maxmod Gets the maximum number of modules of the detector. Used for MYTHEN only. Cannot put! Returns (int)

• dr [i] sets/gets the dynamic range of detector. Mythen [4,8,16,24]. Eiger [4,8,16,32]. Others cannot put! Returns (int)

• roi [i] [xmin] [xmax] [ymin] [ymax] sets region of interest of the detector, where i is number of rois;i=0 to clear rois. Used for GOTTHARD only. Returns (int)

• detsizechan [xmax] [ymax] sets the maximum number of channels in each dimension for complete detector set; -1 is no limit. Use for multi-detector system as first command in config file. Returns ("int int")

• roimask [i] ?? Returns (int) in hexadecimal

• flippeddatax [i] enables/disables data being flipped across x axis. 1 enables, 0 disables. Used for EIGER only. 1 for bottom half-module, 0 for top-half module. Returns (int)

• tengiga [i] enables/disables 10GbE in system (detector & receiver). 1 enabled 10GbE, 0 enables 1GbE. Used in EIGER only. Returns (int)

Flags

commands to configure detector flags

• flags [flag] sets/gets the readout flags to mode. Options: none, storeinram, tot, continous, parallel, nonparallel, safe, digital, analog_digital, unknown. Used for MYTHEN and EIGER only. Returns (string). put takes one string and returns concatenation of all active flags separated by spaces.

• extsig:[i] [flag] sets/gets the mode of the external signal i. Options: off, gate_in_active_high, gate_in_active_low, trigger_in_rising_edge, trigger_in_falling_edge, ro_trigger_in_rising_edge, ro_trigger_in_falling_edge, gate_out_active_high, gate_out_active_low, trigger_out_rising_edge, trigger_out_falling_edge, ro_trigger_out_rising_edge, ro_trigger_out_falling_edge.
  Used in MYTHEN, GOTTHARD, PROPIX only. Returns (string)

• programfpga [file] programs the FPGA with file f (with .pof extension). Used for JUNGFRAU, MOENCH only. Only put! Returns ("successful", "unsuccessful")

• resetfpga [f] resets FPGA, where f can be any value. Used for JUNGFRAU only. Only put! Returns ("successful", "unsuccessful")

Chip

commands to configure chip of the detector

• powerchip [i] Powers on/off the chip. 1 powers on, 0 powers off. Can also get the power status. Used for JUNGFRAU only. Returns (int)

• led [i] sets/gets the led status. 1 on, 0 off. Used for MOENCH only ?? Returns (int)

• pulse [n] [x] [y] pulses pixel at coordinates (x,y) n number of times. Used in EIGER only. Only put! Returns ("successful", "unsuccessful")

• pulsenmove [n] [x] [y] pulses pixel n number of times and moves relatively by x value (x axis) and y value(y axis). Used in EIGER only. Only put! Returns ("successful", "unsuccessful")

• pulsechip [n]pulses chip n number of times, while n=-1 will reset it to normal mode. Used in EIGER only. Only put! Returns ("successful", "unsuccessful")

Versions

Commands to check versions of each subsystem

• moduleversion:[i] Gets the firmware version of module i. Used for MYTHEN only. Only get! Returns (long int) in hexadecimal or "undefined module number"

• detectornumber Gets the serial number or MAC of detector. Only get! Returns (long int) in hexadecimal

• modulenumber:[i] Gets the serial number of module i. Used for MYTHEN only. Only get! Returns (long int) in hexadecimal or "undefined module number"

• detectorversion Gets the firmware version of detector. Only get! Returns (long int) in hexadecimal

• softwareversion Gets the software version of detector server. Only get! Returns (long int) in hexadecimal

• thisversion Gets the software version of this client software. Only get! Returns (long int) in hexadecimal

• receiverversion Gets the software version of receiver. Only get! Returns (long int) in hexadecimal

• framesl gets number of frames left. Used in MYTHEN, GOTTHARD only. Only get! Returns (double with 9 decimal digits)

Speed

commands to configure speed of detector

• clkdivider [i] sets/gets the readout clock divider. EIGER, JUNGFRAU [0(fast speed), 1(half speed), 2(quarter speed)]. MYTHEN[???]. Returns (int)

• setlength [i] sets/gets length of set/reset signals (in clock cycles). Used in MYTHEN only. Returns (int)

• waitstates [i] sets/gets waitstates of the bus interface (in clock cycles). Used in MYTHEN only. Returns (int)

• totdivider [i] sets/gets clock divider in tot mode. Used in MYTHEN only. Returns (int)

• totdutycycle [i] sets/gets duty cycle of the tot clock. Used in MYTHEN only. Returns (int)

• phasestep [i] Only put for gotthard. Moves the phase of the ADC clock.Returns (int)

• oversampling [i] Sets/gets the number of adcsamples per clock. For the new chiptestboard.Returns (int)

• adcclk [i] sets/gets the ADC clock frequency in MHz. For the new chiptestboard!Returns (int)

• adcphase [i] Sets/gets the ADC clock frequency in MHz. For the new chiptestboard!Returns (int)

• adcpipeline [i] Sets/gets the pipeline of the ADC. For the new chiptestbaord!Returns (int)

• dbitclk [i] Sets/gets the clock frequency of the latching of the digital bits in MHz. For the new chiptestboard!Returns (int)

• dbitphase [i] Sets/gets the phase of the clock for latching of the digital bits. For the new chiptestboard!?Returns (int)

• dbitpipeline [i] Sets/gets the pipeline of the latching of the digital bits. For the new chiptestbaord!Returns (int)

Detector Parameters

commands to configure/retrieve configuration of detector

• config [fname] sets/saves detector/receiver to configuration contained in fname. Same as executing sls_detector_put for every line. Normally a one time operation. Returns (string) fname

• rx_printconfig prints the receiver configuration. Only get! Returns (string)

• parameters [fname] sets/saves detector parameters contained in fname. Normally once per different measurement. Returns (string) fname

• setup [fname] sets/saves detector complete setup contained in fname (extensions automatically generated), including trimfiles, ff coefficients etc. Returns (string) fname