Commands to configure the detector. these commands are often left to the configuration file.
commands to configure detector structure
- datastream enables/disables the 0MQ data stream (0MQ threads created) from receiver to client.
- free Free shared memory on the control PC
- add Adds a detector at the end of the multi-detector structure.
put argument is the hostname or IP adress. Returns the chained list of detector hostnames.
- remove i Removes controller
i from the multi-detector structure. Can be used for partial readout of the detector.
- type Sets/gets detector type (string).
- hostname
put adds the hostname (ot IP adress) at the end of the multi-detector structure. If used for a single controlled (i:) replaces the current hostname. Returns the list of the hostnames of the multi-detector structure.
- id[:i] Returns the id of the detector structure. i is the detector position in a multi detector system. If used a
put, configures the id of the detector structure. i is the detector position in a multi detector system and l is the id of the detector to be added.
- master i
put sets the position of the master of the acquisition (-1 if none). Returns the position of the master of the detector structure (-1 if none).
- sync Sets/gets the synchronization mode of the detectors in the multi-detector structure. Can be:
none, gating, trigger, complementary. Mainly used by MYTHEN/GOTTHARD.
commands to configure detector status
- online [i] sets the detector in online (1) or offline (0) mode
- checkonline returns the hostnames of all detectors without connecting to them
- activate Activates/Deactivates the detector. Deactivated detector does not send data. Used for EIGER only.
commands to configure detector data size
- nmod [i] sets/gets the number of modules of the detector. Used for MYTHEN only.
- maxmod Gets the maximum number of modules of the detector. Used for MYTHEN only. Cannot put!
- dr [i] sets/gets the dynamic range of detector. Mythen [4,8,16,24]. Eiger [4,8,16,32]. Others cannot put!
- roi [i] [xmin] [xmax] [ymin] [ymax] sets region of interest of the detector, where i is number of rois;i=0 to clear rois. Used for GOTTHARD only.
- detsizechan [xmax] [ymax] sets the maximum number of channels in each dimension for complete detector set; -1 is no limit. Use for multi-detector system as first command in config file.
- flippeddatax [i] enables/disables data being flipped across x axis. 1 enables, 0 disables. Used for EIGER only. 1 for bottom half-module, 0 for top-half module.
- lock [i] Locks/Unlocks the detector to communicate with this client. 1 locks, 0 unlocks.
- flags [flag] sets/gets the readout flags to mode. Options: none, storeinram, tot, continous, parallel, nonparallel, safe, digital, analog_digital, unknown. Used for MYTHEN and EIGER only.
- extsig:[i] [flag] sets/gets the mode of the external signal i. Options:
off, gate_in_active_high, gate_in_active_low, trigger_in_rising_edge, trigger_in_falling_edge, ro_trigger_in_rising_edge, ro_trigger_in_falling_edge, gate_out_active_high, gate_out_active_low, trigger_out_rising_edge, trigger_out_falling_edge, ro_trigger_out_rising_edge, ro_trigger_out_falling_edge.
Used in MYTHEN, GOTTHARD, PROPIX only.
- programfpga [file] programs the FPGA with file f (with .pof extension). Used for JUNGFRAU, MOENCH only. Only put!
- resetfpga [f] resets FPGA, where f can be any value. Used for JUNGFRAU only. Only put!
- powerchip [i] Powers on/off the chip. 1 powers on, 0 powers off. Can also get the power status. Used for JUNGFRAU only.
- led [i] sets/gets the led status. 1 on, 0 off. Used for MOENCH only ??
Commands to check versions of each subsystem
- timing [mode] sets/gets synchronization mode of the detector. Mode: auto, trigger, ro_trigger, gating, triggered_gating
- exptime [i] sets/gets exposure time in s
- subexptime [i] sets/gets sub exposure time in s. Used in EIGER only in 32 bit mode.
- period [i] sets/gets frame period in s.
- delay [i] sets/gets delay in s. Used in MYTHEN, GOTTHARD only
- gates [i] sets/gets number of gates. Used in MYTHEN, GOTTHARD, EIGER only
- gates [i] sets/gets number of frames. If
timing is not auto, then it is the number of frames per cycle/trigger.
- cycles [i] sets/gets number of triggers. Timing mode should be set appropriately.
- probes [i] sets/gets number of probes to accumulate. When setting, max 3! cycles should be set to 1, frames to the number of pump-probe events. Used in MYTHEN only
- measurements [i] sets/gets number of measurements.
- samples [i] sets/gets number of samples expected from the jctb. Used in CHIP TEST BOARD only.
- exptimel gets exposure time left. Used in MYTHEN, GOTTHARD only. Only get!
- periodl gets frame period left. Used in MYTHEN, GOTTHARD only. Only get!
- delayl gets delay left. Used in MYTHEN, GOTTHARD only. Only get!
- gatesl gets number of gates left. Used in MYTHEN, GOTTHARD only. Only get!
- framesl gets number of frames left. Used in MYTHEN, GOTTHARD only. Only get!
- cyclesl gets number of cylces left. Used in MYTHEN, GOTTHARD only. Only get!
- probesl gets number of probes left. Used in MYTHEN, GOTTHARD only. Only get!
- clkdivider [i] sets/gets the readout clock divider. EIGER, JUNGFRAU [0(fast speed), 1(half speed), 2(quarter speed)]. MYTHEN[???]
- clkdivider [i] sets/gets length of set/reset signals (in clock cycles). Used in MYTHEN only
- clkdivider [i] sets/gets waitstates of the bus interface (in clock cycles). Used in MYTHEN only
- clkdivider [i] sets/gets clock divider in tot mode. Used in MYTHEN only
- clkdivider [i] sets/gets duty cycle of the tot clock. Used in MYTHEN only
- adcphase [i] ??? Used in MYTHEN, JUNGFRAU only.
- config [fname] sets/saves detector/receiver to configuration contained in fname. Same as executing sls_detector_put for every line. Normally a one time operation.
- rx_printconfig prints the receiver configuration. Only get!
- parameters [fname] sets/saves detector parameters contained in fname. Normally once per different measurement.
- setup [fname] sets/saves detector complete setup contained in fname (extensions automatically generated), including trimfiles, ff coefficients etc.
- tengiga [i] enables/disables 10GbE in system (detector & receiver). 1 enabled 10GbE, 0 enables 1GbE. Used in EIGER only.
- pulse [n] [x] [y] pulses pixel at coordinates (x,y) n number of times. Used in EIGER only. Only put!
- pulsenmove [n] [x] [y] pulses pixel n number of times and moves relatively by x value (x axis) and y value(y axis). Used in EIGER only. Only put!
- pulsechip [n]pulses chip n number of times, while n=-1 will reset it to normal mode. Used in EIGER only. Only put!
1.6.1