* voltage regulators only looks at dac and not at ctrl_reg
* xilinx: change dac max to 2048, setting dac ist not inverse conversion from dac to voltage anymore, but setting power is inverse, also there is max and min to power, a different min for vio and this is checked at funcs interface, not printign or converting to mv in dac for power regulators (as its conversion max and min are different)
* Use links for dacs/adc and adapt power rglt thresholds
* Remove wait for transceiver reset
* adc and dac device not used anymore and hence removed
* udp restucturing: arm has to be multiple of 16 and no byteswap in udp_gen, option to compile locally in arm architecture, memsize of the second udp memory has to be limited
---------
Co-authored-by: Martin Brückner <martin.brueckner@psi.ch>
* changed common.c readADCFromFile to make it more general and move temperature calculation for Eiger out of this function and inside whereever it is called.
* g2 and m2: gethighvoltage was just a variable set in server, it is now moved to a get inside DAC5671 implementation (but not reading a measured value, instead what is set from a file), high voltage variable used inside DAC5671 for virtual servers
* g2: switching off hv (ifrom non zero to zero value) will wait for 10s; powering on chip reconfigures chip; powering off chip unconfigures chip; powering off chip also includes check if hv = 0, if not throw exception; chip configuration checked before acquring; at start up: hv switched off and chip powered on, so does not wait 10s to switch off hv;
* included test to check powering off chip when hv is on should throw an exception
* g2: check if chip configured before acquiring
* nios: read hv value set from file and virtual still goes into DAC5671 for conversions to and fro dac to V, change common readadc to readparameter to generalize, make sethighvoltage into a get and set to catch errors in get as well, g2: if not at startup, remmeber hv value before setting it and after check if value was being switched off (from a non zero value) and wait 10s if it was (10s wait only for switching off from non zero and not at startup)
* m3: clk 0 changed from 10 to 20 (100MHz to 50MHz)
* g2: startup clk div back to 10 as in firmware but setting in software startup to 20
* m3: minor print error if clk divider > max
* period and exptime(patternwaittime level 0)
* added new regsieterdefs and updated api version and fixedpattern reg
* autogenerate commands
* formatting
* minor
* wip resetflow, readout mode, transceiver mask, transceiver enable
* acquisition, but streaming done bit and busy (exposing + read chip to fifo) not known yet from fw
* programming fpga and device tree done
* most configuration done, need to connect configuretransceiver to client
* stuck at resetting transciever timed out
* minor
* fixed virtual, added chip busyto fifo, streaming busy, set/getnext framenumber
* configuretransceiver from client, added help in client
* make formatt and command generation
* tests for xilinx ctb works
* command generation
* dacs added and tested, power not done
* power added
* added temp_fpga
* binaries in
* ctrlreg is 0 to enable chip=fixed, high dac val = min val= fixed, power regulators in weird order=fixed, device tree could be loaded with dacs before adcs=fixed
* start works
* virtual server sends
* receiver works
* tests
* python function and enum generation, commands generatorn and autocomplete, formatting, tests
* tests fail at start(transceiver not aligned)
* tests passed
* all binaries compiled
* eiger binary in
* added --nomodule cehck for xilinx
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* connected kernelversion, hardwareversion, versions, framesl, triggersl, dr, timingmode, pattern (except patioctrl) thats there for altera ctb
* replaced set/get64Bit to set/getU64bit in all loadpattern.c for (ctb and m3 also)
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* allowing tests for xilinx
* binaries in
* updated registers, arm64
* compiler set to aarch64 for xilinx server
* updated RegisterDefs.h
* merge into generate branch and resolving conflicts and adding the xilinx changes to callerspecial and commands.yaml
* compiles and can print firmware version (using a different csp0 address)
* fixing other servers (gotthard, jungfrau, moench, mythen3) that it returns in case of mapping failure, xilinxctb: added that it checks type, prints proper fw version, checks kernel date, added armprocessor define to use in common places, added specifiers to supress overflow and truncation warnings
* added detector ip and mac adddress to the printout
* fixed tests and recompiled servers
* draft to fix virtual test when it fails
* catching errors in tests and removing sigchild ignore so servers (process in background) executing commands will not fail (pclose no child processes, if sigchld is ignored) fixed
* uncommented python loading config
* somehow killal slsReciever in second detector test fails even though no receiver running
* fixing script for virtual simlator test:fixed issue with check if process running, fixed moench tests
* jf: if bit 14 in reg 0x5d (electron mode collection bit) is changed, configure chip if v1.1 and powered on. so touch writeregister (setbit/clearbit also calls write register in the end). replace when electroncollectionmode command introduced
* jf: rewrite of status reg bits, waiting state includes both wati for trigger and start frame, blocking trigger only waits if its not in waiting for trigger and run busy enabled, error state connected in firmware
* merge fix from 7.0.2: new jungfrau fw versions, incremented binary, hdf5 and json versions
* moench: changed dac names and default values to old moench values
* moench: remove interface clk polarity at start up
* moench: default speed is half speed, default values for adc offset and adc phase for different speeds (only half speed confirmed), adc vref voltage to 2.0 like G1
* moench: connected adc pipeline to client
* moench: receiver- default frames per file is 100k and discard partial frames as default
* moench binary in
* using tostring in gui for dacs
* moved frame discard policy as a parameter to be configured with a default depending on detector
* moench: 300 degrees for adc phase in full speed
* transceiverenable, tsamples, romode for tranceiver and digital_transceiver
* 202 spec instr only for transceiver mode
* removed check for empty in trans readout and clean memory before reading from fifo
* ctb read fifo strobe for all after reading all channels, adding 1us after selecting channel, changing fw date
* updated 10gb transceiver enable
----
* added transceiver (tsamples, romode(transceiver, digital_transceiver), transceiverenable (mask)
* clean memory before reading from fifo (for analog and digital as well)
* read fifo then read strobe (also corresp fw) fixes number of reads (also for analg and digital)-> increases all pipelines by 1
* fixed bug in rearranging digital data in receiver
* fixed bug in streaming size of data after rearranging
* fixed bug in setbit, clearbit,and getbit
* status checks fifo before returning idle (transmitting if data in fifo if transceiver more enabled)
* soem matterhorn specifics that will need to be put into pattern in a month or two. this is temporary.
* NOTE: breaking api. rxParameters struct has transceiverenabel and tsamples given from det to receiver
* when dbit list is enabled, the size of data in zmq stream is changed to only the digital bits enabled size. now fixed to also include analog size
* allowing to set 0xffffffffffffffff to pat io control. prevously was used to do a get. fixed also for pat bit mask and pat mask
- start acq list: mixup with master pos #743 : fix that only master starts second and not all (for start acq), typo with pos and masters list
- synced master status running when setting to slave #747: synced master status running when setting to slave
* moench, removed chip version, filter resistor, filter cells, currentsoures, gain mode, setttings(modes), dbitphase, maxdbitphase, autocompdisable, comparatordisabletime, made acq start and stop a pulse, removed unused registers
* added parallel command
* remove gain plot for moench
* moench: updated adc invert val
* moench: update adcoffset to 0xf and adcphase to 140 degrees
* removed sync clock in moench
* updated min fw version
* removing config file in moench server
* Revert "Ctb: allow adc mask enable to be 0 for 1 and 10GbE (#750)"
This reverts commit a0f250a4876937ebb2a96c8948fdea380625a86e.
* better error message about setting adc mask to 0. Cannot set it to 0 due to ram allocation
* merge fix from #721 PR (sync) 7.0.2.rc -> developer
* row and column for jungfrau mixed up
* multi module jungfrau sync must do slaves first then master for start acquisition and send software trigger, and master first and then slaves for stopacquisition
* non blocking to slaves first and only then blocking/nonblocking to the master for sending software trigger(jungfrau multi mod sync)
* fixed get/set timing jungfrau when sync enabled, getsync during blocking acquire (for trigger or stop) will get stuck as it should ask the stop server
* switching between 1 and 2 interfaces did not set gui/client zmq port properly. Resulted in dummy streaming forever. fixed
* formatting, refactoring: const & for positions, multi mod M3 stop first master first
* adding missing cstdint for gcc 13
* Refactoring handle sync out, handling synchronization also for softwaretrigger for m3, for start/sync/stop for g2/g1
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
* fixed row and col for moench 2 interfaces
* fix moench getTiming and also allow moench to handle sync
---------
Co-authored-by: Erik Frojdh <erik.frojdh@gmail.com>
