* transceiverenable, tsamples, romode for tranceiver and digital_transceiver
* 202 spec instr only for transceiver mode
* removed check for empty in trans readout and clean memory before reading from fifo
* ctb read fifo strobe for all after reading all channels, adding 1us after selecting channel, changing fw date
* updated 10gb transceiver enable
----
* added transceiver (tsamples, romode(transceiver, digital_transceiver), transceiverenable (mask)
* clean memory before reading from fifo (for analog and digital as well)
* read fifo then read strobe (also corresp fw) fixes number of reads (also for analg and digital)-> increases all pipelines by 1
* fixed bug in rearranging digital data in receiver
* fixed bug in streaming size of data after rearranging
* fixed bug in setbit, clearbit,and getbit
* status checks fifo before returning idle (transmitting if data in fifo if transceiver more enabled)
* soem matterhorn specifics that will need to be put into pattern in a month or two. this is temporary.
* NOTE: breaking api. rxParameters struct has transceiverenabel and tsamples given from det to receiver
* when dbit list is enabled, the size of data in zmq stream is changed to only the digital bits enabled size. now fixed to also include analog size
* allowing to set 0xffffffffffffffff to pat io control. prevously was used to do a get. fixed also for pat bit mask and pat mask
- start acq list: mixup with master pos #743 : fix that only master starts second and not all (for start acq), typo with pos and masters list
- synced master status running when setting to slave #747: synced master status running when setting to slave
* moench, removed chip version, filter resistor, filter cells, currentsoures, gain mode, setttings(modes), dbitphase, maxdbitphase, autocompdisable, comparatordisabletime, made acq start and stop a pulse, removed unused registers
* added parallel command
* remove gain plot for moench
* moench: updated adc invert val
* moench: update adcoffset to 0xf and adcphase to 140 degrees
* removed sync clock in moench
* updated min fw version
* removing config file in moench server
* Revert "Ctb: allow adc mask enable to be 0 for 1 and 10GbE (#750)"
This reverts commit a0f250a4876937ebb2a96c8948fdea380625a86e.
* better error message about setting adc mask to 0. Cannot set it to 0 due to ram allocation
* using argparse for parsing command line arguments
* added command line option to specify which servers to run
---------
Co-authored-by: Erik Fröjdh <erik.frojdh@gmail.com>
adding rx_roi also in the zmq header for external guis to put the "yellow box".. sending full roi instead of -1, and sending for each zmq port. "(multiple yellow boxes)".
* merge fix from #721 PR (sync) 7.0.2.rc -> developer
* row and column for jungfrau mixed up
* multi module jungfrau sync must do slaves first then master for start acquisition and send software trigger, and master first and then slaves for stopacquisition
* non blocking to slaves first and only then blocking/nonblocking to the master for sending software trigger(jungfrau multi mod sync)
* fixed get/set timing jungfrau when sync enabled, getsync during blocking acquire (for trigger or stop) will get stuck as it should ask the stop server
* switching between 1 and 2 interfaces did not set gui/client zmq port properly. Resulted in dummy streaming forever. fixed
* formatting, refactoring: const & for positions, multi mod M3 stop first master first
* adding missing cstdint for gcc 13
* Refactoring handle sync out, handling synchronization also for softwaretrigger for m3, for start/sync/stop for g2/g1
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
* fixed row and col for moench 2 interfaces
* fix moench getTiming and also allow moench to handle sync
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
Firmware updated. spi moved to firmware. In Software, configuring, then a pulse to start, wait for done bit and convert the values read from a regiter.
* modified ZMQonline display for stripsel usage. modified dataprocessor to overwrite header.detspec1 with ROI in case of ROI.
* Removing changes to the slsReceiver, moved to branch jf_zeromq_display_rxroi
* rx_hostname and port combo to one, or hostname to all, or a vector of hostnames and ports, ignoring none or empty, then verifying no duplicates for the host port combo including from shared memory
* extracted function for rx_hostname (#694)
* c++14 revert
* unique hostname-port combo for port, hostname, rx_tcpport (#696)
* verify unique combo for rx_port as well
* check unique hostname-port combo also when setting control port, hostname, rx_hostname and rx_tcpport
---------
Co-authored-by: Erik Fröjdh <erik.frojdh@gmail.com>
Co-authored-by: Erik Frojdh <erik.frojdh@psi.ch>
