up
No files matched your search
@@ -17,6 +17,9 @@ by `Build_Characterization_Report.bat`. Before report work, read
|
||||
- Transfer the workbook's repository URL to page 1 under the exact label `Repository`.
|
||||
- A template, configuration or successful build is not proof of FAT acceptance.
|
||||
- Never fabricate identities, limits, measurements, calibration or uncertainty.
|
||||
- For motor report data, inspect `Motor/Motor.xlsx` first when present, then
|
||||
use other `Motor/` documents only to resolve fields not supplied by that
|
||||
workbook. Keep each reported value traceable to its Motor-folder source.
|
||||
|
||||
## Privacy
|
||||
|
||||
|
||||
@@ -0,0 +1,200 @@
|
||||
# OWIS stage with ED7062 CSV and TR SSI encoder
|
||||
|
||||
This folder configures the OWIS linear stage with an ED7062 two-channel stepper
|
||||
drive in cyclic synchronous velocity (CSV) mode. ECMC closes the position loop
|
||||
using the TR-Electronic LT140-S absolute SSI linear encoder. The configured
|
||||
engineering unit is millimetres.
|
||||
|
||||
The configuration was derived from `../EL7062_CSV`, but all drive declarations
|
||||
and descriptions in this folder refer to the ED7062.
|
||||
|
||||
## ED7062 declarations
|
||||
|
||||
| Setting | Configured value |
|
||||
| --- | --- |
|
||||
| Hardware description | `HW_DESC=ED7062` |
|
||||
| EtherCAT slave position | 10 |
|
||||
| Used channel | Channel 1 |
|
||||
| Unused channel | Channel 2, `Generic-Ch-Not-Used` |
|
||||
| Axis mode | `CSV` |
|
||||
| Drive setpoint | `velocitySetpoint01` |
|
||||
| Drive/control type | `1`, DS402/advanced drive |
|
||||
| Internal position | `positionActual01` |
|
||||
| Digital limit inputs | `binaryInputs01.0` and `.1` |
|
||||
|
||||
The declaration and PDO pattern follow PSI's ED7062 CSV example:
|
||||
|
||||
- [PSI EX7062/ED7062 CSV example](https://github.com/paulscherrerinstitute/ecmccfg/tree/b30e46072f900b37f7c674aee9a77b3c18f27735/examples/PSI/best_practice/motion/stepper_incremental/ex7062_CSV)
|
||||
- [PSI CSV/CSP/CSP-PC mode documentation](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/modes_csv_csp_csp_pc/)
|
||||
- [PSI axis YAML documentation](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/axisyaml/)
|
||||
|
||||
The copied EL7062-specific CSV firmware warning is intentionally not presented
|
||||
as an ED7062 fact. The files contain no evidence about the installed ED7062
|
||||
firmware; its disable/re-enable behaviour must still be checked on hardware.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, `EC_RATE=500` Hz |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS Stage ED7062` |
|
||||
| Stepper drive | ED7062 at EtherCAT slave 10, channel 1, CSV mode |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum, 0.5 A standby, 48 V nominal, 7.5 ohm/phase, 3080 uH, 400 full steps/revolution |
|
||||
| Primary feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Limit-switch supply | EL2008 slave 5, channel 4 switched output |
|
||||
| Position unit | mm |
|
||||
|
||||
## CSV drive scaling
|
||||
|
||||
The ED7062 CSV velocity setpoint uses a signed 32-bit range. With a stage travel
|
||||
of 1 mm/revolution and a 500 Hz EtherCAT rate:
|
||||
|
||||
```text
|
||||
drive.numerator = 1 mm/revolution * 500 cycles/second = 500
|
||||
drive.denominator = 2^31 = 2147483648
|
||||
|
||||
raw velocity = commanded velocity * 2147483648 / 500
|
||||
commanded velocity = raw velocity * 500 / 2147483648 mm/s
|
||||
```
|
||||
|
||||
At the configured default velocity of 3 mm/s, the nominal raw command is about
|
||||
`12884902` counts. Confirm the live setpoint and actual velocity during reduced-
|
||||
speed commissioning.
|
||||
|
||||
## Encoder configuration
|
||||
|
||||
### Primary SSI encoder
|
||||
|
||||
The EL5042 channel is configured by SDO before the axis is loaded:
|
||||
|
||||
- SSI mode, binary coding
|
||||
- 24 position bits, no multiturn or offset bits
|
||||
- Status bits disabled and CRC inversion enabled
|
||||
- 1 MHz clock
|
||||
- 9.0 V encoder supply
|
||||
- Scale: `1 / 10000 mm/count`, equivalent to `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Counter overflow/wraparound disabled
|
||||
|
||||
The `10000 counts/mm` value is labelled as interferometer-calibrated in
|
||||
`cfg/axis.yaml`. The files do not establish its calibration uncertainty or
|
||||
confirm the current mechanical datum.
|
||||
|
||||
### ED7062 internal counter
|
||||
|
||||
- Secondary encoder; the SSI encoder remains primary feedback
|
||||
- Scale: `1 / 1048576 mm/count` for a 1 mm/revolution stage
|
||||
- Incremental, 32-bit counter
|
||||
- Referenced to the primary SSI encoder at startup
|
||||
- Position PDO: `positionActual01`
|
||||
|
||||
## Position controller
|
||||
|
||||
In CSV mode, ECMC generates the trajectory and closes the position loop using
|
||||
the SSI encoder. The ED7062 closes its internal velocity and current loops.
|
||||
|
||||
The configured ECMC controller gains are:
|
||||
|
||||
| Parameter | Value |
|
||||
| --- | ---: |
|
||||
| `Kp` | 14 |
|
||||
| `Ki` | 1.6 |
|
||||
| `Kd` | 0.5 |
|
||||
| `Kff` | 1 |
|
||||
|
||||
These values differ substantially from the copied EL7062 configuration and are
|
||||
treated as local tuning values. Their origin and stability are not established
|
||||
by the files. Validate them at reduced current and velocity before normal motion.
|
||||
|
||||
## Motion and monitoring
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Trajectory profile | Trapezoidal (`type: 0`) |
|
||||
| Default velocity | 3 mm/s |
|
||||
| Default acceleration/deceleration | 2 mm/s^2 |
|
||||
| Emergency deceleration | 10 mm/s^2 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 10 mm/s |
|
||||
| Following-error tolerance | 0.5 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.002 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 10 s |
|
||||
| Automatic disable delay | 10 s idle |
|
||||
|
||||
The hardware limits use ED7062 channel 1 inputs:
|
||||
|
||||
- Backward limit: `binaryInputs01.0`
|
||||
- Forward limit: `binaryInputs01.1`
|
||||
- Limit-switch power: EL2008 channel 4
|
||||
|
||||
Home and external interlock are constant true because no corresponding sensors
|
||||
are assigned. Software limits and axis monitoring remain enabled.
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code_2.plc` at a 500 ms PLC sample period. A rising edge
|
||||
on `doMotion` starts the sequence.
|
||||
|
||||
- Move velocity: 2 mm/s
|
||||
- Acceleration and deceleration: 3 mm/s^2
|
||||
- Ten measurement positions from 1.0000 mm to 90.0000 mm
|
||||
- A preliminary position 0.2 mm below each measurement point
|
||||
- Intermediate dwell: 2 PLC scans, nominally 1 s
|
||||
- Measurement dwell: 12 PLC scans, nominally 6 s
|
||||
- Five forward/backward cycles
|
||||
|
||||
```sh
|
||||
# Start
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
|
||||
# Stop
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Remaining commissioning issues
|
||||
|
||||
- The motor component declares `R_COIL_MOHM=7500`, while the drive-controller
|
||||
component declares `R_COIL_MOHM=2471`. Resolve this mismatch before enabling
|
||||
motion. Use motor measurements and ED7062 autotune results for the installed
|
||||
motor rather than assuming the copied values are valid.
|
||||
- Confirm that `HW_DESC=ED7062` matches the installed device and the available
|
||||
`ecmccfg 11.0.8` hardware definition before starting the IOC.
|
||||
- Confirm the EL5042 output is 9.0 V and permitted by the exact encoder order
|
||||
code before connecting the encoder.
|
||||
- Confirm motor direction and SSI direction before closing the position loop. A
|
||||
sign error can command immediate motion in the wrong direction.
|
||||
- The PLC accepts busy-low plus `attarget` as move completion without first
|
||||
latching that busy became high. Validate or correct this handshake before
|
||||
unattended operation.
|
||||
- Static review does not prove PDO compatibility, controller stability, limit
|
||||
polarity, or safe operation on the target hardware.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EL5042 SDOs, ED7062 declaration, motor/controller components,
|
||||
axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - ED7062 CSV mapping, primary SSI feedback, trajectory,
|
||||
controller, limits, and monitoring
|
||||
- `cfg/enc_open_loop.yaml` - secondary ED7062 internal counter
|
||||
- `cfg/code_2.plc` - active FAT motion sequence
|
||||
- `cfg/code.plc` - alternate older sequence, not loaded by `startup.cmd`
|
||||
|
||||
## Commissioning sequence
|
||||
|
||||
1. Confirm that the IOC loads `ECMC/ED7062_CSV/startup.cmd`.
|
||||
2. Verify that EtherCAT slave 10 is the installed ED7062 and that channel 1 is
|
||||
connected to the motor while channel 2 is unused.
|
||||
3. Resolve the motor-resistance mismatch and run the appropriate drive autotune.
|
||||
4. Confirm 9.0 V at the EL5042 connector before attaching the encoder.
|
||||
5. With motion disabled, verify SSI readiness, position, status bits, ED7062
|
||||
counter, limit inputs, and limit-switch supply.
|
||||
6. Enable at reduced current and command a very low positive motion. Confirm
|
||||
motor direction, SSI direction, `velocitySetpoint01`, and actual velocity.
|
||||
7. Verify the 500/2147483648 CSV scaling against live setpoint and velocity.
|
||||
8. Tune and validate the ECMC position controller, following error, settling,
|
||||
software limits, and stop behaviour.
|
||||
9. Test disable/re-enable counter continuity on the installed ED7062 firmware.
|
||||
10. Validate the PLC execute/busy handshake before running the complete FAT
|
||||
sequence.
|
||||
@@ -0,0 +1,105 @@
|
||||
axis: # Physical-axis configuration
|
||||
id: ${AXIS_ID=1} # Unique numeric axis identifier
|
||||
feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=04} # EL2008 channel 4: 24 V supply for limit switches
|
||||
type: joint # Physical motor axis
|
||||
mode: CSP # ED7062 cyclic synchronous velocity mode
|
||||
autoEnable: # Native ecmc automatic axis enable/disable
|
||||
enableTimeout: 10 # Maximum time allowed to auto-enable [s]
|
||||
disableTimeout: 10 # Idle time before automatic disable [s]
|
||||
tweakDist: 1.0
|
||||
|
||||
plc: # Axis PLC configuration
|
||||
id: 1 # PLC identifier
|
||||
enable: yes # Enable the axis PLC
|
||||
externalCommands: true # Allow the PLC to issue axis commands
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1}
|
||||
precision: 3
|
||||
description: OWIS Stage ED7062
|
||||
unit: mm
|
||||
motorRecord:
|
||||
syncSoftLimits: False
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen'
|
||||
|
||||
|
||||
drive:
|
||||
numerator: 1 #500 # 1 mm/rev * 500 EtherCAT cycles/s
|
||||
denominator: 1048576 #2147483648 # Signed 32-bit ED7062 CSV velocity range
|
||||
type: 1 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).positionSetpoint01 # ED7062 CSV velocity setpoint
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word EtherCAT entry
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word EtherCAT entry
|
||||
warning: 2 # Warning bit in status word (if no drive warning bit then leave empty)
|
||||
error: # max 3 error bits in status word
|
||||
- 3 # Error 0 (if no drive error bit then leave empty)
|
||||
- 7 # Error 1 (if no drive error bit then leave empty)
|
||||
- 14 # Error 2 (if no drive error bit then leave empty)
|
||||
|
||||
encoder: # Primary encoder configuration
|
||||
primary: true # Use this encoder as the primary feedback encoder
|
||||
desc: SSI # Encoder description: TR-Electronic LT140-S SSI
|
||||
numerator: 1 # Encoder scaling numerator [mm]
|
||||
denominator: 10000 # Interferometer-calibrated encoder scale [counts/mm]
|
||||
type: 1 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 24 # Total raw encoder data width [bits]
|
||||
absBits: 24 # Absolute-data width in the least-significant part of the raw value [bits]
|
||||
absOffset: -11.826 # Absolute encoder offset in engineering units [mm]
|
||||
allowOverUnderFlow: false # Disallow raw-counter wraparound for this linear encoder
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # EtherCAT encoder actual-position entry
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # EtherCAT encoder status-word entry; required by warning/error checks
|
||||
ready: 2 # Ready-bit index in the encoder status word
|
||||
warning: 0 # Warning-bit index in the encoder status word
|
||||
error: # Encoder-error bit indices in the status word; maximum three
|
||||
- 1 # Encoder error 0 bit
|
||||
delayComp: # Compensation for delay between setpoint output and encoder readback
|
||||
time: 0 # Compensation delay [EtherCAT cycles]
|
||||
enable: true # Enable encoder delay compensation
|
||||
|
||||
controller: # Centralized ecmc position controller driving CSV velocity
|
||||
Kp: 0.06 # Proportional gain
|
||||
Ki: 0.04 # Integral gain
|
||||
Kd: 0.01 # Derivative gain
|
||||
Kff: 1
|
||||
|
||||
trajectory: # Trajectory-generator configuration
|
||||
type: 1 # Velocity profile: 0=trapezoidal; 1=S-curve (Ruckig)
|
||||
source: 0 # Position source: 0=axis trajectory generator; 1=PLC
|
||||
axis: # Normal-motion initialization values
|
||||
velocity: 3 # Default axis velocity [mm/s]
|
||||
acceleration: 2 # Default axis acceleration [mm/s^2]
|
||||
deceleration: 2 # Default axis deceleration [mm/s^2]
|
||||
emergencyDeceleration: 10 # Emergency deceleration [mm/s^2]
|
||||
jerk: 10 # S-curve jerk [mm/s^3]
|
||||
jog: # Jog-motion initialization values
|
||||
velocity: 1 # Default jog velocity [mm/s]
|
||||
|
||||
input: # Limit, home, and external-interlock inputs
|
||||
limit: # Hardware limit-switch inputs
|
||||
forward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.1 # EtherCAT forward-limit input
|
||||
backward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.0 # EtherCAT backward-limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Home input; constant true because no home sensor is used
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # External interlock; constant true because none is used
|
||||
|
||||
softlimits: # ecmc software travel-limit configuration
|
||||
enable: true # Globally enable software limits
|
||||
forward: 95 # Forward software-limit position [mm]
|
||||
forwardEnable: true # Enable the forward software limit
|
||||
backward: -1 # Backward software-limit position [mm]
|
||||
backwardEnable: true # Enable the backward software limit
|
||||
|
||||
monitoring: # Axis following-error, velocity, and in-position monitoring
|
||||
lag: # Position-lag/following-error monitoring
|
||||
enable: true # Enable position-lag monitoring
|
||||
tolerance: 0.5 # Maximum permitted position lag [mm]
|
||||
time: 10 # Allowed time outside lag tolerance [EtherCAT cycles]
|
||||
velocity: # Axis velocity monitoring
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 10 # Maximum permitted velocity [mm/s]
|
||||
time: # Allowed velocity-violation durations
|
||||
trajectory: 100 # Cycles before trajectory initialization is halted
|
||||
drive: 400 # Cycles before the drive is disabled
|
||||
target: # At-target/in-position monitoring
|
||||
enable: true # Enable at-target monitoring; required by the motor record
|
||||
tolerance: 0.002 # At-target position tolerance [mm]
|
||||
time: 50 # Required time inside tolerance [EtherCAT cycles]
|
||||
@@ -0,0 +1,158 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
@@ -0,0 +1,19 @@
|
||||
encoder: # ED7062 open-loop encoder configuration
|
||||
desc: 'Open loop' # Encoder description
|
||||
primary: false # Do not use this encoder as primary position feedback
|
||||
unit: mm # Encoder engineering unit
|
||||
numerator: 1 #500 # Encoder scaling numerator: stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 #2147483648 # Encoder scaling denominator: ED7062 counts per revolution
|
||||
type: 0 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 32 # Total raw encoder counter width [bits]
|
||||
absBits: 0 # Absolute-data width [bits]; zero for an incremental encoder
|
||||
absOffset: 0 # Absolute encoder offset in engineering units [mm]
|
||||
position: ec0.s$(DRV_SID).positionActual01 # EtherCAT ED7062 open-loop actual-position entry
|
||||
homing: # Referencing configuration for this incremental encoder
|
||||
refToEncIDAtStartup: 0 # At startup, reference to primary SSI encoder index 0
|
||||
type: 2 # Homing/reference sequence type
|
||||
position: 0 # Reference position in engineering units [mm]
|
||||
velocity: # Homing velocities
|
||||
to: 0.5 # Velocity toward the reference cam/sensor [mm/s]
|
||||
from: 0.25 # Velocity away from the reference cam/sensor [mm/s]
|
||||
useAsCSPDrvEnc: 1
|
||||
@@ -0,0 +1,203 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# For every posIndex, in forward and backward travel:
|
||||
# 1. Move to intermediatePos.
|
||||
# 2. Move to pos and measure/dwell only at pos.
|
||||
# intermediatePos is always smaller than pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=0.8000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=10.6900;pos:=10.8900;}
|
||||
if(posIndex==2){intermediatePos:=20.5775;pos:=20.7775;}
|
||||
if(posIndex==3){intermediatePos:=30.4675;pos:=30.6675;}
|
||||
if(posIndex==4){intermediatePos:=40.3550;pos:=40.5550;}
|
||||
if(posIndex==5){intermediatePos:=50.2450;pos:=50.4450;}
|
||||
if(posIndex==6){intermediatePos:=60.1325;pos:=60.3325;}
|
||||
if(posIndex==7){intermediatePos:=70.0225;pos:=70.2225;}
|
||||
if(posIndex==8){intermediatePos:=79.9100;pos:=80.1100;}
|
||||
if(posIndex==9){intermediatePos:=89.8000;pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,212 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 3;
|
||||
var ACC := 2;
|
||||
var DEC := 2;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 10;
|
||||
var N_POS := 20; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# Intermediate gap is disabled; intermediatePos equals pos.
|
||||
# Move to pos and measure/dwell at pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=1.0000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=1.0000;pos:=1.0000;}
|
||||
if(posIndex==2){intermediatePos:=6.0000;pos:=6.0000;}
|
||||
if(posIndex==3){intermediatePos:=11.0000;pos:=11.0000;}
|
||||
if(posIndex==4){intermediatePos:=16.0000;pos:=16.0000;}
|
||||
if(posIndex==5){intermediatePos:=21.0000;pos:=21.0000;}
|
||||
if(posIndex==6){intermediatePos:=26.0000;pos:=26.0000;}
|
||||
if(posIndex==7){intermediatePos:=31.0000;pos:=31.0000;}
|
||||
if(posIndex==8){intermediatePos:=36.0000;pos:=36.0000;}
|
||||
if(posIndex==9){intermediatePos:=41.0000;pos:=41.0000;}
|
||||
if(posIndex==10){intermediatePos:=46.0000;pos:=46.0000;}
|
||||
if(posIndex==11){intermediatePos:=51.0000;pos:=51.0000;}
|
||||
if(posIndex==12){intermediatePos:=56.0000;pos:=56.0000;}
|
||||
if(posIndex==13){intermediatePos:=61.0000;pos:=61.0000;}
|
||||
if(posIndex==14){intermediatePos:=66.0000;pos:=66.0000;}
|
||||
if(posIndex==15){intermediatePos:=71.0000;pos:=71.0000;}
|
||||
if(posIndex==16){intermediatePos:=76.0000;pos:=76.0000;}
|
||||
if(posIndex==17){intermediatePos:=81.0000;pos:=81.0000;}
|
||||
if(posIndex==18){intermediatePos:=86.0000;pos:=86.0000;}
|
||||
if(posIndex==19){intermediatePos:=86.0000;pos:=86.0000;}
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,66 @@
|
||||
# Script used to control the FAT stage in closed-loop CSV configuration with ED7062
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,true) # Override reset of EL5042
|
||||
|
||||
# EL2008 channel 4 supplies 24 V to the ED7062 limit switches
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=5,HW_DESC=EL2008"
|
||||
epicsEnvSet(BO_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
# ED7062 two-channel stepper drive in CSV mode (EtherCAT slave position 10)
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=10,HW_DESC=ED7062_CSP"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=1,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=1,MACROS='L_COIL_UH=45530,R_COIL_MOHM=15894,I_TI=29,I_KP=654,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#- Must tell ecmc that channel is not used
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2"
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml,DEV=${IOC},AX_NAME=M1,AXIS_ID=1,DRV_SID=${DRV_SID},ENC_SID=${ENC_SID},ENC_CH=01,BO_SID=${BO_SID}"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml,DEV=${IOC},ENC_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration
|
||||
# PLC code for Positioning
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/stopBeforePosition.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
# PLC code for Straightness Test
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/straightnessTest.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
|
||||
# Start motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
# Stop motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
@@ -0,0 +1,200 @@
|
||||
# OWIS stage with ED7062 CSV and TR SSI encoder
|
||||
|
||||
This folder configures the OWIS linear stage with an ED7062 two-channel stepper
|
||||
drive in cyclic synchronous velocity (CSV) mode. ECMC closes the position loop
|
||||
using the TR-Electronic LT140-S absolute SSI linear encoder. The configured
|
||||
engineering unit is millimetres.
|
||||
|
||||
The configuration was derived from `../EL7062_CSV`, but all drive declarations
|
||||
and descriptions in this folder refer to the ED7062.
|
||||
|
||||
## ED7062 declarations
|
||||
|
||||
| Setting | Configured value |
|
||||
| --- | --- |
|
||||
| Hardware description | `HW_DESC=ED7062` |
|
||||
| EtherCAT slave position | 10 |
|
||||
| Used channel | Channel 1 |
|
||||
| Unused channel | Channel 2, `Generic-Ch-Not-Used` |
|
||||
| Axis mode | `CSV` |
|
||||
| Drive setpoint | `velocitySetpoint01` |
|
||||
| Drive/control type | `1`, DS402/advanced drive |
|
||||
| Internal position | `positionActual01` |
|
||||
| Digital limit inputs | `binaryInputs01.0` and `.1` |
|
||||
|
||||
The declaration and PDO pattern follow PSI's ED7062 CSV example:
|
||||
|
||||
- [PSI EX7062/ED7062 CSV example](https://github.com/paulscherrerinstitute/ecmccfg/tree/b30e46072f900b37f7c674aee9a77b3c18f27735/examples/PSI/best_practice/motion/stepper_incremental/ex7062_CSV)
|
||||
- [PSI CSV/CSP/CSP-PC mode documentation](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/modes_csv_csp_csp_pc/)
|
||||
- [PSI axis YAML documentation](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/axisyaml/)
|
||||
|
||||
The copied EL7062-specific CSV firmware warning is intentionally not presented
|
||||
as an ED7062 fact. The files contain no evidence about the installed ED7062
|
||||
firmware; its disable/re-enable behaviour must still be checked on hardware.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, `EC_RATE=500` Hz |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS Stage ED7062` |
|
||||
| Stepper drive | ED7062 at EtherCAT slave 10, channel 1, CSV mode |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum, 0.5 A standby, 48 V nominal, 7.5 ohm/phase, 3080 uH, 400 full steps/revolution |
|
||||
| Primary feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Limit-switch supply | EL2008 slave 5, channel 4 switched output |
|
||||
| Position unit | mm |
|
||||
|
||||
## CSV drive scaling
|
||||
|
||||
The ED7062 CSV velocity setpoint uses a signed 32-bit range. With a stage travel
|
||||
of 1 mm/revolution and a 500 Hz EtherCAT rate:
|
||||
|
||||
```text
|
||||
drive.numerator = 1 mm/revolution * 500 cycles/second = 500
|
||||
drive.denominator = 2^31 = 2147483648
|
||||
|
||||
raw velocity = commanded velocity * 2147483648 / 500
|
||||
commanded velocity = raw velocity * 500 / 2147483648 mm/s
|
||||
```
|
||||
|
||||
At the configured default velocity of 3 mm/s, the nominal raw command is about
|
||||
`12884902` counts. Confirm the live setpoint and actual velocity during reduced-
|
||||
speed commissioning.
|
||||
|
||||
## Encoder configuration
|
||||
|
||||
### Primary SSI encoder
|
||||
|
||||
The EL5042 channel is configured by SDO before the axis is loaded:
|
||||
|
||||
- SSI mode, binary coding
|
||||
- 24 position bits, no multiturn or offset bits
|
||||
- Status bits disabled and CRC inversion enabled
|
||||
- 1 MHz clock
|
||||
- 9.0 V encoder supply
|
||||
- Scale: `1 / 10000 mm/count`, equivalent to `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Counter overflow/wraparound disabled
|
||||
|
||||
The `10000 counts/mm` value is labelled as interferometer-calibrated in
|
||||
`cfg/axis.yaml`. The files do not establish its calibration uncertainty or
|
||||
confirm the current mechanical datum.
|
||||
|
||||
### ED7062 internal counter
|
||||
|
||||
- Secondary encoder; the SSI encoder remains primary feedback
|
||||
- Scale: `1 / 1048576 mm/count` for a 1 mm/revolution stage
|
||||
- Incremental, 32-bit counter
|
||||
- Referenced to the primary SSI encoder at startup
|
||||
- Position PDO: `positionActual01`
|
||||
|
||||
## Position controller
|
||||
|
||||
In CSV mode, ECMC generates the trajectory and closes the position loop using
|
||||
the SSI encoder. The ED7062 closes its internal velocity and current loops.
|
||||
|
||||
The configured ECMC controller gains are:
|
||||
|
||||
| Parameter | Value |
|
||||
| --- | ---: |
|
||||
| `Kp` | 14 |
|
||||
| `Ki` | 1.6 |
|
||||
| `Kd` | 0.5 |
|
||||
| `Kff` | 1 |
|
||||
|
||||
These values differ substantially from the copied EL7062 configuration and are
|
||||
treated as local tuning values. Their origin and stability are not established
|
||||
by the files. Validate them at reduced current and velocity before normal motion.
|
||||
|
||||
## Motion and monitoring
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Trajectory profile | Trapezoidal (`type: 0`) |
|
||||
| Default velocity | 3 mm/s |
|
||||
| Default acceleration/deceleration | 2 mm/s^2 |
|
||||
| Emergency deceleration | 10 mm/s^2 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 10 mm/s |
|
||||
| Following-error tolerance | 0.5 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.002 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 10 s |
|
||||
| Automatic disable delay | 10 s idle |
|
||||
|
||||
The hardware limits use ED7062 channel 1 inputs:
|
||||
|
||||
- Backward limit: `binaryInputs01.0`
|
||||
- Forward limit: `binaryInputs01.1`
|
||||
- Limit-switch power: EL2008 channel 4
|
||||
|
||||
Home and external interlock are constant true because no corresponding sensors
|
||||
are assigned. Software limits and axis monitoring remain enabled.
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code_2.plc` at a 500 ms PLC sample period. A rising edge
|
||||
on `doMotion` starts the sequence.
|
||||
|
||||
- Move velocity: 2 mm/s
|
||||
- Acceleration and deceleration: 3 mm/s^2
|
||||
- Ten measurement positions from 1.0000 mm to 90.0000 mm
|
||||
- A preliminary position 0.2 mm below each measurement point
|
||||
- Intermediate dwell: 2 PLC scans, nominally 1 s
|
||||
- Measurement dwell: 12 PLC scans, nominally 6 s
|
||||
- Five forward/backward cycles
|
||||
|
||||
```sh
|
||||
# Start
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
|
||||
# Stop
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Remaining commissioning issues
|
||||
|
||||
- The motor component declares `R_COIL_MOHM=7500`, while the drive-controller
|
||||
component declares `R_COIL_MOHM=2471`. Resolve this mismatch before enabling
|
||||
motion. Use motor measurements and ED7062 autotune results for the installed
|
||||
motor rather than assuming the copied values are valid.
|
||||
- Confirm that `HW_DESC=ED7062` matches the installed device and the available
|
||||
`ecmccfg 11.0.8` hardware definition before starting the IOC.
|
||||
- Confirm the EL5042 output is 9.0 V and permitted by the exact encoder order
|
||||
code before connecting the encoder.
|
||||
- Confirm motor direction and SSI direction before closing the position loop. A
|
||||
sign error can command immediate motion in the wrong direction.
|
||||
- The PLC accepts busy-low plus `attarget` as move completion without first
|
||||
latching that busy became high. Validate or correct this handshake before
|
||||
unattended operation.
|
||||
- Static review does not prove PDO compatibility, controller stability, limit
|
||||
polarity, or safe operation on the target hardware.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EL5042 SDOs, ED7062 declaration, motor/controller components,
|
||||
axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - ED7062 CSV mapping, primary SSI feedback, trajectory,
|
||||
controller, limits, and monitoring
|
||||
- `cfg/enc_open_loop.yaml` - secondary ED7062 internal counter
|
||||
- `cfg/code_2.plc` - active FAT motion sequence
|
||||
- `cfg/code.plc` - alternate older sequence, not loaded by `startup.cmd`
|
||||
|
||||
## Commissioning sequence
|
||||
|
||||
1. Confirm that the IOC loads `ECMC/ED7062_CSV/startup.cmd`.
|
||||
2. Verify that EtherCAT slave 10 is the installed ED7062 and that channel 1 is
|
||||
connected to the motor while channel 2 is unused.
|
||||
3. Resolve the motor-resistance mismatch and run the appropriate drive autotune.
|
||||
4. Confirm 9.0 V at the EL5042 connector before attaching the encoder.
|
||||
5. With motion disabled, verify SSI readiness, position, status bits, ED7062
|
||||
counter, limit inputs, and limit-switch supply.
|
||||
6. Enable at reduced current and command a very low positive motion. Confirm
|
||||
motor direction, SSI direction, `velocitySetpoint01`, and actual velocity.
|
||||
7. Verify the 500/2147483648 CSV scaling against live setpoint and velocity.
|
||||
8. Tune and validate the ECMC position controller, following error, settling,
|
||||
software limits, and stop behaviour.
|
||||
9. Test disable/re-enable counter continuity on the installed ED7062 firmware.
|
||||
10. Validate the PLC execute/busy handshake before running the complete FAT
|
||||
sequence.
|
||||
@@ -0,0 +1,101 @@
|
||||
axis: # Physical-axis configuration
|
||||
id: ${AXIS_ID=1} # Unique numeric axis identifier
|
||||
feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=04} # EL2008 channel 4: 24 V supply for limit switches
|
||||
type: joint # Physical motor axis
|
||||
mode: CSV # ED7062 cyclic synchronous velocity mode
|
||||
autoEnable: # Native ecmc automatic axis enable/disable
|
||||
enableTimeout: 10 # Maximum time allowed to auto-enable [s]
|
||||
disableTimeout: 10 # Idle time before automatic disable [s]
|
||||
tweakDist: 1.0
|
||||
|
||||
plc: # Axis PLC configuration
|
||||
id: 1 # PLC identifier
|
||||
enable: yes # Enable the axis PLC
|
||||
externalCommands: true # Allow the PLC to issue axis commands
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1}
|
||||
precision: 3
|
||||
description: OWIS Stage ED7062
|
||||
unit: mm
|
||||
motorRecord:
|
||||
syncSoftLimits: False
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen'
|
||||
|
||||
|
||||
drive:
|
||||
numerator: 1 #500 # 1 mm/rev * 500 EtherCAT cycles/s
|
||||
denominator: 1048576 #2147483648 # Signed 32-bit ED7062 CSV velocity range
|
||||
type: 1 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).velocitySetpoint01 # ED7062 CSV velocity setpoint
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word EtherCAT entry
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word EtherCAT entry
|
||||
|
||||
|
||||
encoder: # Primary encoder configuration
|
||||
primary: true # Use this encoder as the primary feedback encoder
|
||||
desc: SSI # Encoder description: TR-Electronic LT140-S SSI
|
||||
numerator: 1 # Encoder scaling numerator [mm]
|
||||
denominator: 10000 # Interferometer-calibrated encoder scale [counts/mm]
|
||||
type: 1 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 24 # Total raw encoder data width [bits]
|
||||
absBits: 24 # Absolute-data width in the least-significant part of the raw value [bits]
|
||||
absOffset: -11.826 # Absolute encoder offset in engineering units [mm]
|
||||
allowOverUnderFlow: false # Disallow raw-counter wraparound for this linear encoder
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # EtherCAT encoder actual-position entry
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # EtherCAT encoder status-word entry; required by warning/error checks
|
||||
ready: 2 # Ready-bit index in the encoder status word
|
||||
warning: 0 # Warning-bit index in the encoder status word
|
||||
error: # Encoder-error bit indices in the status word; maximum three
|
||||
- 1 # Encoder error 0 bit
|
||||
delayComp: # Compensation for delay between setpoint output and encoder readback
|
||||
time: 0 # Compensation delay [EtherCAT cycles]
|
||||
enable: true # Enable encoder delay compensation
|
||||
|
||||
controller: # Centralized ecmc position controller driving CSV velocity
|
||||
Kp: 4 # Proportional gain
|
||||
Ki: 0.4 # Integral gain
|
||||
Kd: 0 # Derivative gain
|
||||
Kff: 1
|
||||
|
||||
trajectory: # Trajectory-generator configuration
|
||||
type: 1 # Velocity profile: 0=trapezoidal; 1=S-curve (Ruckig)
|
||||
source: 0 # Position source: 0=axis trajectory generator; 1=PLC
|
||||
axis: # Normal-motion initialization values
|
||||
velocity: 3 # Default axis velocity [mm/s]
|
||||
acceleration: 2 # Default axis acceleration [mm/s^2]
|
||||
deceleration: 2 # Default axis deceleration [mm/s^2]
|
||||
emergencyDeceleration: 10 # Emergency deceleration [mm/s^2]
|
||||
jerk: 10 # S-curve jerk [mm/s^3]
|
||||
jog: # Jog-motion initialization values
|
||||
velocity: 1 # Default jog velocity [mm/s]
|
||||
|
||||
input: # Limit, home, and external-interlock inputs
|
||||
limit: # Hardware limit-switch inputs
|
||||
forward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.1 # EtherCAT forward-limit input
|
||||
backward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.0 # EtherCAT backward-limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Home input; constant true because no home sensor is used
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # External interlock; constant true because none is used
|
||||
|
||||
softlimits: # ecmc software travel-limit configuration
|
||||
enable: true # Globally enable software limits
|
||||
forward: 95 # Forward software-limit position [mm]
|
||||
forwardEnable: true # Enable the forward software limit
|
||||
backward: -1 # Backward software-limit position [mm]
|
||||
backwardEnable: true # Enable the backward software limit
|
||||
|
||||
monitoring: # Axis following-error, velocity, and in-position monitoring
|
||||
lag: # Position-lag/following-error monitoring
|
||||
enable: true # Enable position-lag monitoring
|
||||
tolerance: 0.5 # Maximum permitted position lag [mm]
|
||||
time: 10 # Allowed time outside lag tolerance [EtherCAT cycles]
|
||||
velocity: # Axis velocity monitoring
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 10 # Maximum permitted velocity [mm/s]
|
||||
time: # Allowed velocity-violation durations
|
||||
trajectory: 100 # Cycles before trajectory initialization is halted
|
||||
drive: 400 # Cycles before the drive is disabled
|
||||
target: # At-target/in-position monitoring
|
||||
enable: true # Enable at-target monitoring; required by the motor record
|
||||
tolerance: 0.002 # At-target position tolerance [mm]
|
||||
time: 50 # Required time inside tolerance [EtherCAT cycles]
|
||||
@@ -0,0 +1,158 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
@@ -0,0 +1,203 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# For every posIndex, in forward and backward travel:
|
||||
# 1. Move to intermediatePos.
|
||||
# 2. Move to pos and measure/dwell only at pos.
|
||||
# intermediatePos is always smaller than pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=0.8000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=10.6900;pos:=10.8900;}
|
||||
if(posIndex==2){intermediatePos:=20.5775;pos:=20.7775;}
|
||||
if(posIndex==3){intermediatePos:=30.4675;pos:=30.6675;}
|
||||
if(posIndex==4){intermediatePos:=40.3550;pos:=40.5550;}
|
||||
if(posIndex==5){intermediatePos:=50.2450;pos:=50.4450;}
|
||||
if(posIndex==6){intermediatePos:=60.1325;pos:=60.3325;}
|
||||
if(posIndex==7){intermediatePos:=70.0225;pos:=70.2225;}
|
||||
if(posIndex==8){intermediatePos:=79.9100;pos:=80.1100;}
|
||||
if(posIndex==9){intermediatePos:=89.8000;pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
encoder: # ED7062 open-loop encoder configuration
|
||||
desc: 'Open loop' # Encoder description
|
||||
primary: false # Do not use this encoder as primary position feedback
|
||||
unit: mm # Encoder engineering unit
|
||||
numerator: 1 # 500 # Encoder scaling numerator: stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 #2147483648 # Encoder scaling denominator: ED7062 counts per revolution
|
||||
type: 0 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 32 # Total raw encoder counter width [bits]
|
||||
absBits: 0 # Absolute-data width [bits]; zero for an incremental encoder
|
||||
absOffset: 0 # Absolute encoder offset in engineering units [mm]
|
||||
position: ec0.s$(DRV_SID).positionActual01 # EtherCAT ED7062 open-loop actual-position entry
|
||||
homing: # Referencing configuration for this incremental encoder
|
||||
refToEncIDAtStartup: 0 # At startup, reference to primary SSI encoder index 0
|
||||
type: 2 # Homing/reference sequence type
|
||||
position: 0 # Reference position in engineering units [mm]
|
||||
velocity: # Homing velocities
|
||||
to: 0.5 # Velocity toward the reference cam/sensor [mm/s]
|
||||
from: 0.25 # Velocity away from the reference cam/sensor [mm/s]
|
||||
|
||||
@@ -0,0 +1,66 @@
|
||||
# Script used to control the FAT stage in closed-loop CSV configuration with ED7062
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2"
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,true) # Override reset of EL5042
|
||||
|
||||
# EL2008 channel 4 supplies 24 V to the ED7062 limit switches
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=5,HW_DESC=EL2008"
|
||||
epicsEnvSet(BO_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
# ED7062 two-channel stepper drive in CSV mode (EtherCAT slave position 10)
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=10,HW_DESC=ED7062"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=1,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=1,MACROS='L_COIL_UH=45530,R_COIL_MOHM=15894,I_TI=29,I_KP=654,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#- Must tell ecmc that channel is not used
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2"
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml,DEV=${IOC},AX_NAME=M1,AXIS_ID=1,DRV_SID=${DRV_SID},ENC_SID=${ENC_SID},ENC_CH=01,BO_SID=${BO_SID}"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml,DEV=${IOC},ENC_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/code_2.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
|
||||
# Start motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
# Stop motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
@@ -0,0 +1,168 @@
|
||||
# OWIS stage with EL7041 and TR SSI encoder
|
||||
|
||||
This folder contains the ECMC configuration used for the OWIS linear stage with
|
||||
an EL7041-0052 stepper terminal and a TR-Electronic LT140-S absolute linear
|
||||
encoder. The configured engineering unit is millimetres.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, master 0, `EC_RATE=500` |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS stage with TR SSI encoder` |
|
||||
| Stepper terminal | EL7041-0052 at EtherCAT slave 7, configured for CSV |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum current, 0.5 A standby current, 48 V nominal, 7.5 ohm/phase, 400 full steps/revolution |
|
||||
| Primary feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Position unit | mm |
|
||||
|
||||
The EL7041 distributed-clock configuration uses `ASSIGN_ACTIVATE=0x0300`, a
|
||||
2,000,000 ns Sync0 cycle, and zero Sync0 shift.
|
||||
|
||||
## Encoder and motion scaling
|
||||
|
||||
### Primary SSI encoder
|
||||
|
||||
The EL5042 channel is explicitly configured by SDO before the axis is loaded:
|
||||
|
||||
- SSI mode, binary coding
|
||||
- 24 position bits, no multiturn or offset bits
|
||||
- Status bits disabled and CRC inversion enabled
|
||||
- 1 MHz clock
|
||||
- 9.0 V encoder supply
|
||||
- Scale: `1 / 10000 mm/count`, equivalent to `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Counter overflow/wraparound disabled
|
||||
|
||||
The `10000 counts/mm` value is described in `cfg/axis.yaml` as the measured
|
||||
encoder scale. These files do not independently establish the calibration
|
||||
uncertainty or confirm the current mechanical datum.
|
||||
|
||||
### EL7041 drive and open-loop counter
|
||||
|
||||
- CSV velocity scaling: `5 / 32768 mm/s` per raw setpoint unit
|
||||
- The source comment identifies 5 mm/s as 2000 full steps/s at 400 steps/mm.
|
||||
- Open-loop scale: `1 / 25600 mm/count`
|
||||
- Open-loop position width: 16 bits
|
||||
- The open-loop encoder is secondary; the SSI encoder is primary feedback.
|
||||
- At startup, the open-loop encoder references encoder ID 1.
|
||||
|
||||
## Axis behaviour
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Default velocity | 2 mm/s |
|
||||
| Default acceleration/deceleration | 3 mm/s^2 |
|
||||
| Emergency deceleration | 5 mm/s^2 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 3 mm/s |
|
||||
| Following-error tolerance | 0.05 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.0015 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 15 s |
|
||||
| Automatic disable delay | 15 s idle |
|
||||
|
||||
The trajectory generator is configured for an S-curve profile. Automatic
|
||||
enable at startup is disabled, and the EPICS motor record is disabled in this
|
||||
axis configuration. External axis commands remain enabled.
|
||||
|
||||
The external interlock and home inputs are constant true because no external
|
||||
interlock or home sensor is assigned. The hardware limits are read from the
|
||||
EL7041 drive status word:
|
||||
|
||||
- Backward limit: `driveStatus01.11`
|
||||
- Forward limit: `driveStatus01.12`
|
||||
|
||||
## Controller configuration
|
||||
|
||||
ECMC uses the TR SSI encoder as the primary position feedback and applies these
|
||||
controller values from `cfg/axis.yaml`:
|
||||
|
||||
| Parameter | Value |
|
||||
| --- | ---: |
|
||||
| `Kp` | 1 |
|
||||
| `Ki` | 0.1 |
|
||||
| `Kd` | 1.5 |
|
||||
| `Kff` | 1 |
|
||||
|
||||
These are configured values; the files do not show when or how they were tuned.
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code.plc` at a 500 ms PLC sample period. A rising edge
|
||||
on the `doMotion` variable starts the sequence.
|
||||
|
||||
The sequence uses:
|
||||
|
||||
- Move velocity: 2 mm/s
|
||||
- Acceleration and deceleration: 2 mm/s^2
|
||||
- Ten positions from 1.0000 mm to 90.0000 mm
|
||||
- Dwell: 12 PLC scans, nominally 6 s at each position
|
||||
- Five forward/backward cycles
|
||||
|
||||
The configured positions are:
|
||||
|
||||
```text
|
||||
1.0000 mm
|
||||
10.8575 mm
|
||||
20.1050 mm
|
||||
31.8050 mm
|
||||
38.3275 mm
|
||||
51.9900 mm
|
||||
57.6875 mm
|
||||
71.4650 mm
|
||||
81.2450 mm
|
||||
90.0000 mm
|
||||
```
|
||||
|
||||
The PLC powers off the axis and disables itself if either limit becomes invalid
|
||||
or `mc_move_abs()` returns an error.
|
||||
|
||||
Start and stop commands documented by `startup.cmd` are:
|
||||
|
||||
```sh
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Configuration caveats
|
||||
|
||||
- `ECMC_SLAVE_RESET` is set to `false` before the EL5042 is added and remains
|
||||
`false` after its SDO configuration. Confirm that retaining this reset override
|
||||
is intentional for the installed terminal and startup procedure.
|
||||
- No limit-switch feed-output mapping is enabled in `cfg/axis.yaml`; the
|
||||
`feedSwitchesOutput` line is commented out.
|
||||
- The PLC considers a move complete whenever drive busy is low and `attarget` is
|
||||
true; it does not first latch that drive busy became high. Confirm this
|
||||
execute/busy behaviour with the installed ECMC helper before relying on the
|
||||
unattended sequence.
|
||||
- The 16-bit open-loop counter and its overflow behaviour should be checked over
|
||||
the required travel. No explicit overflow setting is present in
|
||||
`cfg/enc_open_loop.yaml`.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EtherCAT slave setup, EL5042 SDOs, EL7041 motor component,
|
||||
distributed clocks, axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - axis, primary encoder, limits, trajectory, controller, and
|
||||
monitoring configuration
|
||||
- `cfg/enc_open_loop.yaml` - EL7041 secondary/open-loop encoder configuration
|
||||
- `cfg/code.plc` - active multi-position FAT sequence
|
||||
|
||||
## Checks required before operation
|
||||
|
||||
1. Verify the loaded IOC working directory and confirm that this `startup.cmd`
|
||||
and `cfg/code.plc` are the active files.
|
||||
2. Verify EL7041 channel assignment, motor phase wiring, phase resistance,
|
||||
configured currents, and controller tuning.
|
||||
3. Confirm the EL5042 output voltage is 9.0 V before connecting the encoder, and
|
||||
verify the encoder's permitted supply voltage from its documentation.
|
||||
4. Confirm that the encoder is ready and has no warning or error bits.
|
||||
5. Confirm that positive motor motion produces positive SSI position motion.
|
||||
6. Verify the encoder scale and absolute offset against a traceable displacement
|
||||
reference if the encoder or stage datum has changed.
|
||||
7. Exercise both hardware limit switches at low velocity and confirm their raw
|
||||
status bits and configured directions.
|
||||
8. Validate following error, settling, software limits, open-loop counter
|
||||
behaviour, and the PLC move handshake at reduced speed before running the
|
||||
complete automatic sequence.
|
||||
@@ -0,0 +1,109 @@
|
||||
axis:
|
||||
id: ${AXIS_ID=1} # Axis id
|
||||
type: joint # Physical motor axis
|
||||
mode: CSV # EL7041 velocity setpoint mode
|
||||
#feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=01} # Ethercat entry for feed switches
|
||||
autoEnable:
|
||||
enableTimeout: 15.0
|
||||
disableTimeout: 15.0
|
||||
atStartup: false # Enable only when motion is requested
|
||||
tweakDist: 1.0
|
||||
|
||||
plc:
|
||||
id: 1
|
||||
enable: true
|
||||
externalCommands: true
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1} # Axis name
|
||||
precision: 3 # Decimal count
|
||||
description: OWIS stage with TR SSI encoder # Axis description
|
||||
unit: mm # Unit
|
||||
motorRecord:
|
||||
enable: false
|
||||
description: OWIS stage with TR SSI encoder
|
||||
syncSoftLimits: false
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen' # Extra config for Motor record
|
||||
|
||||
drive:
|
||||
numerator: 5 # 2000 full-steps/s at 400 steps/mm = 5 mm/s
|
||||
denominator: 32768 # I/O range for ECMC_EC_ALIAS_DRV_VELO_SET (normally +-16bit)
|
||||
type: 0 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).velocitySetpoint01 # Velocity setpoint if CSV. Position setpoint if CSP
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word ethercat entry
|
||||
enable: 0 # Enable bit index in control word (not used if DS402)
|
||||
reset: 1 # Reset bit in control word (if no drive reset bit then leave empty)
|
||||
reduceTorque: 2 # Reduce torque bit in drive control word
|
||||
reduceTorqueEnable: true # Enable reduce torque functionality
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word ethercat entry
|
||||
enabled: 1 # Enabled bit index in status word (not used if DS402)
|
||||
warning: 2 # Warning bit in status word (if no drive warning bit then leave empty)
|
||||
error: # max 3 error bits in status word
|
||||
- 3 # Error 0 (if no drive error bit then leave empty)
|
||||
- 7 # Error 1 (if no drive error bit then leave empty)
|
||||
- 14 # Error 2 (if no drive error bit then leave empty)
|
||||
|
||||
encoder:
|
||||
source: 0 # Encoder value from EtherCAT hardware
|
||||
desc: SSI
|
||||
primary: true
|
||||
numerator: 1 # Engineering-unit numerator in mm
|
||||
denominator: 10000 # Measured encoder counts per mm
|
||||
type: 1 # Type: 0=Incremental, 1=Absolute
|
||||
bits: 24 # Total bit count of encoder raw data
|
||||
absBits: 24 # Absolute bit count (for absolute encoders) always least significant part of 'bits'
|
||||
absOffset: -11.826 # Absolute encoder offset in mm
|
||||
allowOverUnderFlow: false # Linear encoder: do not wrap at raw-count limits
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # Ethercat entry for actual position input (encoder)
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # mandatory only if 'warning' or 'error' are used
|
||||
ready: 2 # Bit in encoder status word for encoder ready
|
||||
warning: 0 # Warning (optional)
|
||||
error: # max 3 (optional)
|
||||
- 1 # Error 0
|
||||
|
||||
controller:
|
||||
Kp: 1 # Proportional gain
|
||||
Ki: 0.1 # Ki integral gain
|
||||
Kd: 1.5 # Kd derivative gain
|
||||
Kff: 1 # Feed-forward gain
|
||||
|
||||
trajectory:
|
||||
type: 1 # 0 = trapezoidal, 1 = S-curve (Ruckig)
|
||||
source: 0 # 0 = take trajectory setpoint from axis traj object, 1 =trajectory setpoint from plc
|
||||
axis:
|
||||
velocity: 2 # Default velo for axis
|
||||
acceleration: 3 # Default acc for axis
|
||||
deceleration: 3 # Default dec for axis
|
||||
emergencyDeceleration: 5 # Deceleration when axis in error state
|
||||
jog:
|
||||
velocity: 1 # Default motor-record jog velocity
|
||||
|
||||
input:
|
||||
limit:
|
||||
forward: ec0.s$(DRV_SID).driveStatus01.12 # EL7041 forward limit input
|
||||
backward: ec0.s$(DRV_SID).driveStatus01.11 # EL7041 backward limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Ethercat entry for home switch
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # Ethercat entry for interlock switch input
|
||||
|
||||
softlimits:
|
||||
enable: true # Enable soft limits
|
||||
forward: 95.0 # Soft limit position fwd
|
||||
forwardEnable: true # Soft limit position fwd enable
|
||||
backward: -1.0 # Soft limit position bwd
|
||||
backwardEnable: true # Soft limit position bwd enable
|
||||
|
||||
monitoring:
|
||||
lag:
|
||||
enable: true # Enable position lag monitoring (following error)
|
||||
tolerance: 0.05 # Allowed tolerance
|
||||
time: 10 # Allowed time outside tolerance target:
|
||||
velocity:
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 3 # Allowed max velocity
|
||||
time:
|
||||
trajectory: 100 # Time allowed outside max velo before system init halt
|
||||
drive: 400 # Time allowed outside max velo before system disables drive
|
||||
target:
|
||||
enable: true # Enable at target monitoring (needs to be enabled if using motor record)
|
||||
tolerance: 0.0015 # Allowed tolerance
|
||||
time: 50 # Filter time inside tolerance to be at target
|
||||
@@ -0,0 +1,156 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 2;
|
||||
var DEC := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
@@ -0,0 +1,20 @@
|
||||
encoder:
|
||||
#source: 1
|
||||
desc: 'Open loop'
|
||||
primary: false
|
||||
unit: mm
|
||||
numerator: 1 # Scaling numerator
|
||||
denominator: 25600 #12800 # Scaling denominator
|
||||
type: 0 # Type: 0=Incremental, 1=Absolute
|
||||
bits: 16 # Total bit count of encoder raw data
|
||||
absBits: 0 # Absolute bit count (for absolute encoders)
|
||||
absOffset: 0 #0.036 # Encoder offset in eng units (for absolute encoders)
|
||||
position: ec0.s$(DRV_SID).positionActual01 # Ethercat entry for actual position input (encoder)
|
||||
homing:
|
||||
refToEncIDAtStartup: 0 # Ref encoder at startup (to BISS value)
|
||||
type: 2
|
||||
position: 0
|
||||
velocity:
|
||||
to: 0.5
|
||||
from: 0.25
|
||||
|
||||
@@ -0,0 +1,63 @@
|
||||
##############################################################################
|
||||
## FAT Absolute Linear Encoder
|
||||
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1,MASTER_ID=0, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
# -------------------------------------------------------------------------------------
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL7041 1Ch Stepper
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=7,HW_DESC=EL7041-0052"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper, MACROS='I_MAX_MA=800, I_STDBY_MA=500, U_NOM_MV=48000, R_COIL_MOHM=7500, STEPS=400' "
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applySlaveDCconfig.cmd \
|
||||
"ASSIGN_ACTIVATE=0x0300,SYNC_0_CYCLE=2000000,SYNC_0_SHIFT=0"
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml, DEV=${IOC}, AX_NAME=M1, AXIS_ID=1, DRV_SID=${DRV_SID}, ENC_SID=${ENC_SID}, ENC_CH=01"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml, DEV=${IOC}, DRV_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration --------------------------------------
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd, "FILE=./cfg/code.plc, DESC='Position sequence', SAMPLE_RATE_MS=500, PLC_MACROS='AX_ID=1'"
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
#PLC_ID=0,
|
||||
# Start motion with " caput aik-motion-pc5:Set-M1-DoMtn-RB 1 "
|
||||
# Stop motion with " caput aik-motion-pc5:Set-M1-DoMtn-RB 0 "
|
||||
@@ -0,0 +1,161 @@
|
||||
# OWIS stage with EL7062 and TR SSI encoder
|
||||
|
||||
This folder contains the ECMC configuration used for the OWIS linear stage with
|
||||
an EL7062 stepper terminal and a TR-Electronic LT140-S absolute linear encoder.
|
||||
The configured engineering unit is millimetres.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, `EC_RATE=500` |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS Stage EL7062` |
|
||||
| Stepper terminal | EL7062 at EtherCAT slave 10, configured for CSP |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum current, 0.5 A standby current, 48 V nominal, 7.5 ohm/phase, 3080 uH, 400 full steps/revolution |
|
||||
| Primary feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Limit-switch supply | EL2008 slave 5, channel 4 switched output |
|
||||
| Position unit | mm |
|
||||
|
||||
`startup.cmd` currently applies motor and controller components to EL7062
|
||||
channels 1 and 2. Axis `M1` uses channel 1 EtherCAT entries; no axis is loaded
|
||||
for channel 2 in this folder.
|
||||
|
||||
## Encoder and motion scaling
|
||||
|
||||
### Primary SSI encoder
|
||||
|
||||
The EL5042 channel is explicitly configured by SDO before the axis is loaded:
|
||||
|
||||
- SSI mode, binary coding
|
||||
- 24 position bits, no multiturn or offset bits
|
||||
- Status bits disabled and CRC inversion enabled
|
||||
- 1 MHz clock
|
||||
- 9.0 V encoder supply
|
||||
- Scale: `1 / 10000 mm/count`, equivalent to `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Counter overflow/wraparound disabled
|
||||
|
||||
The `10000 counts/mm` value is documented in `cfg/axis.yaml` as the
|
||||
interferometer-calibrated scale. The README does not independently validate that
|
||||
calibration or the current mechanical datum.
|
||||
|
||||
### EL7062 position interface and open-loop counter
|
||||
|
||||
- Stage travel used for scaling: `1 mm/revolution`
|
||||
- EL7062 CSP scale: `1048576 counts/revolution`
|
||||
- Open-loop position width: 32 bits
|
||||
- The open-loop encoder is secondary; the SSI encoder is primary feedback.
|
||||
- At startup, the open-loop encoder references encoder ID 1.
|
||||
- `useAsCSPDrvEnc: 1` selects it as the CSP drive encoder.
|
||||
|
||||
## Axis behaviour
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Default velocity | 3 mm/s |
|
||||
| Default acceleration/deceleration | 1 mm/s^2 |
|
||||
| Emergency deceleration | 10 mm/s^2 |
|
||||
| S-curve jerk | 10 mm/s^3 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 6 mm/s |
|
||||
| Following-error tolerance | 0.05 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.0015 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 10 s |
|
||||
| Automatic disable delay | 60 s idle |
|
||||
|
||||
The trajectory generator is configured for an S-curve profile. The external
|
||||
interlock and home inputs are constant true in this configuration because no
|
||||
external interlock or home sensor is assigned.
|
||||
|
||||
The hardware limits use EL7062 channel 1 digital inputs:
|
||||
|
||||
- Backward limit: `binaryInputs01.0`
|
||||
- Forward limit: `binaryInputs01.1`
|
||||
- Limit-switch power: EL2008 channel 4
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code_2.plc` at a 500 ms PLC sample period. A rising edge
|
||||
on the `doMotion` variable starts the sequence.
|
||||
|
||||
The active sequence uses:
|
||||
|
||||
- Move velocity: 2 mm/s
|
||||
- Acceleration and deceleration: 3 mm/s^2
|
||||
- Ten measurement positions from 1.0000 mm to 90.0000 mm
|
||||
- A preliminary position 0.2 mm below every measurement position so the final
|
||||
approach is always in the positive direction
|
||||
- Intermediate dwell: 2 PLC scans, nominally 1 s
|
||||
- Measurement dwell: 12 PLC scans, nominally 6 s
|
||||
- Five forward/backward cycles
|
||||
|
||||
The ten `(preliminary -> measurement)` position pairs are:
|
||||
|
||||
```text
|
||||
0.8000 -> 1.0000 mm
|
||||
10.6900 -> 10.8900 mm
|
||||
20.5775 -> 20.7775 mm
|
||||
30.4675 -> 30.6675 mm
|
||||
40.3550 -> 40.5550 mm
|
||||
50.2450 -> 50.4450 mm
|
||||
60.1325 -> 60.3325 mm
|
||||
70.0225 -> 70.2225 mm
|
||||
79.9100 -> 80.1100 mm
|
||||
89.8000 -> 90.0000 mm
|
||||
```
|
||||
|
||||
The PLC powers off the axis and disables itself if either limit becomes invalid
|
||||
or `mc_move_abs()` returns an error.
|
||||
|
||||
Start and stop commands documented by `startup.cmd` are:
|
||||
|
||||
```sh
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Configuration caveats
|
||||
|
||||
- The motor component declares `R_COIL_MOHM=7500`, while the controller
|
||||
component declares `R_COIL_MOHM=2471`. Confirm which resistance belongs to
|
||||
the installed motor before commissioning or retuning the drive.
|
||||
- The controller gains and `L_COIL_UH=3080` are configuration values only. The
|
||||
files do not provide evidence that they were measured, autotuned, or validated
|
||||
on the currently connected hardware.
|
||||
- The PLC considers a move complete whenever drive busy is low and `attarget` is
|
||||
true; it does not first latch that drive busy became high. Confirm this
|
||||
execute/busy behaviour with the installed ECMC helper before relying on the
|
||||
unattended sequence.
|
||||
- Comments in the source contain a few stale labels (for example, CSV wording
|
||||
beside the CSP slave configuration). The executable setting is
|
||||
`HW_DESC=EL7062_CSP` and the axis mode is `CSP`.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EtherCAT slave setup, EL5042 SDOs, motor/controller components,
|
||||
axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - axis, primary encoder, limits, trajectory, controller, and
|
||||
monitoring configuration
|
||||
- `cfg/enc_open_loop.yaml` - EL7062 secondary/open-loop encoder configuration
|
||||
- `cfg/code_2.plc` - active multi-position FAT sequence
|
||||
- `cfg/code.plc` - alternate older position sequence; not loaded by
|
||||
`startup.cmd`
|
||||
|
||||
## Checks required before operation
|
||||
|
||||
1. Verify the loaded IOC working directory and confirm that this `startup.cmd`
|
||||
and `cfg/code_2.plc` are the active files.
|
||||
2. Verify EL7062 channel assignment, motor phase wiring, phase resistance, phase
|
||||
inductance, configured currents, and controller tuning.
|
||||
3. Confirm the EL5042 output voltage is 9.0 V before connecting the encoder, and
|
||||
verify the encoder's permitted supply voltage from its documentation.
|
||||
4. Confirm that the encoder is ready and has no warning or error bits.
|
||||
5. Confirm that positive motor motion produces positive SSI position motion.
|
||||
6. Verify the encoder scale and absolute offset against a traceable displacement
|
||||
reference if the encoder or stage datum has changed.
|
||||
7. Exercise both hardware limit switches at low velocity and confirm their raw
|
||||
input states and configured directions.
|
||||
8. Validate following error, settling, software limits, and the PLC move
|
||||
handshake at reduced speed before running the complete automatic sequence.
|
||||
@@ -0,0 +1,105 @@
|
||||
axis: # Physical-axis configuration
|
||||
id: ${AXIS_ID=1} # Unique numeric axis identifier
|
||||
feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=04} # EL2008 channel 4: 24 V supply for limit switches
|
||||
type: joint # Physical motor axis
|
||||
mode: CSP # EL7062 cyclic synchronous velocity mode
|
||||
autoEnable: # Native ecmc automatic axis enable/disable
|
||||
enableTimeout: 10 # Maximum time allowed to auto-enable [s]
|
||||
disableTimeout: 10 # Idle time before automatic disable [s]
|
||||
tweakDist: 1.0
|
||||
|
||||
plc: # Axis PLC configuration
|
||||
id: 1 # PLC identifier
|
||||
enable: yes # Enable the axis PLC
|
||||
externalCommands: true # Allow the PLC to issue axis commands
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1}
|
||||
precision: 3
|
||||
description: OWIS Stage EL7062
|
||||
unit: mm
|
||||
motorRecord:
|
||||
syncSoftLimits: False
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen'
|
||||
|
||||
|
||||
drive:
|
||||
numerator: 1 # Fastest speed in eng. units (1mm/s*8000Hz)
|
||||
denominator: 1048576 # I/O range for ECMC_EC_ALIAS_DRV_VELO_SET (normally +-16bit)
|
||||
type: 1 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).positionSetpoint01 #ec0.s$(DRV_SID).positionSetpoint${DRV_CH=01}
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word EtherCAT entry
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word EtherCAT entry
|
||||
warning: 2 # Warning bit in status word (if no drive warning bit then leave empty)
|
||||
error: # max 3 error bits in status word
|
||||
- 3 # Error 0 (if no drive error bit then leave empty)
|
||||
- 7 # Error 1 (if no drive error bit then leave empty)
|
||||
- 14 # Error 2 (if no drive error bit then leave empty)
|
||||
|
||||
encoder: # Primary encoder configuration
|
||||
primary: true # Use this encoder as the primary feedback encoder
|
||||
desc: SSI # Encoder description: TR-Electronic LT140-S SSI
|
||||
numerator: 1 # Encoder scaling numerator [mm]
|
||||
denominator: 10000 # Interferometer-calibrated encoder scale [counts/mm]
|
||||
type: 1 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 24 # Total raw encoder data width [bits]
|
||||
absBits: 24 # Absolute-data width in the least-significant part of the raw value [bits]
|
||||
absOffset: -11.826 # Absolute encoder offset in engineering units [mm]
|
||||
allowOverUnderFlow: false # Disallow raw-counter wraparound for this linear encoder
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # EtherCAT encoder actual-position entry
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # EtherCAT encoder status-word entry; required by warning/error checks
|
||||
ready: 2 # Ready-bit index in the encoder status word
|
||||
warning: 0 # Warning-bit index in the encoder status word
|
||||
error: # Encoder-error bit indices in the status word; maximum three
|
||||
- 1 # Encoder error 0 bit
|
||||
delayComp: # Compensation for delay between setpoint output and encoder readback
|
||||
time: 0 # Compensation delay [EtherCAT cycles]
|
||||
enable: true # Enable encoder delay compensation
|
||||
|
||||
controller: # Centralized ecmc PID controller for CSP-PC operation
|
||||
Kp: 0.02 # Proportional gain
|
||||
Ki: 0.01 # Integral gain
|
||||
Kd: 0.01 # Derivative gain
|
||||
Kff: 1
|
||||
|
||||
trajectory: # Trajectory-generator configuration
|
||||
type: 1 # Velocity profile: 0=trapezoidal; 1=S-curve (Ruckig)
|
||||
source: 0 # Position source: 0=axis trajectory generator; 1=PLC
|
||||
axis: # Normal-motion initialization values
|
||||
velocity: 2 # Default axis velocity [mm/s]
|
||||
acceleration: 2 # Default axis acceleration [mm/s^2]
|
||||
deceleration: 2 # Default axis deceleration [mm/s^2]
|
||||
emergencyDeceleration: 10 # Emergency deceleration [mm/s^2]
|
||||
jerk: 10 # S-curve jerk [mm/s^3]
|
||||
jog: # Jog-motion initialization values
|
||||
velocity: 1 # Default jog velocity [mm/s]
|
||||
|
||||
input: # Limit, home, and external-interlock inputs
|
||||
limit: # Hardware limit-switch inputs
|
||||
forward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.1 # EtherCAT forward-limit input
|
||||
backward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.0 # EtherCAT backward-limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Home input; constant true because no home sensor is used
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # External interlock; constant true because none is used
|
||||
|
||||
softlimits: # ecmc software travel-limit configuration
|
||||
enable: true # Globally enable software limits
|
||||
forward: 95 # Forward software-limit position [mm]
|
||||
forwardEnable: true # Enable the forward software limit
|
||||
backward: -1 # Backward software-limit position [mm]
|
||||
backwardEnable: true # Enable the backward software limit
|
||||
|
||||
monitoring: # Axis following-error, velocity, and in-position monitoring
|
||||
lag: # Position-lag/following-error monitoring
|
||||
enable: true # Enable position-lag monitoring
|
||||
tolerance: 0.05 # Maximum permitted position lag [mm]
|
||||
time: 10 # Allowed time outside lag tolerance [EtherCAT cycles]
|
||||
velocity: # Axis velocity monitoring
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 3 # Maximum permitted velocity [mm/s]
|
||||
time: # Allowed velocity-violation durations
|
||||
trajectory: 100 # Cycles before trajectory initialization is halted
|
||||
drive: 400 # Cycles before the drive is disabled
|
||||
target: # At-target/in-position monitoring
|
||||
enable: true # Enable at-target monitoring; required by the motor record
|
||||
tolerance: 0.0015 # At-target position tolerance [mm]
|
||||
time: 50 # Required time inside tolerance [EtherCAT cycles]
|
||||
@@ -0,0 +1,158 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
@@ -0,0 +1,203 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# For every posIndex, in forward and backward travel:
|
||||
# 1. Move to intermediatePos.
|
||||
# 2. Move to pos and measure/dwell only at pos.
|
||||
# intermediatePos is always smaller than pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=0.8000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=10.6900;pos:=10.8900;}
|
||||
if(posIndex==2){intermediatePos:=20.5775;pos:=20.7775;}
|
||||
if(posIndex==3){intermediatePos:=30.4675;pos:=30.6675;}
|
||||
if(posIndex==4){intermediatePos:=40.3550;pos:=40.5550;}
|
||||
if(posIndex==5){intermediatePos:=50.2450;pos:=50.4450;}
|
||||
if(posIndex==6){intermediatePos:=60.1325;pos:=60.3325;}
|
||||
if(posIndex==7){intermediatePos:=70.0225;pos:=70.2225;}
|
||||
if(posIndex==8){intermediatePos:=79.9100;pos:=80.1100;}
|
||||
if(posIndex==9){intermediatePos:=89.8000;pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
encoder: # EL7062 open-loop encoder configuration
|
||||
desc: 'Open loop' # Encoder description
|
||||
primary: false # Do not use this encoder as primary position feedback
|
||||
unit: mm # Encoder engineering unit
|
||||
numerator: 1 # Encoder scaling numerator: stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 # Encoder scaling denominator: EL7062 CSP units per revolution
|
||||
type: 0 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 32 # Total raw encoder counter width [bits]
|
||||
absBits: 0 # Absolute-data width [bits]; zero for an incremental encoder
|
||||
absOffset: 0 # Absolute encoder offset in engineering units [mm]
|
||||
position: ec0.s$(DRV_SID).positionActual01 # EtherCAT EL7062 open-loop actual-position entry
|
||||
homing: # Referencing configuration for this incremental encoder
|
||||
refToEncIDAtStartup: 0 # At startup, reference to the actual position of encoder ID 1
|
||||
type: 2 # Homing/reference sequence type
|
||||
position: 0 # Reference position in engineering units [mm]
|
||||
velocity: # Homing velocities
|
||||
to: 0.5 # Velocity toward the reference cam/sensor [mm/s]
|
||||
from: 0.25 # Velocity away from the reference cam/sensor [mm/s]
|
||||
useAsCSPDrvEnc: 1
|
||||
|
||||
@@ -0,0 +1,65 @@
|
||||
# Script used to control the FAT stage in closed-loop configuration with EL7062
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,true) # Override reset of EL5042
|
||||
|
||||
# EL2008 channel 4 supplies 24 V to the EL7062 limit switches
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=5,HW_DESC=EL2008"
|
||||
epicsEnvSet(BO_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
# EL7062 1-channel stepper drive in CSV mode (EtherCAT slave position 10)
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=10,HW_DESC=EL7062_CSP"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=1,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=1,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=2,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=2,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#- Must tell ecmc that channel 02 is not used
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2'"
|
||||
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml,DEV=${IOC},AX_NAME=M1,AXIS_ID=1,DRV_SID=${DRV_SID},ENC_SID=${ENC_SID},ENC_CH=01,BO_SID=${BO_SID}"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml,DEV=${IOC},ENC_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/code_2.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
|
||||
# Start motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
# Stop motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
@@ -0,0 +1,201 @@
|
||||
# OWIS stage with EL7062 CSP-PC and TR SSI encoder
|
||||
|
||||
This folder configures the OWIS linear stage in **CSP-PC** mode: cyclic
|
||||
synchronous position with dual position loops. The EL7062 closes its inner
|
||||
position loop using its internal motor-position counter, while ECMC closes an
|
||||
outer position loop using the TR-Electronic LT140-S absolute SSI linear encoder.
|
||||
|
||||
The engineering unit for the drive and both encoders is millimetres.
|
||||
|
||||
## How CSP-PC is selected
|
||||
|
||||
ECMC does not use a separate `mode: CSP_PC` YAML value. PSI documents CSP-PC as
|
||||
this combination:
|
||||
|
||||
1. Load the CSP PDO layout with `HW_DESC=EL7062_CSP`.
|
||||
2. Set the axis to `mode: CSP`.
|
||||
3. Map `positionSetpoint01` as the drive setpoint.
|
||||
4. Define the external SSI encoder as the primary encoder.
|
||||
5. Define the EL7062 internal position counter as a secondary encoder and set
|
||||
`useAsCSPDrvEnc: 1`.
|
||||
6. Configure and tune the ECMC controller for the outer position loop.
|
||||
|
||||
The defining local settings are:
|
||||
|
||||
```text
|
||||
startup.cmd: HW_DESC=EL7062_CSP
|
||||
cfg/axis.yaml: mode: CSP
|
||||
cfg/axis.yaml: setpoint: ...positionSetpoint01
|
||||
cfg/axis.yaml: primary: true # TR SSI encoder
|
||||
cfg/enc_open_loop.yaml: useAsCSPDrvEnc: 1 # EL7062 drive encoder
|
||||
```
|
||||
|
||||
References:
|
||||
|
||||
- [PSI drive modes: CSV, CSP, and CSP-PC](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/modes_csv_csp_csp_pc/)
|
||||
- [PSI EL7062/EL5042 best-practice example](https://github.com/paulscherrerinstitute/ecmccfg/tree/master/examples/PSI/best_practice/motion/stepper_bissc/el7062_el5042)
|
||||
- [PSI axis YAML controller documentation](https://paulscherrerinstitute.github.io/ecmccfg/manual/motion_cfg/axisyaml/)
|
||||
- [PSI tuning guidance](https://paulscherrerinstitute.github.io/ecmccfg/manual/knowledgebase/tuning/)
|
||||
|
||||
## Control-loop ownership
|
||||
|
||||
| Function | Location | Feedback or command |
|
||||
| --- | --- | --- |
|
||||
| Trajectory generation | ECMC | Position trajectory in mm |
|
||||
| Outer position loop | ECMC | TR SSI position versus trajectory position |
|
||||
| Inner position loop | EL7062 | EL7062 internal motor-position counter versus CSP setpoint |
|
||||
| Velocity loop | EL7062 | Drive internal |
|
||||
| Current loop | EL7062 | Drive internal |
|
||||
|
||||
ECMC adjusts the CSP position command sent to the EL7062 to correct the error
|
||||
measured by the external SSI encoder. This is the dual-position-loop behaviour
|
||||
shown in the supplied CSP-PC diagram.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, `EC_RATE=500` Hz |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS Stage EL7062 CSP-PC` |
|
||||
| Stepper terminal | EL7062 at EtherCAT slave 10, channel 1, CSP PDO layout |
|
||||
| Unused drive channel | EL7062 channel 2, `Generic-Ch-Not-Used` |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum, 0.5 A standby, 48 V nominal, 7.5 ohm/phase, 3080 uH, 400 full steps/revolution |
|
||||
| Outer-loop feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Limit-switch supply | EL2008 slave 5, channel 4 switched output |
|
||||
| Position unit | mm |
|
||||
|
||||
## Encoder and drive scaling
|
||||
|
||||
All position signals in the two loops must use the same engineering coordinate
|
||||
system.
|
||||
|
||||
### Primary SSI encoder: ECMC outer loop
|
||||
|
||||
- SSI, 24-bit binary, 1 MHz clock
|
||||
- EL5042 supply configured to 9.0 V
|
||||
- Scale: `1 / 10000 mm/count`, or `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Absolute encoder with wraparound disabled
|
||||
- Ready bit 2, warning bit 0, error bit 1
|
||||
|
||||
### EL7062 CSP drive encoder: inner loop
|
||||
|
||||
- Scale: `1 / 1048576 mm/count` for a 1 mm/revolution stage
|
||||
- Incremental, 32-bit position counter
|
||||
- Referenced to primary SSI encoder index 0 at startup
|
||||
- Selected with `useAsCSPDrvEnc: 1`
|
||||
|
||||
### CSP position command
|
||||
|
||||
- Scale: `1 / 1048576 mm/count`
|
||||
- Setpoint PDO: `positionSetpoint01`
|
||||
- Control/status PDOs: `driveControl01` and `driveStatus01`
|
||||
- DS402/advanced drive type: `1`
|
||||
|
||||
## Outer ECMC controller
|
||||
|
||||
The current outer-loop controller values are:
|
||||
|
||||
| Parameter | Value |
|
||||
| --- | ---: |
|
||||
| `Kp` | 0.02 |
|
||||
| `Ki` | 0.01 |
|
||||
| `Kd` | 0.01 |
|
||||
| `Kff` | 1 |
|
||||
|
||||
PSI guidance states that CSP-PC normally needs both proportional and integral
|
||||
action because ECMC and the drive each run a position loop. These copied values
|
||||
are not proof of stable tuning. Tune the EL7062 inner loops first, then tune the
|
||||
ECMC outer loop at reduced speed and current while observing both encoder errors.
|
||||
|
||||
## Motion and monitoring
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Default velocity | 2 mm/s |
|
||||
| Default acceleration/deceleration | 2 mm/s^2 |
|
||||
| Emergency deceleration | 10 mm/s^2 |
|
||||
| S-curve jerk | 10 mm/s^3 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 3 mm/s |
|
||||
| Following-error tolerance | 0.05 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.0015 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 10 s |
|
||||
| Automatic disable delay | 10 s idle |
|
||||
|
||||
The hardware limits use EL7062 channel 1 inputs:
|
||||
|
||||
- Backward limit: `binaryInputs01.0`
|
||||
- Forward limit: `binaryInputs01.1`
|
||||
- Limit-switch power: EL2008 channel 4
|
||||
|
||||
Home and external interlock are constant true because no corresponding sensors
|
||||
are assigned. Software limits and axis monitoring remain enabled.
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code_2.plc` with a 500 ms PLC sample period. The active
|
||||
sequence is unchanged from the CSP source configuration:
|
||||
|
||||
- Velocity: 2 mm/s
|
||||
- Acceleration/deceleration: 3 mm/s^2
|
||||
- Ten measurement positions from 1.0000 mm to 90.0000 mm
|
||||
- A preliminary point 0.2 mm below each measurement position
|
||||
- Intermediate dwell: 2 scans, nominally 1 s
|
||||
- Measurement dwell: 12 scans, nominally 6 s
|
||||
- Five forward/backward cycles
|
||||
|
||||
```sh
|
||||
# Start
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
|
||||
# Stop
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Remaining commissioning issues
|
||||
|
||||
- The motor component declares `R_COIL_MOHM=7500`, while the drive-controller
|
||||
component declares `R_COIL_MOHM=2471`. Resolve this mismatch and use EL7062
|
||||
autotune results for the installed motor before enabling motion.
|
||||
- Confirm the EL5042 output is 9.0 V and compatible with the exact encoder order
|
||||
code before connecting the encoder.
|
||||
- Confirm both position signals use the same direction, datum, and scale before
|
||||
closing the outer loop. A sign error in a closed position loop can cause
|
||||
immediate uncontrolled motion.
|
||||
- The PLC accepts busy-low plus `attarget` as move completion without first
|
||||
latching that busy became high. Validate or correct this handshake before
|
||||
unattended operation.
|
||||
- This is a static source configuration. PDO compatibility, loop stability,
|
||||
limit polarity, and safe operation require validation on the target IOC and
|
||||
hardware.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EL5042 SDOs, EL7062 CSP hardware description, motor and drive
|
||||
parameters, axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - primary SSI encoder, CSP position mapping, outer controller,
|
||||
trajectory, limits, and monitoring
|
||||
- `cfg/enc_open_loop.yaml` - EL7062 drive encoder and CSP-PC selection
|
||||
- `cfg/code_2.plc` - active FAT motion sequence
|
||||
- `cfg/code.plc` - alternate older sequence, not loaded by `startup.cmd`
|
||||
|
||||
## Commissioning sequence
|
||||
|
||||
1. Confirm that the IOC is loading `ECMC/EL7062_CSP_PC/startup.cmd`.
|
||||
2. Verify motor phase wiring, configured current, resistance, and inductance.
|
||||
3. Run EL7062 autotune and validate the drive's inner position loop first.
|
||||
4. Confirm 9.0 V at the EL5042 connector before attaching the encoder.
|
||||
5. With the outer loop disabled, compare SSI and EL7062 position direction and
|
||||
scale through a small manually controlled displacement.
|
||||
6. Align/reference the EL7062 counter to the SSI coordinate and verify that no
|
||||
position step occurs during enable.
|
||||
7. Enable the ECMC outer loop with conservative gains, reduced current, and a
|
||||
low following-error threshold appropriate for the test.
|
||||
8. Tune `Kp` and `Ki`, adding derivative action only if measurements show it is
|
||||
needed. Verify stability at standstill, during motion, and after reversal.
|
||||
9. Exercise both hardware limits and software limits at low velocity.
|
||||
10. Validate the PLC execute/busy handshake before running the complete FAT
|
||||
sequence.
|
||||
@@ -0,0 +1,105 @@
|
||||
axis: # Physical-axis configuration
|
||||
id: ${AXIS_ID=1} # Unique numeric axis identifier
|
||||
feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=04} # EL2008 channel 4: 24 V supply for limit switches
|
||||
type: joint # Physical motor axis
|
||||
mode: CSP # CSP-PC uses CSP plus a designated CSP drive encoder
|
||||
autoEnable: # Native ecmc automatic axis enable/disable
|
||||
enableTimeout: 10 # Maximum time allowed to auto-enable [s]
|
||||
disableTimeout: 10 # Idle time before automatic disable [s]
|
||||
tweakDist: 1.0
|
||||
|
||||
plc: # Axis PLC configuration
|
||||
id: 1 # PLC identifier
|
||||
enable: yes # Enable the axis PLC
|
||||
externalCommands: true # Allow the PLC to issue axis commands
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1}
|
||||
precision: 3
|
||||
description: OWIS Stage EL7062 CSP-PC
|
||||
unit: mm
|
||||
motorRecord:
|
||||
syncSoftLimits: False
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen'
|
||||
|
||||
|
||||
drive:
|
||||
numerator: 1 # Stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 # EL7062 CSP position units per revolution
|
||||
type: 1 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).positionSetpoint01 # CSP position setpoint to the EL7062
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word EtherCAT entry
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word EtherCAT entry
|
||||
warning: 2 # Warning bit in status word (if no drive warning bit then leave empty)
|
||||
error: # max 3 error bits in status word
|
||||
- 3 # Error 0 (if no drive error bit then leave empty)
|
||||
- 7 # Error 1 (if no drive error bit then leave empty)
|
||||
- 14 # Error 2 (if no drive error bit then leave empty)
|
||||
|
||||
encoder: # Primary encoder configuration
|
||||
primary: true # Use this encoder as the primary feedback encoder
|
||||
desc: SSI # Encoder description: TR-Electronic LT140-S SSI
|
||||
numerator: 1 # Encoder scaling numerator [mm]
|
||||
denominator: 10000 # Interferometer-calibrated encoder scale [counts/mm]
|
||||
type: 1 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 24 # Total raw encoder data width [bits]
|
||||
absBits: 24 # Absolute-data width in the least-significant part of the raw value [bits]
|
||||
absOffset: -11.826 # Absolute encoder offset in engineering units [mm]
|
||||
allowOverUnderFlow: false # Disallow raw-counter wraparound for this linear encoder
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # EtherCAT encoder actual-position entry
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # EtherCAT encoder status-word entry; required by warning/error checks
|
||||
ready: 2 # Ready-bit index in the encoder status word
|
||||
warning: 0 # Warning-bit index in the encoder status word
|
||||
error: # Encoder-error bit indices in the status word; maximum three
|
||||
- 1 # Encoder error 0 bit
|
||||
delayComp: # Compensation for delay between setpoint output and encoder readback
|
||||
time: 0 # Compensation delay [EtherCAT cycles]
|
||||
enable: true # Enable encoder delay compensation
|
||||
|
||||
controller: # Centralized ecmc PID controller for CSP-PC operation
|
||||
Kp: 0.02 # Proportional gain
|
||||
Ki: 0.01 # Integral gain
|
||||
Kd: 0.01 # Derivative gain
|
||||
Kff: 1
|
||||
|
||||
trajectory: # Trajectory-generator configuration
|
||||
type: 1 # Velocity profile: 0=trapezoidal; 1=S-curve (Ruckig)
|
||||
source: 0 # Position source: 0=axis trajectory generator; 1=PLC
|
||||
axis: # Normal-motion initialization values
|
||||
velocity: 2 # Default axis velocity [mm/s]
|
||||
acceleration: 2 # Default axis acceleration [mm/s^2]
|
||||
deceleration: 2 # Default axis deceleration [mm/s^2]
|
||||
emergencyDeceleration: 10 # Emergency deceleration [mm/s^2]
|
||||
jerk: 10 # S-curve jerk [mm/s^3]
|
||||
jog: # Jog-motion initialization values
|
||||
velocity: 1 # Default jog velocity [mm/s]
|
||||
|
||||
input: # Limit, home, and external-interlock inputs
|
||||
limit: # Hardware limit-switch inputs
|
||||
forward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.1 # EtherCAT forward-limit input
|
||||
backward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.0 # EtherCAT backward-limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Home input; constant true because no home sensor is used
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # External interlock; constant true because none is used
|
||||
|
||||
softlimits: # ecmc software travel-limit configuration
|
||||
enable: true # Globally enable software limits
|
||||
forward: 95 # Forward software-limit position [mm]
|
||||
forwardEnable: true # Enable the forward software limit
|
||||
backward: -1 # Backward software-limit position [mm]
|
||||
backwardEnable: true # Enable the backward software limit
|
||||
|
||||
monitoring: # Axis following-error, velocity, and in-position monitoring
|
||||
lag: # Position-lag/following-error monitoring
|
||||
enable: true # Enable position-lag monitoring
|
||||
tolerance: 0.05 # Maximum permitted position lag [mm]
|
||||
time: 10 # Allowed time outside lag tolerance [EtherCAT cycles]
|
||||
velocity: # Axis velocity monitoring
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 3 # Maximum permitted velocity [mm/s]
|
||||
time: # Allowed velocity-violation durations
|
||||
trajectory: 100 # Cycles before trajectory initialization is halted
|
||||
drive: 400 # Cycles before the drive is disabled
|
||||
target: # At-target/in-position monitoring
|
||||
enable: true # Enable at-target monitoring; required by the motor record
|
||||
tolerance: 0.0015 # At-target position tolerance [mm]
|
||||
time: 50 # Required time inside tolerance [EtherCAT cycles]
|
||||
@@ -0,0 +1,159 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,204 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# For every posIndex, in forward and backward travel:
|
||||
# 1. Move to intermediatePos.
|
||||
# 2. Move to pos and measure/dwell only at pos.
|
||||
# intermediatePos is always smaller than pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=0.8000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=10.6900;pos:=10.8900;}
|
||||
if(posIndex==2){intermediatePos:=20.5775;pos:=20.7775;}
|
||||
if(posIndex==3){intermediatePos:=30.4675;pos:=30.6675;}
|
||||
if(posIndex==4){intermediatePos:=40.3550;pos:=40.5550;}
|
||||
if(posIndex==5){intermediatePos:=50.2450;pos:=50.4450;}
|
||||
if(posIndex==6){intermediatePos:=60.1325;pos:=60.3325;}
|
||||
if(posIndex==7){intermediatePos:=70.0225;pos:=70.2225;}
|
||||
if(posIndex==8){intermediatePos:=79.9100;pos:=80.1100;}
|
||||
if(posIndex==9){intermediatePos:=89.8000;pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
|
||||
@@ -0,0 +1,20 @@
|
||||
encoder: # EL7062 open-loop encoder configuration
|
||||
desc: 'CSP drive encoder' # EL7062 internal position used by the drive loop
|
||||
primary: false # Do not use this encoder as primary position feedback
|
||||
unit: mm # Encoder engineering unit
|
||||
numerator: 1 # Encoder scaling numerator: stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 # Encoder scaling denominator: EL7062 CSP units per revolution
|
||||
type: 0 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 32 # Total raw encoder counter width [bits]
|
||||
absBits: 0 # Absolute-data width [bits]; zero for an incremental encoder
|
||||
absOffset: 0 # Absolute encoder offset in engineering units [mm]
|
||||
position: ec0.s$(DRV_SID).positionActual01 # EtherCAT EL7062 open-loop actual-position entry
|
||||
homing: # Referencing configuration for this incremental encoder
|
||||
refToEncIDAtStartup: 0 # At startup, reference to primary SSI encoder index 0
|
||||
type: 2 # Homing/reference sequence type
|
||||
position: 0 # Reference position in engineering units [mm]
|
||||
velocity: # Homing velocities
|
||||
to: 0.5 # Velocity toward the reference cam/sensor [mm/s]
|
||||
from: 0.25 # Velocity away from the reference cam/sensor [mm/s]
|
||||
useAsCSPDrvEnc: 1 # Enables the ECMC outer position loop: CSP-PC
|
||||
|
||||
@@ -0,0 +1,65 @@
|
||||
# Script used to control the FAT stage in EL7062 CSP-PC dual-position-loop mode
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,true) # Override reset of EL5042
|
||||
|
||||
# EL2008 channel 4 supplies 24 V to the EL7062 limit switches
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=5,HW_DESC=EL2008"
|
||||
epicsEnvSet(BO_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
# EL7062 channel 1 in CSP with centralized ECMC position control (CSP-PC)
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=10,HW_DESC=EL7062_CSP"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=1,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=1,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=2,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=2,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#- Channel 2 is unused and must be acknowledged for SDO-settings verification
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2"
|
||||
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml,DEV=${IOC},AX_NAME=M1,AXIS_ID=1,DRV_SID=${DRV_SID},ENC_SID=${ENC_SID},ENC_CH=01,BO_SID=${BO_SID}"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml,DEV=${IOC},ENC_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/code_2.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
|
||||
# Start motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
# Stop motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
@@ -0,0 +1,218 @@
|
||||
# OWIS stage with EL7062 CSV and TR SSI encoder
|
||||
|
||||
This folder configures the OWIS linear stage with an EL7062 stepper terminal in
|
||||
cyclic synchronous velocity (CSV) mode. Position control is closed through the
|
||||
TR-Electronic LT140-S absolute SSI encoder. The engineering unit is millimetres.
|
||||
|
||||
## Important EL7062 CSV firmware warning
|
||||
|
||||
PSI documents an EL7062 firmware defect in CSV mode: when the drive is disabled,
|
||||
its internal open-loop counter can jump to the nearest full turn (multiples of
|
||||
`1048576` counts). The current PSI best-practice configuration for an EL7062
|
||||
with external position feedback therefore uses CSP instead of CSV.
|
||||
|
||||
Use `../EL7062_CSP` for normal operation unless the installed EL7062 firmware is
|
||||
positively identified as containing the vendor fix. Before commissioning this
|
||||
CSV variant, reproduce the enable/move/disable test at low speed and confirm
|
||||
that `positionActual01` remains continuous across disable and re-enable.
|
||||
|
||||
References reviewed at PSI `ecmccfg` commit
|
||||
[`b30e4607`](https://github.com/paulscherrerinstitute/ecmccfg/commit/b30e46072f900b37f7c674aee9a77b3c18f27735):
|
||||
|
||||
- [EL7062/EL5042 best-practice configuration](https://github.com/paulscherrerinstitute/ecmccfg/blob/b30e46072f900b37f7c674aee9a77b3c18f27735/examples/PSI/best_practice/motion/stepper_bissc/el7062_el5042/README.md)
|
||||
- [EL7062 CSV firmware-warning example](https://github.com/paulscherrerinstitute/ecmccfg/blob/b30e46072f900b37f7c674aee9a77b3c18f27735/examples/PSI/lab_setup/el7062/openloop/README.md)
|
||||
- [EL7062 closed-loop CSV lab example](https://github.com/paulscherrerinstitute/ecmccfg/tree/b30e46072f900b37f7c674aee9a77b3c18f27735/examples/PSI/lab_setup/el7062/closed_loop_bissc)
|
||||
- [EtherCAT-rate guidance](https://paulscherrerinstitute.github.io/ecmccfg/manual/general_cfg/best_practice/)
|
||||
|
||||
## CSV configuration changes
|
||||
|
||||
The CSV folder now differs from `../EL7062_CSP` in all mode-dependent settings:
|
||||
|
||||
| Setting | CSV value | Reason |
|
||||
| --- | --- | --- |
|
||||
| Hardware description | `HW_DESC=EL7062` | Loads the EL7062 CSV PDO layout |
|
||||
| Axis mode | `mode: CSV` | Selects cyclic synchronous velocity operation |
|
||||
| Drive setpoint | `velocitySetpoint01` | CSV commands velocity, not position |
|
||||
| Drive numerator | `500` | `1 mm/revolution * 500 EtherCAT cycles/second` |
|
||||
| Drive denominator | `2147483648` | Signed 32-bit CSV velocity range |
|
||||
| CSP drive encoder flag | Omitted | `useAsCSPDrvEnc` applies only to CSP |
|
||||
| Channel 2 | `Generic-Ch-Not-Used` | Completes SDO handling without configuring an absent motor |
|
||||
|
||||
The CSV drive conversion is therefore:
|
||||
|
||||
```text
|
||||
raw velocity = commanded velocity * 2147483648 / 500
|
||||
commanded velocity = raw velocity * 500 / 2147483648 mm/s
|
||||
```
|
||||
|
||||
At the configured 2 mm/s motion velocity, the nominal raw velocity command is
|
||||
approximately `8589935` counts. This calculation must be checked against the
|
||||
live command and actual-velocity entries during low-speed commissioning.
|
||||
|
||||
## System configuration
|
||||
|
||||
| Function | Configured hardware or setting |
|
||||
| --- | --- |
|
||||
| ECMC | `ecmccfg 11.0.8`, engineering mode enabled, `EC_RATE=500` Hz |
|
||||
| Motion axis | Axis 1, EPICS name `M1`, description `OWIS Stage EL7062` |
|
||||
| Stepper terminal | EL7062 at EtherCAT slave 10, channel 1, CSV mode |
|
||||
| Unused drive channel | EL7062 channel 2, `Generic-Ch-Not-Used` |
|
||||
| Motor | OWIS two-phase stepper; 0.8 A maximum, 0.5 A standby, 48 V nominal, 7.5 ohm/phase, 3080 uH, 400 full steps/revolution |
|
||||
| Primary feedback | TR-Electronic LT140-S on EL5042 slave 2, channel 1 |
|
||||
| Limit-switch supply | EL2008 slave 5, channel 4 switched output |
|
||||
| Position unit | mm |
|
||||
|
||||
`EC_RATE=500` is a 500 Hz EtherCAT rate. PSI describes 100-500 Hz as a normal
|
||||
range for many motion systems.
|
||||
|
||||
## Encoder configuration
|
||||
|
||||
### Primary SSI encoder
|
||||
|
||||
The EL5042 channel is configured by SDO before the axis is loaded:
|
||||
|
||||
- SSI mode, binary coding
|
||||
- 24 position bits, no multiturn or offset bits
|
||||
- Status bits disabled and CRC inversion enabled
|
||||
- 1 MHz clock
|
||||
- 9.0 V encoder supply
|
||||
- Scale: `1 / 10000 mm/count`, equivalent to `0.1 um/count`
|
||||
- Absolute offset: `-11.826 mm`
|
||||
- Counter overflow/wraparound disabled
|
||||
|
||||
The `10000 counts/mm` value is labelled as interferometer-calibrated in
|
||||
`cfg/axis.yaml`. The files do not establish its calibration uncertainty or
|
||||
confirm the current mechanical datum.
|
||||
|
||||
### EL7062 open-loop counter
|
||||
|
||||
- Secondary encoder; the SSI encoder remains primary feedback
|
||||
- Scale: `1 / 1048576 mm/count` for a 1 mm/revolution stage
|
||||
- Incremental, 32-bit counter
|
||||
- Referenced to the primary SSI encoder at startup (`refToEncIDAtStartup: 0`)
|
||||
- Not selected as a CSP drive encoder
|
||||
|
||||
The counter is retained for observation and comparison. It is also the signal
|
||||
affected by the documented CSV disable defect.
|
||||
|
||||
## Axis behaviour
|
||||
|
||||
| Characteristic | Configured value |
|
||||
| --- | --- |
|
||||
| Default velocity | 2 mm/s |
|
||||
| Default acceleration/deceleration | 2 mm/s^2 |
|
||||
| Emergency deceleration | 10 mm/s^2 |
|
||||
| S-curve jerk | 10 mm/s^3 |
|
||||
| Jog velocity | 1 mm/s |
|
||||
| Backward software limit | -1 mm |
|
||||
| Forward software limit | 95 mm |
|
||||
| Maximum monitored velocity | 3 mm/s |
|
||||
| Following-error tolerance | 0.05 mm for 10 EtherCAT cycles |
|
||||
| At-target tolerance | 0.0015 mm for 50 EtherCAT cycles |
|
||||
| Auto-enable timeout | 10 s |
|
||||
| Automatic disable delay | 10 s idle |
|
||||
|
||||
The centralized ECMC controller closes the position loop using the SSI encoder
|
||||
and produces the EL7062 CSV velocity command. The configured gains are:
|
||||
|
||||
| Parameter | Value |
|
||||
| --- | ---: |
|
||||
| `Kp` | 0.02 |
|
||||
| `Ki` | 0.01 |
|
||||
| `Kd` | 0.01 |
|
||||
| `Kff` | 1 |
|
||||
|
||||
PSI notes that CSV normally needs proportional gain at minimum. These local
|
||||
values are retained from the source configuration and must be tuned and verified
|
||||
with the installed mechanics.
|
||||
|
||||
The hardware limits use EL7062 channel 1 inputs:
|
||||
|
||||
- Backward limit: `binaryInputs01.0`
|
||||
- Forward limit: `binaryInputs01.1`
|
||||
- Limit-switch power: EL2008 channel 4
|
||||
|
||||
Home and external interlock are constant true because no corresponding sensors
|
||||
are assigned. Software limits and axis monitoring remain enabled.
|
||||
|
||||
## Automatic FAT motion sequence
|
||||
|
||||
`startup.cmd` loads `cfg/code_2.plc` at a 500 ms PLC sample period. A rising edge
|
||||
on `doMotion` starts the sequence.
|
||||
|
||||
- Move velocity: 2 mm/s
|
||||
- Acceleration and deceleration: 3 mm/s^2
|
||||
- Ten measurement positions from 1.0000 mm to 90.0000 mm
|
||||
- A preliminary position 0.2 mm below each measurement point, giving a final
|
||||
positive-direction approach
|
||||
- Intermediate dwell: 2 PLC scans, nominally 1 s
|
||||
- Measurement dwell: 12 PLC scans, nominally 6 s
|
||||
- Five forward/backward cycles
|
||||
|
||||
The ten `(preliminary -> measurement)` pairs are:
|
||||
|
||||
```text
|
||||
0.8000 -> 1.0000 mm
|
||||
10.6900 -> 10.8900 mm
|
||||
20.5775 -> 20.7775 mm
|
||||
30.4675 -> 30.6675 mm
|
||||
40.3550 -> 40.5550 mm
|
||||
50.2450 -> 50.4450 mm
|
||||
60.1325 -> 60.3325 mm
|
||||
70.0225 -> 70.2225 mm
|
||||
79.9100 -> 80.1100 mm
|
||||
89.8000 -> 90.0000 mm
|
||||
```
|
||||
|
||||
The PLC powers off the axis and disables itself if either limit becomes invalid
|
||||
or `mc_move_abs()` returns an error.
|
||||
|
||||
```sh
|
||||
# Start
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
|
||||
# Stop
|
||||
caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
```
|
||||
|
||||
## Remaining commissioning issues
|
||||
|
||||
- The motor component declares `R_COIL_MOHM=7500`, while the controller
|
||||
component declares `R_COIL_MOHM=2471`. Resolve this mismatch before enabling
|
||||
the drive. Motor resistance, inductance, and controller parameters should be
|
||||
obtained from the installed motor and EL7062 autotune.
|
||||
- The PLC currently accepts busy-low plus `attarget` as move completion without
|
||||
first latching that busy became high. Validate the helper behaviour or add the
|
||||
established execute/busy handshake before unattended operation.
|
||||
- The configured 9.0 V EL5042 supply must be checked physically and confirmed
|
||||
against the exact encoder order code before connecting the encoder.
|
||||
- Static source consistency does not prove PDO compatibility, correct polarity,
|
||||
stable control, or safe motion on the installed hardware.
|
||||
|
||||
## Relevant files
|
||||
|
||||
- `startup.cmd` - EtherCAT slaves, SSI SDOs, CSV hardware description, motor and
|
||||
controller components, axis loading, and PLC loading
|
||||
- `cfg/axis.yaml` - CSV drive mapping, primary SSI feedback, trajectory, limits,
|
||||
controller, and monitoring
|
||||
- `cfg/enc_open_loop.yaml` - secondary EL7062 open-loop counter
|
||||
- `cfg/code_2.plc` - active multi-position FAT sequence
|
||||
- `cfg/code.plc` - alternate older sequence, not loaded by `startup.cmd`
|
||||
|
||||
## Commissioning sequence
|
||||
|
||||
1. Confirm that the IOC is loading `ECMC/EL7062_CSV/startup.cmd`.
|
||||
2. Verify the installed EL7062 firmware and resolve the CSV counter-defect gate.
|
||||
3. Confirm channel 1 motor wiring and that channel 2 is physically unused.
|
||||
4. Resolve the 7500/2471 mOhm resistance mismatch, run autotune, and apply the
|
||||
resulting motor/controller parameters.
|
||||
5. Confirm 9.0 V at the EL5042 connector before attaching the encoder.
|
||||
6. With motion disabled, verify SSI readiness, raw position, status bits, limit
|
||||
inputs, and limit-switch supply.
|
||||
7. Enable at reduced current and command a very low positive velocity. Confirm
|
||||
motor direction, SSI direction, `velocitySetpoint01`, and actual velocity.
|
||||
8. Move within one motor revolution, disable, and verify that
|
||||
`positionActual01` does not jump to a multiple of `1048576` counts.
|
||||
9. Verify following error, settling, software limits, and stop behaviour.
|
||||
10. Validate the PLC execute/busy handshake before running the complete FAT
|
||||
sequence.
|
||||
@@ -0,0 +1,105 @@
|
||||
axis: # Physical-axis configuration
|
||||
id: ${AXIS_ID=1} # Unique numeric axis identifier
|
||||
feedSwitchesOutput: ec0.s${BO_SID}.binaryOutput${BO_CH=04} # EL2008 channel 4: 24 V supply for limit switches
|
||||
type: joint # Physical motor axis
|
||||
mode: CSV # EL7062 cyclic synchronous velocity mode
|
||||
autoEnable: # Native ecmc automatic axis enable/disable
|
||||
enableTimeout: 10 # Maximum time allowed to auto-enable [s]
|
||||
disableTimeout: 10 # Idle time before automatic disable [s]
|
||||
tweakDist: 1.0
|
||||
|
||||
plc: # Axis PLC configuration
|
||||
id: 1 # PLC identifier
|
||||
enable: yes # Enable the axis PLC
|
||||
externalCommands: true # Allow the PLC to issue axis commands
|
||||
|
||||
epics:
|
||||
name: ${AX_NAME=M1}
|
||||
precision: 3
|
||||
description: OWIS Stage EL7062
|
||||
unit: mm
|
||||
motorRecord:
|
||||
syncSoftLimits: False
|
||||
fieldInit: 'RTRY=0,FOFF=Frozen'
|
||||
|
||||
|
||||
drive:
|
||||
numerator: 1 # 1 mm/rev * 500 EtherCAT cycles/s
|
||||
denominator: 1048576 #10737418 #2147483648 # Signed 32-bit EL7062 CSV velocity range
|
||||
type: 1 # Stepper: 0. DS402: 1 (DS402 = servos and advanced stepper drives)
|
||||
setpoint: ec0.s$(DRV_SID).velocitySetpoint01 # EL7062 CSV velocity setpoint
|
||||
control: ec0.s$(DRV_SID).driveControl01 # Control word EtherCAT entry
|
||||
status: ec0.s$(DRV_SID).driveStatus01 # Status word EtherCAT entry
|
||||
warning: 2 # Warning bit in status word (if no drive warning bit then leave empty)
|
||||
error: # max 3 error bits in status word
|
||||
- 3 # Error 0 (if no drive error bit then leave empty)
|
||||
- 7 # Error 1 (if no drive error bit then leave empty)
|
||||
- 14 # Error 2 (if no drive error bit then leave empty)
|
||||
|
||||
encoder: # Primary encoder configuration
|
||||
primary: true # Use this encoder as the primary feedback encoder
|
||||
desc: SSI # Encoder description: TR-Electronic LT140-S SSI
|
||||
numerator: 1 # Encoder scaling numerator [mm]
|
||||
denominator: 10000 # Interferometer-calibrated encoder scale [counts/mm]
|
||||
type: 1 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 24 # Total raw encoder data width [bits]
|
||||
absBits: 24 # Absolute-data width in the least-significant part of the raw value [bits]
|
||||
absOffset: -11.826 # Absolute encoder offset in engineering units [mm]
|
||||
allowOverUnderFlow: false # Disallow raw-counter wraparound for this linear encoder
|
||||
position: ec0.s$(ENC_SID).positionActual${ENC_CH=01} # EtherCAT encoder actual-position entry
|
||||
status: ec0.s$(ENC_SID).encoderStatus${ENC_CH=01} # EtherCAT encoder status-word entry; required by warning/error checks
|
||||
ready: 2 # Ready-bit index in the encoder status word
|
||||
warning: 0 # Warning-bit index in the encoder status word
|
||||
error: # Encoder-error bit indices in the status word; maximum three
|
||||
- 1 # Encoder error 0 bit
|
||||
delayComp: # Compensation for delay between setpoint output and encoder readback
|
||||
time: 0 # Compensation delay [EtherCAT cycles]
|
||||
enable: true # Enable encoder delay compensation
|
||||
|
||||
controller: # Centralized ecmc position controller driving CSV velocity
|
||||
Kp: 14 # Proportional gain
|
||||
Ki: 1.6 # Integral gain
|
||||
Kd: 0.5 # Derivative gain
|
||||
Kff: 1
|
||||
|
||||
trajectory: # Trajectory-generator configuration
|
||||
type: 0 # Velocity profile: 0=trapezoidal; 1=S-curve (Ruckig)
|
||||
source: 0 # Position source: 0=axis trajectory generator; 1=PLC
|
||||
axis: # Normal-motion initialization values
|
||||
velocity: 3 # Default axis velocity [mm/s]
|
||||
acceleration: 2 # Default axis acceleration [mm/s^2]
|
||||
deceleration: 2 # Default axis deceleration [mm/s^2]
|
||||
emergencyDeceleration: 10 # Emergency deceleration [mm/s^2]
|
||||
jerk: 10 # S-curve jerk [mm/s^3]
|
||||
jog: # Jog-motion initialization values
|
||||
velocity: 1 # Default jog velocity [mm/s]
|
||||
|
||||
input: # Limit, home, and external-interlock inputs
|
||||
limit: # Hardware limit-switch inputs
|
||||
forward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.1 # EtherCAT forward-limit input
|
||||
backward: ec0.s$(DRV_SID).binaryInputs${DRV_CH=01}.0 # EtherCAT backward-limit input
|
||||
home: 'ec0.s$(DRV_SID).ONE.0' # Home input; constant true because no home sensor is used
|
||||
interlock: 'ec0.s$(DRV_SID).ONE.0' # External interlock; constant true because none is used
|
||||
|
||||
softlimits: # ecmc software travel-limit configuration
|
||||
enable: true # Globally enable software limits
|
||||
forward: 95 # Forward software-limit position [mm]
|
||||
forwardEnable: true # Enable the forward software limit
|
||||
backward: -1 # Backward software-limit position [mm]
|
||||
backwardEnable: true # Enable the backward software limit
|
||||
|
||||
monitoring: # Axis following-error, velocity, and in-position monitoring
|
||||
lag: # Position-lag/following-error monitoring
|
||||
enable: true # Enable position-lag monitoring
|
||||
tolerance: 0.5 # Maximum permitted position lag [mm]
|
||||
time: 10 # Allowed time outside lag tolerance [EtherCAT cycles]
|
||||
velocity: # Axis velocity monitoring
|
||||
enable: true # Enable velocity monitoring
|
||||
max: 10 # Maximum permitted velocity [mm/s]
|
||||
time: # Allowed velocity-violation durations
|
||||
trajectory: 100 # Cycles before trajectory initialization is halted
|
||||
drive: 400 # Cycles before the drive is disabled
|
||||
target: # At-target/in-position monitoring
|
||||
enable: true # Enable at-target monitoring; required by the motor record
|
||||
tolerance: 0.002 # At-target position tolerance [mm]
|
||||
time: 50 # Required time inside tolerance [EtherCAT cycles]
|
||||
@@ -0,0 +1,158 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of scan positions, count with the 0 position :)
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){pos:=1.0000;}
|
||||
if(posIndex==1){pos:=10.8575;}
|
||||
if(posIndex==2){pos:=20.1050;}
|
||||
if(posIndex==3){pos:=31.8050;}
|
||||
if(posIndex==4){pos:=38.3275;}
|
||||
if(posIndex==5){pos:=51.9900;}
|
||||
if(posIndex==6){pos:=57.6875;}
|
||||
if(posIndex==7){pos:=71.4650;}
|
||||
if(posIndex==8){pos:=81.2450;}
|
||||
if(posIndex==9){pos:=90.0000;}
|
||||
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 – move to next position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
|
||||
println('Move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 – dwell
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
@@ -0,0 +1,203 @@
|
||||
#############
|
||||
# PLC multi-position motion sequence
|
||||
#
|
||||
# Motion parameters
|
||||
#
|
||||
|
||||
var VEL := 2;
|
||||
var ACC := 3;
|
||||
var DEC := 3;
|
||||
|
||||
var INTERMEDIATE_DWELL_TIME := 2;
|
||||
var DWELL_TIME := 12;
|
||||
var N_POS := 10; # number of calibrated measurement positions
|
||||
var MAX_CYCLES := 5;
|
||||
|
||||
VAR
|
||||
myAxis : ax${AX_ID=1};
|
||||
step : static.seqStep;
|
||||
cycles : static.cycleCounter;
|
||||
doMotion : static.doMotion;
|
||||
doMotionOld : static.doMotionOld;
|
||||
posIndex : static.posIndex;
|
||||
direction : static.direction;
|
||||
dwellCnt : static.dwellCnt;
|
||||
END_VAR
|
||||
|
||||
|
||||
var errorCode := 0;
|
||||
var intermediatePos := 0;
|
||||
var pos := 0;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Initialization
|
||||
# --------------------------------------------------
|
||||
|
||||
if(${SELF}.firstscan){
|
||||
step := 0;
|
||||
cycles := 0;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
dwellCnt := 0;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Trigger start
|
||||
# --------------------------------------------------
|
||||
|
||||
if(doMotion and not(doMotionOld)){
|
||||
println('PLC position sequence started');
|
||||
step := 1;
|
||||
posIndex := 0;
|
||||
direction := 1;
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Position lookup
|
||||
# --------------------------------------------------
|
||||
|
||||
# For every posIndex, in forward and backward travel:
|
||||
# 1. Move to intermediatePos.
|
||||
# 2. Move to pos and measure/dwell only at pos.
|
||||
# intermediatePos is always smaller than pos.
|
||||
|
||||
intermediatePos := 0;
|
||||
pos := 0;
|
||||
|
||||
if(posIndex==0){intermediatePos:=0.8000;pos:=1.0000;}
|
||||
if(posIndex==1){intermediatePos:=10.6900;pos:=10.8900;}
|
||||
if(posIndex==2){intermediatePos:=20.5775;pos:=20.7775;}
|
||||
if(posIndex==3){intermediatePos:=30.4675;pos:=30.6675;}
|
||||
if(posIndex==4){intermediatePos:=40.3550;pos:=40.5550;}
|
||||
if(posIndex==5){intermediatePos:=50.2450;pos:=50.4450;}
|
||||
if(posIndex==6){intermediatePos:=60.1325;pos:=60.3325;}
|
||||
if(posIndex==7){intermediatePos:=70.0225;pos:=70.2225;}
|
||||
if(posIndex==8){intermediatePos:=79.9100;pos:=80.1100;}
|
||||
if(posIndex==9){intermediatePos:=89.8000;pos:=90.0000;}
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 1 - move to intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==1 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,intermediatePos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 2;
|
||||
println('Intermediate move done, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 2 - dwell at intermediate position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==2 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= INTERMEDIATE_DWELL_TIME){
|
||||
step := 3;
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 3 - move to measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==3 and doMotion){
|
||||
|
||||
errorCode := mc_move_abs(${AX_ID=1},1,pos,VEL,ACC,DEC);
|
||||
|
||||
if(errorCode){
|
||||
println('mc_move_abs error:',errorCode);
|
||||
${SELF}.error := errorCode;
|
||||
};
|
||||
|
||||
if(not(mc_get_busy(${AX_ID=1})) and myAxis.mon.attarget){
|
||||
|
||||
mc_move_abs(${AX_ID=1},0,pos,VEL,ACC,DEC);
|
||||
|
||||
dwellCnt := 0;
|
||||
step := 4;
|
||||
|
||||
println('Measurement position reached, index:',posIndex);
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# STEP 4 - dwell at measurement position
|
||||
# --------------------------------------------------
|
||||
|
||||
if(step==4 and doMotion){
|
||||
|
||||
dwellCnt := dwellCnt + 1;
|
||||
|
||||
if(dwellCnt >= DWELL_TIME){
|
||||
|
||||
posIndex := posIndex + direction;
|
||||
|
||||
# reached end of list
|
||||
if(posIndex >= N_POS){
|
||||
direction := -1;
|
||||
posIndex := N_POS - 2;
|
||||
};
|
||||
|
||||
# reached start of list
|
||||
if(posIndex < 0){
|
||||
|
||||
direction := 1;
|
||||
posIndex := 1;
|
||||
|
||||
cycles := cycles + 1;
|
||||
|
||||
println('Cycle completed:',cycles);
|
||||
|
||||
if(cycles >= MAX_CYCLES){
|
||||
println('Sequence completed');
|
||||
doMotion := 0;
|
||||
step := 0;
|
||||
};
|
||||
};
|
||||
|
||||
if(step<>0){
|
||||
step := 1;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
|
||||
doMotionOld := doMotion;
|
||||
|
||||
|
||||
# --------------------------------------------------
|
||||
# Safety
|
||||
# --------------------------------------------------
|
||||
|
||||
if(not(myAxis.drv.enabled)){
|
||||
return [];
|
||||
};
|
||||
|
||||
if(((not(ax1.mon.lowlim) or not(ax1.mon.highlim))) or errorCode){
|
||||
mc_power(${AX_ID=1},0);
|
||||
println('Sequence ended by limit switch violation or errorcode:', errorCode);
|
||||
step := 0;
|
||||
${SELF}.enable := 0;
|
||||
};
|
||||
|
||||
@@ -0,0 +1,19 @@
|
||||
encoder: # EL7062 open-loop encoder configuration
|
||||
desc: 'Open loop' # Encoder description
|
||||
primary: false # Do not use this encoder as primary position feedback
|
||||
unit: mm # Encoder engineering unit
|
||||
numerator: 1 # Encoder scaling numerator: stage travel per motor revolution [mm/rev]
|
||||
denominator: 1048576 # Encoder scaling denominator: EL7062 counts per revolution
|
||||
type: 0 # Encoder type: 0=incremental; 1=absolute
|
||||
bits: 32 # Total raw encoder counter width [bits]
|
||||
absBits: 0 # Absolute-data width [bits]; zero for an incremental encoder
|
||||
absOffset: 0 # Absolute encoder offset in engineering units [mm]
|
||||
position: ec0.s$(DRV_SID).positionActual01 # EtherCAT EL7062 open-loop actual-position entry
|
||||
homing: # Referencing configuration for this incremental encoder
|
||||
refToEncIDAtStartup: 0 # At startup, reference to primary SSI encoder index 0
|
||||
type: 2 # Homing/reference sequence type
|
||||
position: 0 # Reference position in engineering units [mm]
|
||||
velocity: # Homing velocities
|
||||
to: 0.5 # Velocity toward the reference cam/sensor [mm/s]
|
||||
from: 0.25 # Velocity away from the reference cam/sensor [mm/s]
|
||||
|
||||
@@ -0,0 +1,64 @@
|
||||
# Script used to control the FAT stage in closed-loop configuration with EL7062
|
||||
require ecmccfg 11.0.8 "ENG_MODE=1, EC_RATE=500"
|
||||
require ecmccomp
|
||||
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,false) # Override reset of EL5042
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=2,HW_DESC=EL5042_DC"
|
||||
|
||||
#- Shift away the 2 status bits (ST_BITS=26, OFF_BITS=2, total 28bits)
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Encoder-Generic-SSI,CH_ID=1,MACROS=MT_BITS=0,ST_BITS=24,CLK_FRQ_KHZ=1000,CODING=0,OFF_BITS=0"
|
||||
epicsEnvSet(ENC_SID,${ECMC_EC_SLAVE_NUM})
|
||||
# -------------------------------------------------------------------------------------
|
||||
# EL5042 Channel 1
|
||||
# TR-Electronic LT140-S
|
||||
# SSI / 24 bit / Binary / 1 MHz / 9 V
|
||||
# -------------------------------------------------------------------------------------
|
||||
#- To allow change to 9v, 0xF008 must be set to 0x72657375
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0xF008,0x0,0x72657375,4)"
|
||||
|
||||
# Disable status bits = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x02,1,1)"
|
||||
# CRC invert = TRUE
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x03,1,1)"
|
||||
# CRC polynomial = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x11,0,4)"
|
||||
# Supply voltage = 9.0 V
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x12,90,1)"
|
||||
# Clock frequency = 1 MHz
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x13,9,1)"
|
||||
# Coding = Binary / Dual code
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x14,0,1)"
|
||||
# Multiturn bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x15,0,1)"
|
||||
# Singleturn / position bits = 24
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x16,24,1)"
|
||||
# Offset LSB bits = 0
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x17,0,1)"
|
||||
#Mode = SSI
|
||||
ecmcConfigOrDie "Cfg.EcAddSdo(${ECMC_EC_SLAVE_NUM},0x8008,0x18,1,1)"
|
||||
epicsEnvSet(ECMC_SLAVE_RESET,true) # Override reset of EL5042
|
||||
|
||||
# EL2008 channel 4 supplies 24 V to the EL7062 limit switches
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=5,HW_DESC=EL2008"
|
||||
epicsEnvSet(BO_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
# EL7062 two-channel stepper drive in CSV mode (EtherCAT slave position 10)
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=10,HW_DESC=EL7062"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=1,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=1,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Motor-Generic-2Phase-Stepper,CH_ID=2,MACROS='I_MAX_MA=800,I_STDBY_MA=500,U_NOM_MV=48000,L_COIL_UH=3080,R_COIL_MOHM=7500,STEPS=400'"
|
||||
#${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Drive-Generic-Ctrl-Params,CH_ID=2,MACROS='L_COIL_UH=3080,R_COIL_MOHM=2471,I_TI=12,I_KP=58,V_TI=150,V_KP=176,P_KP=10'"
|
||||
#- Must tell ecmc that channel is not used
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}applyComponent.cmd "COMP=Generic-Ch-Not-Used, CH_ID=2"
|
||||
epicsEnvSet(DRV_SID,${ECMC_EC_SLAVE_NUM})
|
||||
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlAxis.cmd, "FILE=./cfg/axis.yaml,DEV=${IOC},AX_NAME=M1,AXIS_ID=1,DRV_SID=${DRV_SID},ENC_SID=${ENC_SID},ENC_CH=01,BO_SID=${BO_SID}"
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadYamlEnc.cmd, "FILE=./cfg/enc_open_loop.yaml,DEV=${IOC},ENC_SID=${DRV_SID}"
|
||||
|
||||
# PLC configuration
|
||||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPLCFile.cmd "FILE=./cfg/code_2.plc,SAMPLE_RATE_MS=500,PLC_MACROS='AX_ID=1'"
|
||||
dbLoadRecords("ecmcPlcAnalog.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.seqStep,REC_NAME=-M${AX_ID=1}-State")
|
||||
dbLoadRecords("ecmcPlcBinary.db","P=$(IOC):,PORT=MC_CPU1,ASYN_NAME=plcs.plc${ECMC_PLC_ID}.static.doMotion,REC_NAME=-M${AX_ID=1}-DoMtn")
|
||||
|
||||
# Start motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 1
|
||||
# Stop motion with: caput aik-motion-pc5:Set-M1-DoMtn-RB 0
|
||||
@@ -0,0 +1,22 @@
|
||||
#Python Environment SLSLC
|
||||
source /psi.ch/group/8315/python/tcr/bin/activate
|
||||
|
||||
------------------------------------
|
||||
#Copy files from ioc to lx-term
|
||||
scp -r garcia_h@slslc:/ioc/hosts/aik-motion-pc5/temp_control /home/garcia_h/Documents
|
||||
|
||||
------------------------------------
|
||||
#Expose PV to terminal
|
||||
export EPICS_CA_ADDR_LIST=129.129.181.171
|
||||
#or
|
||||
export EPICS_CA_ADDR_LIST=aik-motion-pc5
|
||||
|
||||
------------------------------------
|
||||
#Open ECMC/GUI
|
||||
caqtdm -macro IOC=aik-motion-pc5 ecmcMain.ui
|
||||
|
||||
------------------------------------
|
||||
#Run IOC command
|
||||
sudo iocsh -7.0.9 startup.cmd
|
||||
|
||||
------------------------------------
|
||||
|
After Width: | Height: | Size: 3.2 MiB |
@@ -0,0 +1,201 @@
|
||||
<Option Description File - Rev. 1.00a - Keysight E1733A 1.14.1 (Win64)>
|
||||
UserSetup
|
||||
|
||||
Identify=MeaType,Choosing=0
|
||||
Identify=FileName,ItemText=OWIS_stageTR_Electronics_FAT_ISO230_Stepper_ED7062_CSP_EL5042_DC_ClosedLoop_SCurve_gap.Lin
|
||||
Identify=MergedFile,ItemText=
|
||||
Identify=CaliPeriod,"TextUnit=24 Month"
|
||||
Identify=SynchOp,Choosing=1
|
||||
Identify=RotaryDev,Choosing=1
|
||||
Identify=UserEdited,Choosing=0
|
||||
Identify=AutoScale,Choosing=0
|
||||
Identify=StopOnErr,Choosing=1
|
||||
Identify=StopOnLost,Choosing=0
|
||||
Identify=Extended,Choosing=1
|
||||
Identify=TargetSign,Choosing=0
|
||||
Identify=FootSpace,"TextUnit=50.8 mm"
|
||||
Identify=DeadPath,"TextUnit=0 mm"
|
||||
Identify=Preset,"TextUnit=0 mm"
|
||||
Identify=Average,Choosing=1
|
||||
Identify=OCFactor,Choosing=0
|
||||
Identify=RangeType,Choosing=0
|
||||
Identify=SquareErr,"TextUnit=0 arcsec"
|
||||
Identify=RotAQBRes,Choosing=0
|
||||
Identify=ParaType,Choosing=0
|
||||
Identify=AllowKBPos,Choosing=0
|
||||
Identify=Hysteresis,ItemText=3
|
||||
Identify=Axis,Choosing=2
|
||||
Identify=AutoTitle,Choosing=1
|
||||
Identify=Mode,Choosing=0
|
||||
Identify=Cycles,ItemText=5
|
||||
Identify=StartPos,"TextUnit=1 mm"
|
||||
Identify=Interval,"TextUnit=1 mm"
|
||||
Identify=EndPos,"TextUnit=90 mm"
|
||||
Identify=Points,TextUnit=10
|
||||
Identify=UserDef,Choosing=1
|
||||
Identify=Positions,"TextUnit=1,10.89,20.7775,30.6675,40.555,50.445,60.3325,70.2225,80.11,90 mm",Expanded=N
|
||||
Identify=Axis2,Choosing=1
|
||||
Identify=Mode2,Choosing=0
|
||||
Identify=Cycles2,ItemText=5
|
||||
Identify=StartPos2,"TextUnit=0 mm"
|
||||
Identify=Interval2,"TextUnit=100 mm"
|
||||
Identify=EndPos2,"TextUnit=1000 mm"
|
||||
Identify=Points2,TextUnit=11
|
||||
Identify=UserDef2,Choosing=0
|
||||
Identify=Positions2,"TextUnit=0,100,200,300,400,500,600,700,800,900,1000 mm",Expanded=N
|
||||
Identify=TrigType,Choosing=2
|
||||
Identify=TrigWnd,"TextUnit=0.025 mm"
|
||||
Identify=TrigDwell,"TextUnit=4 sec"
|
||||
Identify=AQBMode,Choosing=0
|
||||
Identify=AQBRes,"TextUnit=1 um"
|
||||
Identify=EPTimeOut,ItemText=1.0
|
||||
Identify=AutoTimer,"TextUnit=1 sec"
|
||||
Identify=UnitSysSel,Choosing=0
|
||||
Identify=PosUnit,Choosing=0
|
||||
Identify=ErrUnit,Choosing=0
|
||||
Identify=ResultRes,Choosing=7
|
||||
Identify=ExpCoef,Choosing=0
|
||||
Identify=ExpCoef2,TextUnit=
|
||||
Identify=WayLength,"TextUnit=812.8 mm"
|
||||
Identify=WayDir,Choosing=0
|
||||
Identify=WayStaNum,ItemText=16
|
||||
Identify=FlaStaAC,ItemText=8
|
||||
Identify=FlaStaAG,ItemText=6
|
||||
Identify=FlaAxisDir,Choosing=0
|
||||
Identify=FlaLenAC,"TextUnit=812.8 mm"
|
||||
Identify=FlaLenAG,"TextUnit=609.6 mm"
|
||||
Identify=FlaLenAE,"TextUnit=1012 mm"
|
||||
Identify=FlaAllSta,"ItemText=20,20,16,12,16,12,16,12",Expanded=N
|
||||
Identify=DiaScaleX,TextUnit=4
|
||||
Identify=DiaScaleY,TextUnit=4
|
||||
Identify=DiaScaleZ,TextUnit=3
|
||||
Identify=AxisDirSel,ItemText=00000000
|
||||
Identify=AxisOrder,ItemText=1
|
||||
Identify=AxisDone,Comprise=Y,Expanded=N
|
||||
Identify=MeaAxisSel,ItemText=
|
||||
Identify=SameAs,Choosing=0
|
||||
Identify=TBDispSel,Comprise=YNNN,Expanded=N
|
||||
Identify=StartType,Choosing=0
|
||||
Identify=TBStartPos,"TextUnit=0 mm"
|
||||
Identify=StopType,Choosing=2
|
||||
Identify=TBStopPos,"TextUnit=100 mm"
|
||||
Identify=TBInterval,"TextUnit=0.1 sec"
|
||||
Identify=TotalTime,"TextUnit=10 sec"
|
||||
Identify=PointNum,ItemText=101
|
||||
Identify=ManualRH,Choosing=0
|
||||
Identify=EnvUnitSel,Choosing=0
|
||||
Identify=EnvUpdate,"TextUnit=10 sec"
|
||||
Identify=Standard,Choosing=12
|
||||
Identify=AnaMod,Choosing=1
|
||||
Identify=AnaGraph,Comprise=YYYYYYYNNY,Expanded=N
|
||||
Identify=AnaSigma,TextUnit=2
|
||||
Identify=AnaNum,Comprise=YYYYYNNYNNN,Expanded=N
|
||||
Identify=AnaSlope,Choosing=0
|
||||
Identify=PrnShowSel,Comprise=YYYY,Expanded=N
|
||||
Identify=PrnEnvSel,Choosing=0
|
||||
Identify=PrnCopies,ItemText=1
|
||||
Identify=PrnOrient,Choosing=0
|
||||
Identify=PrnMargin,Choosing=0
|
||||
Identify=TBDataPnt,Choosing=0
|
||||
Identify=FlaMethod,Choosing=0
|
||||
Identify=CompZero,ItemText=1
|
||||
Identify=Location,"ItemText=Mechatronics Lab"
|
||||
Identify=AssetNo,ItemText=
|
||||
Identify=Comments,"ItemText=TR-Electronics,EL5042_DC,ED7062_CSP,ClosedLoop,S-Curve,""100 microns step before position""",Expanded=N
|
||||
Identify=StartTime,"ItemText=07.09.2026 11:11:25"
|
||||
Identify=MachName,"ItemText=Test setup"
|
||||
Identify=MachType,ItemText=StepperMottor
|
||||
Identify=MachSN,ItemText=
|
||||
Identify=MachModel,ItemText=
|
||||
Identify=DateTest,"ItemText=07.09.2026 11:32:19"
|
||||
Identify=Operator,ItemText=Henrique
|
||||
Identify=MeaInst,ItemText=
|
||||
Identify=TypeScale,ItemText=
|
||||
Identify=NDECorr,Choosing=0
|
||||
Identify=FeedRate,"TextUnit=120 mm/min"
|
||||
Identify=DwellTime,"TextUnit=3 sec"
|
||||
Identify=CompUsed,ItemText=
|
||||
Identify=CoefScale,TextUnit=
|
||||
Identify=PosAxes,ItemText=
|
||||
Identify=ToolX,TextUnit=
|
||||
Identify=ToolY,TextUnit=
|
||||
Identify=ToolZ,TextUnit=
|
||||
Identify=PieceX,TextUnit=
|
||||
Identify=PieceY,TextUnit=
|
||||
Identify=PieceZ,TextUnit=
|
||||
Identify=MatSen1,ItemText=
|
||||
Identify=MatSen2,ItemText=
|
||||
Identify=MatSen3,ItemText=
|
||||
Identify=ATSen,ItemText=
|
||||
Identify=MeaLength,"TextUnit=90 mm"
|
||||
Identify=CalMeaDev,Choosing=0
|
||||
Identify=ErrorRange,"TextUnit=0.8 ppm"
|
||||
Identify=AlignErr,Choosing=0
|
||||
Identify=Diff20CMax,Choosing=1
|
||||
Identify=MatTempDev,Choosing=0
|
||||
Identify=UncExpCoef,"TextUnit=2 ppm/C"
|
||||
Identify=EnvVarErr,"TextUnit=0.0017 mm"
|
||||
Identify=CompRout,"TextUnit=4 sec"
|
||||
Identify=CompCalc,Choosing=0
|
||||
Identify=CompDir,Choosing=0
|
||||
Identify=CompSign,Choosing=0
|
||||
Identify=CompAbs,Choosing=0
|
||||
Identify=CompTI,Choosing=0
|
||||
Identify=MachUnit,"TextUnit=1 um"
|
||||
Identify=CompSel,Choosing=0
|
||||
Identify=CompStart,"TextUnit=1 mm"
|
||||
Identify=CompIntvl,"TextUnit=1 mm"
|
||||
Identify=CompEnd,"TextUnit=90 mm"
|
||||
Identify=UpperSel,Choosing=0
|
||||
Identify=LaserRes,"TextUnit=-0.1 um"
|
||||
Identify=LaserSen,Choosing=1
|
||||
Identify=ErrorRes,"TextUnit=-0.0001 mm"
|
||||
Identify=ComboRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=SpeedRes,"TextUnit=-0.01 mm/s"
|
||||
Identify=LaserRes2,"TextUnit=-0.01 um"
|
||||
Identify=LaserSen2,Choosing=1
|
||||
Identify=LowerSel,Choosing=3
|
||||
Identify=TargetRes,"TextUnit=-0.1 um"
|
||||
Identify=EncoderRes,"TextUnit=-0.01 um"
|
||||
Identify=RotaryRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=RotarySen,Choosing=1
|
||||
Identify=MidDispSel,Choosing=0
|
||||
Identify=GraPanel,"ItemText=Linear - Measurement Axis: Z"
|
||||
Identify=LimitSel,Choosing=1
|
||||
Identify=LimitLine,"TextUnit=0.01 mm"
|
||||
Identify=UserSel,Choosing=1
|
||||
Identify=UserScale,"TextUnit=0.1 mm"
|
||||
Identify=Legend,Choosing=1
|
||||
Identify=TarInRow,Choosing=1
|
||||
Identify=ResAxisSel,Choosing=0
|
||||
Identify=GridLines,Choosing=1
|
||||
Identify=Centered,Choosing=1
|
||||
Identify=FlaGraSel,Choosing=1
|
||||
Identify=ErrorSign,Choosing=0
|
||||
Identify=FirstRow,ItemText=1
|
||||
Identify=RefDisp,Choosing=2
|
||||
Identify=RotThita,"TextUnit=30 arcdeg"
|
||||
Identify=RotPhy,"TextUnit=15 arcdeg"
|
||||
Identify=FigRanges,"ItemText=0,-0.02,95,0.02",Expanded=N
|
||||
Identify=EnvRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvUser,Choosing=0
|
||||
Identify=DataGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=CompGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=LinearErr,"TextUnit=0.000994235,0.002595408,0.004028431,0.004816103,0.005103203,0.006362299,0.007658977,0.007429147,0.007142232,0.006172853,0.006177795,0.006885240,0.006904827,0.006759196,0.005493607,0.004204018,0.003899505,0.003061395,0.001582524,0.000575785,0.000577723,0.001927094,0.003600401,0.004191313,0.004574551,0.005711223,0.007184402,0.006913005,0.006916338,0.006246422,0.006247971,0.006520116,0.006545296,0.006477112,0.005159400,0.003757874,0.003437214,0.002750826,0.001343544,0.000149475,0.000151858,0.001716791,0.003247581,0.003981482,0.004252661,0.005374932,0.006760898,0.006862863,0.006651121,0.005922998,0.005915451,0.006360570,0.006433206,0.006250622,0.004805239,0.003642205,0.003396816,0.002441683,0.001252362,0.000016607,0.000019393,0.001617610,0.002772983,0.003713579,0.004251145,0.005231714,0.006552492,0.006764931,0.006578086,0.005627180,0.005638127,0.006149320,0.006296252,0.006150415,0.004664802,0.003582538,0.003208424,0.002149705,0.000880682,-0.000270009,-0.000269953,0.001328054,0.002749551,0.003612443,0.003984067,0.005081026,0.006525090,0.006560562,0.006358406,0.005765525,0.005778431,0.006059920,0.006054108,0.006049448,0.004422809,0.003266426,0.003082817,0.002043588,0.000713857,-0.000452453 mm",Expanded=N
|
||||
Identify=EnvDispSel,Choosing=4
|
||||
Identify=ATHistory,"TextUnit=22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.03,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.04,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.05,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06 C",Expanded=N
|
||||
Identify=APHistory,"TextUnit=738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.1,738.2,738.1,738.1,738.1,738.1,738.2,738.1,738.2,738.2,738.2,738.2,738.2,738.2,738.1,738.1,738.1,738.1,738.1,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.1,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.2,738.1,738.1,738.1,738.1,738.1 mmHg",Expanded=N
|
||||
Identify=RHHistory,"TextUnit=53,53,54,53,53,53,53,53,53,54,53,53,53,53,53,53,54,54,53,53,54,54,54,54,54,53,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54,54 %",Expanded=N
|
||||
Identify=MTHistory,"TextUnit=22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.15,22.16,22.15,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18 C",Expanded=N
|
||||
Identify=ProgHist,"ItemText=0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100",Expanded=N
|
||||
Identify=TimeHist,"ItemText=0,1,14,27,41,54,68,81,95,108,122,123,136,150,164,178,192,206,220,234,248,249,261,275,288,302,315,329,342,356,369,370,383,397,411,425,439,453,467,481,495,496,509,522,536,549,563,576,590,603,617,618,631,645,659,673,687,701,715,729,743,744,756,770,783,797,810,824,837,851,864,865,878,892,906,920,934,948,962,976,990,991,1004,1017,1031,1044,1058,1071,1085,1098,1112,1113,1126,1140,1154,1168,1182,1196,1210,1224,1238",Expanded=N
|
||||
Identify=NormRange,Choosing=1
|
||||
Identify=ATList,"TextUnit=22.03,,22.06,22.03,22.05,22.06 C",Expanded=N
|
||||
Identify=APList,"TextUnit=738.2,,738.2,738.1,738.2,738.1 mmHg",Expanded=N
|
||||
Identify=RHList,"TextUnit=53,,54,53,54,54 %",Expanded=N
|
||||
Identify=MT1List,"TextUnit=22.25,,22.28,22.25,22.26,22.28 C",Expanded=N
|
||||
Identify=MT2List,"TextUnit=22.05,,22.07,22.05,22.06,22.07 C",Expanded=N
|
||||
Identify=MT3List,"TextUnit=,,,,, C",Expanded=N
|
||||
Identify=EnvCount,ItemText=1254
|
||||
|
||||
<End of Option Description File - Rev. 1.00a>
|
||||
@@ -0,0 +1,201 @@
|
||||
<Option Description File - Rev. 1.00a - Keysight E1733A 1.14.1 (Win64)>
|
||||
UserSetup
|
||||
|
||||
Identify=MeaType,Choosing=0
|
||||
Identify=FileName,ItemText=OWIS_stageTR_Electronics_FAT_ISO230_Stepper_ED7062_CSV_EL5042_DC_ClosedLoop_SCurve_gap.Lin
|
||||
Identify=MergedFile,ItemText=
|
||||
Identify=CaliPeriod,"TextUnit=24 Month"
|
||||
Identify=SynchOp,Choosing=1
|
||||
Identify=RotaryDev,Choosing=1
|
||||
Identify=UserEdited,Choosing=0
|
||||
Identify=AutoScale,Choosing=0
|
||||
Identify=StopOnErr,Choosing=1
|
||||
Identify=StopOnLost,Choosing=0
|
||||
Identify=Extended,Choosing=1
|
||||
Identify=TargetSign,Choosing=0
|
||||
Identify=FootSpace,"TextUnit=50.8 mm"
|
||||
Identify=DeadPath,"TextUnit=0 mm"
|
||||
Identify=Preset,"TextUnit=0 mm"
|
||||
Identify=Average,Choosing=1
|
||||
Identify=OCFactor,Choosing=0
|
||||
Identify=RangeType,Choosing=0
|
||||
Identify=SquareErr,"TextUnit=0 arcsec"
|
||||
Identify=RotAQBRes,Choosing=0
|
||||
Identify=ParaType,Choosing=0
|
||||
Identify=AllowKBPos,Choosing=0
|
||||
Identify=Hysteresis,ItemText=3
|
||||
Identify=Axis,Choosing=2
|
||||
Identify=AutoTitle,Choosing=1
|
||||
Identify=Mode,Choosing=0
|
||||
Identify=Cycles,ItemText=5
|
||||
Identify=StartPos,"TextUnit=1 mm"
|
||||
Identify=Interval,"TextUnit=1 mm"
|
||||
Identify=EndPos,"TextUnit=90 mm"
|
||||
Identify=Points,TextUnit=10
|
||||
Identify=UserDef,Choosing=1
|
||||
Identify=Positions,"TextUnit=1,10.89,20.7775,30.6675,40.555,50.445,60.3325,70.2225,80.11,90 mm",Expanded=N
|
||||
Identify=Axis2,Choosing=1
|
||||
Identify=Mode2,Choosing=0
|
||||
Identify=Cycles2,ItemText=5
|
||||
Identify=StartPos2,"TextUnit=0 mm"
|
||||
Identify=Interval2,"TextUnit=100 mm"
|
||||
Identify=EndPos2,"TextUnit=1000 mm"
|
||||
Identify=Points2,TextUnit=11
|
||||
Identify=UserDef2,Choosing=0
|
||||
Identify=Positions2,"TextUnit=0,100,200,300,400,500,600,700,800,900,1000 mm",Expanded=N
|
||||
Identify=TrigType,Choosing=2
|
||||
Identify=TrigWnd,"TextUnit=0.025 mm"
|
||||
Identify=TrigDwell,"TextUnit=4 sec"
|
||||
Identify=AQBMode,Choosing=0
|
||||
Identify=AQBRes,"TextUnit=1 um"
|
||||
Identify=EPTimeOut,ItemText=1.0
|
||||
Identify=AutoTimer,"TextUnit=1 sec"
|
||||
Identify=UnitSysSel,Choosing=0
|
||||
Identify=PosUnit,Choosing=0
|
||||
Identify=ErrUnit,Choosing=0
|
||||
Identify=ResultRes,Choosing=7
|
||||
Identify=ExpCoef,Choosing=0
|
||||
Identify=ExpCoef2,TextUnit=
|
||||
Identify=WayLength,"TextUnit=812.8 mm"
|
||||
Identify=WayDir,Choosing=0
|
||||
Identify=WayStaNum,ItemText=16
|
||||
Identify=FlaStaAC,ItemText=8
|
||||
Identify=FlaStaAG,ItemText=6
|
||||
Identify=FlaAxisDir,Choosing=0
|
||||
Identify=FlaLenAC,"TextUnit=812.8 mm"
|
||||
Identify=FlaLenAG,"TextUnit=609.6 mm"
|
||||
Identify=FlaLenAE,"TextUnit=1012 mm"
|
||||
Identify=FlaAllSta,"ItemText=20,20,16,12,16,12,16,12",Expanded=N
|
||||
Identify=DiaScaleX,TextUnit=4
|
||||
Identify=DiaScaleY,TextUnit=4
|
||||
Identify=DiaScaleZ,TextUnit=3
|
||||
Identify=AxisDirSel,ItemText=00000000
|
||||
Identify=AxisOrder,ItemText=1
|
||||
Identify=AxisDone,Comprise=Y,Expanded=N
|
||||
Identify=MeaAxisSel,ItemText=
|
||||
Identify=SameAs,Choosing=0
|
||||
Identify=TBDispSel,Comprise=YNNN,Expanded=N
|
||||
Identify=StartType,Choosing=0
|
||||
Identify=TBStartPos,"TextUnit=0 mm"
|
||||
Identify=StopType,Choosing=2
|
||||
Identify=TBStopPos,"TextUnit=100 mm"
|
||||
Identify=TBInterval,"TextUnit=0.1 sec"
|
||||
Identify=TotalTime,"TextUnit=10 sec"
|
||||
Identify=PointNum,ItemText=101
|
||||
Identify=ManualRH,Choosing=0
|
||||
Identify=EnvUnitSel,Choosing=0
|
||||
Identify=EnvUpdate,"TextUnit=10 sec"
|
||||
Identify=Standard,Choosing=12
|
||||
Identify=AnaMod,Choosing=1
|
||||
Identify=AnaGraph,Comprise=YYYYYYYNNY,Expanded=N
|
||||
Identify=AnaSigma,TextUnit=2
|
||||
Identify=AnaNum,Comprise=YYYYYNNYNNN,Expanded=N
|
||||
Identify=AnaSlope,Choosing=0
|
||||
Identify=PrnShowSel,Comprise=YYYY,Expanded=N
|
||||
Identify=PrnEnvSel,Choosing=0
|
||||
Identify=PrnCopies,ItemText=1
|
||||
Identify=PrnOrient,Choosing=0
|
||||
Identify=PrnMargin,Choosing=0
|
||||
Identify=TBDataPnt,Choosing=0
|
||||
Identify=FlaMethod,Choosing=0
|
||||
Identify=CompZero,ItemText=1
|
||||
Identify=Location,"ItemText=Mechatronics Lab"
|
||||
Identify=AssetNo,ItemText=
|
||||
Identify=Comments,"ItemText=TR-Electronics,EL5042_DC,ED7062_CSV,ClosedLoop,S-Curve,""100 microns step before position""",Expanded=N
|
||||
Identify=StartTime,"ItemText=07.09.2026 09:41:38"
|
||||
Identify=MachName,"ItemText=Test setup"
|
||||
Identify=MachType,ItemText=StepperMottor
|
||||
Identify=MachSN,ItemText=
|
||||
Identify=MachModel,ItemText=
|
||||
Identify=DateTest,"ItemText=07.09.2026 10:02:27"
|
||||
Identify=Operator,ItemText=Henrique
|
||||
Identify=MeaInst,ItemText=
|
||||
Identify=TypeScale,ItemText=
|
||||
Identify=NDECorr,Choosing=0
|
||||
Identify=FeedRate,"TextUnit=120 mm/min"
|
||||
Identify=DwellTime,"TextUnit=3 sec"
|
||||
Identify=CompUsed,ItemText=
|
||||
Identify=CoefScale,TextUnit=
|
||||
Identify=PosAxes,ItemText=
|
||||
Identify=ToolX,TextUnit=
|
||||
Identify=ToolY,TextUnit=
|
||||
Identify=ToolZ,TextUnit=
|
||||
Identify=PieceX,TextUnit=
|
||||
Identify=PieceY,TextUnit=
|
||||
Identify=PieceZ,TextUnit=
|
||||
Identify=MatSen1,ItemText=
|
||||
Identify=MatSen2,ItemText=
|
||||
Identify=MatSen3,ItemText=
|
||||
Identify=ATSen,ItemText=
|
||||
Identify=MeaLength,"TextUnit=90 mm"
|
||||
Identify=CalMeaDev,Choosing=0
|
||||
Identify=ErrorRange,"TextUnit=0.8 ppm"
|
||||
Identify=AlignErr,Choosing=0
|
||||
Identify=Diff20CMax,Choosing=1
|
||||
Identify=MatTempDev,Choosing=0
|
||||
Identify=UncExpCoef,"TextUnit=2 ppm/C"
|
||||
Identify=EnvVarErr,"TextUnit=0.0017 mm"
|
||||
Identify=CompRout,"TextUnit=4 sec"
|
||||
Identify=CompCalc,Choosing=0
|
||||
Identify=CompDir,Choosing=0
|
||||
Identify=CompSign,Choosing=0
|
||||
Identify=CompAbs,Choosing=0
|
||||
Identify=CompTI,Choosing=0
|
||||
Identify=MachUnit,"TextUnit=1 um"
|
||||
Identify=CompSel,Choosing=0
|
||||
Identify=CompStart,"TextUnit=1 mm"
|
||||
Identify=CompIntvl,"TextUnit=1 mm"
|
||||
Identify=CompEnd,"TextUnit=90 mm"
|
||||
Identify=UpperSel,Choosing=0
|
||||
Identify=LaserRes,"TextUnit=-0.1 um"
|
||||
Identify=LaserSen,Choosing=1
|
||||
Identify=ErrorRes,"TextUnit=-0.0001 mm"
|
||||
Identify=ComboRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=SpeedRes,"TextUnit=-0.01 mm/s"
|
||||
Identify=LaserRes2,"TextUnit=-0.01 um"
|
||||
Identify=LaserSen2,Choosing=1
|
||||
Identify=LowerSel,Choosing=3
|
||||
Identify=TargetRes,"TextUnit=-0.1 um"
|
||||
Identify=EncoderRes,"TextUnit=-0.01 um"
|
||||
Identify=RotaryRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=RotarySen,Choosing=1
|
||||
Identify=MidDispSel,Choosing=0
|
||||
Identify=GraPanel,"ItemText=Linear - Measurement Axis: Z"
|
||||
Identify=LimitSel,Choosing=1
|
||||
Identify=LimitLine,"TextUnit=0.01 mm"
|
||||
Identify=UserSel,Choosing=1
|
||||
Identify=UserScale,"TextUnit=0.1 mm"
|
||||
Identify=Legend,Choosing=1
|
||||
Identify=TarInRow,Choosing=1
|
||||
Identify=ResAxisSel,Choosing=0
|
||||
Identify=GridLines,Choosing=1
|
||||
Identify=Centered,Choosing=1
|
||||
Identify=FlaGraSel,Choosing=1
|
||||
Identify=ErrorSign,Choosing=0
|
||||
Identify=FirstRow,ItemText=1
|
||||
Identify=RefDisp,Choosing=2
|
||||
Identify=RotThita,"TextUnit=30 arcdeg"
|
||||
Identify=RotPhy,"TextUnit=15 arcdeg"
|
||||
Identify=FigRanges,"ItemText=0,-0.02,95,0.02",Expanded=N
|
||||
Identify=EnvRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvUser,Choosing=0
|
||||
Identify=DataGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=CompGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=LinearErr,"TextUnit=0.001440800,0.002974017,0.004450408,0.005126797,0.004893900,0.005701863,0.007207494,0.006648095,0.006284393,0.005445580,0.005448663,0.006077500,0.006173470,0.005986274,0.004747928,0.003499263,0.003454139,0.002665161,0.001257751,0.000033137,0.000026264,0.001643127,0.002949337,0.003421497,0.003912059,0.004997334,0.006243385,0.006326520,0.006142238,0.005588395,0.005592324,0.005891462,0.006079765,0.005741912,0.004505973,0.003264929,0.002813408,0.002439311,0.000786288,-0.000459109,-0.000453150,0.001457338,0.002409130,0.003326406,0.003811224,0.004920681,0.006262303,0.006196076,0.006197014,0.005333921,0.005335107,0.005838874,0.006176159,0.005718964,0.004336468,0.003273399,0.002797293,0.002136376,0.000585292,-0.000666956,-0.000658292,0.001163927,0.002293383,0.003175265,0.003770570,0.004883629,0.006256995,0.006398930,0.006130271,0.005627573,0.005628881,0.005825934,0.006360913,0.005842409,0.004143910,0.003418992,0.002695897,0.002039241,0.000601383,-0.000835712,-0.000830812,0.000943799,0.002440872,0.003237568,0.003626113,0.004989473,0.006360533,0.006336904,0.006092409,0.005620711,0.005630463,0.005874344,0.006357194,0.005960076,0.004311065,0.003382925,0.002744836,0.002221686,0.000720614,-0.000781809 mm",Expanded=N
|
||||
Identify=EnvDispSel,Choosing=4
|
||||
Identify=ATHistory,"TextUnit=21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.86,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.87,21.88,21.88,21.88,21.87,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88,21.88 C",Expanded=N
|
||||
Identify=APHistory,"TextUnit=738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.4,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.5,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.6,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.7,738.6,738.6,738.6,738.7,738.7,738.6,738.6,738.6,738.6,738.6,738.7,738.7,738.6,738.6,738.6,738.6,738.7 mmHg",Expanded=N
|
||||
Identify=RHHistory,"TextUnit=53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53,53 %",Expanded=N
|
||||
Identify=MTHistory,"TextUnit=21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.98,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,21.99,22.00,22.00,21.99,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00,22.00 C",Expanded=N
|
||||
Identify=ProgHist,"ItemText=0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100",Expanded=N
|
||||
Identify=TimeHist,"ItemText=0,1,14,27,41,54,68,81,95,108,122,123,136,150,164,178,192,206,220,234,248,249,261,275,288,302,315,329,342,356,369,370,383,397,411,425,439,453,467,481,495,496,509,522,536,549,563,576,590,603,617,618,631,645,659,673,687,701,715,729,743,744,756,770,783,797,810,824,837,851,864,865,878,892,906,920,934,948,962,976,990,991,1004,1017,1031,1044,1058,1071,1085,1098,1112,1113,1126,1140,1154,1168,1182,1196,1210,1224,1238",Expanded=N
|
||||
Identify=NormRange,Choosing=1
|
||||
Identify=ATList,"TextUnit=21.86,,21.88,21.86,21.87,21.88 C",Expanded=N
|
||||
Identify=APList,"TextUnit=738.5,,738.7,738.3,738.6,738.6 mmHg",Expanded=N
|
||||
Identify=RHList,"TextUnit=53,,53,53,53,53 %",Expanded=N
|
||||
Identify=MT1List,"TextUnit=22.11,,22.13,22.11,22.12,22.13 C",Expanded=N
|
||||
Identify=MT2List,"TextUnit=21.84,,21.87,21.84,21.86,21.87 C",Expanded=N
|
||||
Identify=MT3List,"TextUnit=,,,,, C",Expanded=N
|
||||
Identify=EnvCount,ItemText=1251
|
||||
|
||||
<End of Option Description File - Rev. 1.00a>
|
||||
@@ -0,0 +1,201 @@
|
||||
<Option Description File - Rev. 1.00a - Keysight E1733A 1.14.1 (Win64)>
|
||||
UserSetup
|
||||
|
||||
Identify=MeaType,Choosing=0
|
||||
Identify=FileName,ItemText=OWIS_stageTR_Electronics_FAT_ISO230_Stepper_EL7041_EL5042.Lin
|
||||
Identify=MergedFile,ItemText=
|
||||
Identify=CaliPeriod,"TextUnit=12 Month"
|
||||
Identify=SynchOp,Choosing=1
|
||||
Identify=RotaryDev,Choosing=1
|
||||
Identify=UserEdited,Choosing=0
|
||||
Identify=AutoScale,Choosing=0
|
||||
Identify=StopOnErr,Choosing=1
|
||||
Identify=StopOnLost,Choosing=0
|
||||
Identify=Extended,Choosing=1
|
||||
Identify=TargetSign,Choosing=0
|
||||
Identify=FootSpace,"TextUnit=50.8 mm"
|
||||
Identify=DeadPath,"TextUnit=0 mm"
|
||||
Identify=Preset,"TextUnit=0 mm"
|
||||
Identify=Average,Choosing=1
|
||||
Identify=OCFactor,Choosing=0
|
||||
Identify=RangeType,Choosing=0
|
||||
Identify=SquareErr,"TextUnit=0 arcsec"
|
||||
Identify=RotAQBRes,Choosing=0
|
||||
Identify=ParaType,Choosing=0
|
||||
Identify=AllowKBPos,Choosing=0
|
||||
Identify=Hysteresis,ItemText=3
|
||||
Identify=Axis,Choosing=2
|
||||
Identify=AutoTitle,Choosing=1
|
||||
Identify=Mode,Choosing=0
|
||||
Identify=Cycles,ItemText=5
|
||||
Identify=StartPos,"TextUnit=1 mm"
|
||||
Identify=Interval,"TextUnit=1 mm"
|
||||
Identify=EndPos,"TextUnit=89.312 mm"
|
||||
Identify=Points,TextUnit=10
|
||||
Identify=UserDef,Choosing=1
|
||||
Identify=Positions,"TextUnit=1,11.773,18.755,30.982,42.674,49.344,62.56,71.617,77.436,89.312 mm",Expanded=N
|
||||
Identify=Axis2,Choosing=1
|
||||
Identify=Mode2,Choosing=0
|
||||
Identify=Cycles2,ItemText=5
|
||||
Identify=StartPos2,"TextUnit=0 mm"
|
||||
Identify=Interval2,"TextUnit=100 mm"
|
||||
Identify=EndPos2,"TextUnit=1000 mm"
|
||||
Identify=Points2,TextUnit=11
|
||||
Identify=UserDef2,Choosing=0
|
||||
Identify=Positions2,"TextUnit=0,100,200,300,400,500,600,700,800,900,1000 mm",Expanded=N
|
||||
Identify=TrigType,Choosing=2
|
||||
Identify=TrigWnd,"TextUnit=0.2 mm"
|
||||
Identify=TrigDwell,"TextUnit=4 sec"
|
||||
Identify=AQBMode,Choosing=0
|
||||
Identify=AQBRes,"TextUnit=1 um"
|
||||
Identify=EPTimeOut,ItemText=1.0
|
||||
Identify=AutoTimer,"TextUnit=1 sec"
|
||||
Identify=UnitSysSel,Choosing=0
|
||||
Identify=PosUnit,Choosing=0
|
||||
Identify=ErrUnit,Choosing=0
|
||||
Identify=ResultRes,Choosing=7
|
||||
Identify=ExpCoef,Choosing=0
|
||||
Identify=ExpCoef2,TextUnit=
|
||||
Identify=WayLength,"TextUnit=812.8 mm"
|
||||
Identify=WayDir,Choosing=0
|
||||
Identify=WayStaNum,ItemText=16
|
||||
Identify=FlaStaAC,ItemText=8
|
||||
Identify=FlaStaAG,ItemText=6
|
||||
Identify=FlaAxisDir,Choosing=0
|
||||
Identify=FlaLenAC,"TextUnit=812.8 mm"
|
||||
Identify=FlaLenAG,"TextUnit=609.6 mm"
|
||||
Identify=FlaLenAE,"TextUnit=1012 mm"
|
||||
Identify=FlaAllSta,"ItemText=20,20,16,12,16,12,16,12",Expanded=N
|
||||
Identify=DiaScaleX,TextUnit=4
|
||||
Identify=DiaScaleY,TextUnit=4
|
||||
Identify=DiaScaleZ,TextUnit=3
|
||||
Identify=AxisDirSel,ItemText=00000000
|
||||
Identify=AxisOrder,ItemText=1
|
||||
Identify=AxisDone,Comprise=Y,Expanded=N
|
||||
Identify=MeaAxisSel,ItemText=
|
||||
Identify=SameAs,Choosing=0
|
||||
Identify=TBDispSel,Comprise=YNNN,Expanded=N
|
||||
Identify=StartType,Choosing=0
|
||||
Identify=TBStartPos,"TextUnit=0 mm"
|
||||
Identify=StopType,Choosing=2
|
||||
Identify=TBStopPos,"TextUnit=100 mm"
|
||||
Identify=TBInterval,"TextUnit=0.1 sec"
|
||||
Identify=TotalTime,"TextUnit=10 sec"
|
||||
Identify=PointNum,ItemText=101
|
||||
Identify=ManualRH,Choosing=0
|
||||
Identify=EnvUnitSel,Choosing=0
|
||||
Identify=EnvUpdate,"TextUnit=10 sec"
|
||||
Identify=Standard,Choosing=12
|
||||
Identify=AnaMod,Choosing=1
|
||||
Identify=AnaGraph,Comprise=YYYYYYYNNY,Expanded=N
|
||||
Identify=AnaSigma,TextUnit=2
|
||||
Identify=AnaNum,Comprise=YYYYYNNYNNN,Expanded=N
|
||||
Identify=AnaSlope,Choosing=0
|
||||
Identify=PrnShowSel,Comprise=YYYY,Expanded=N
|
||||
Identify=PrnEnvSel,Choosing=0
|
||||
Identify=PrnCopies,ItemText=1
|
||||
Identify=PrnOrient,Choosing=0
|
||||
Identify=PrnMargin,Choosing=0
|
||||
Identify=TBDataPnt,Choosing=0
|
||||
Identify=FlaMethod,Choosing=0
|
||||
Identify=CompZero,ItemText=1
|
||||
Identify=Location,"ItemText=Mechatronics Lab"
|
||||
Identify=AssetNo,ItemText=
|
||||
Identify=Comments,"ItemText=TR-Electronics,EL5042,EL7041,closedLoop,S-Curve",Expanded=N
|
||||
Identify=StartTime,"ItemText=27.08.2026 10:35:24"
|
||||
Identify=MachName,"ItemText=Test setup"
|
||||
Identify=MachType,ItemText=StepperMottor
|
||||
Identify=MachSN,ItemText=
|
||||
Identify=MachModel,ItemText=
|
||||
Identify=DateTest,"ItemText=27.08.2026 10:54:19"
|
||||
Identify=Operator,ItemText=Henrique
|
||||
Identify=MeaInst,ItemText=
|
||||
Identify=TypeScale,ItemText=
|
||||
Identify=NDECorr,Choosing=0
|
||||
Identify=FeedRate,"TextUnit=120 mm/min"
|
||||
Identify=DwellTime,"TextUnit=3 sec"
|
||||
Identify=CompUsed,ItemText=
|
||||
Identify=CoefScale,TextUnit=
|
||||
Identify=PosAxes,ItemText=
|
||||
Identify=ToolX,TextUnit=
|
||||
Identify=ToolY,TextUnit=
|
||||
Identify=ToolZ,TextUnit=
|
||||
Identify=PieceX,TextUnit=
|
||||
Identify=PieceY,TextUnit=
|
||||
Identify=PieceZ,TextUnit=
|
||||
Identify=MatSen1,ItemText=
|
||||
Identify=MatSen2,ItemText=
|
||||
Identify=MatSen3,ItemText=
|
||||
Identify=ATSen,ItemText=
|
||||
Identify=MeaLength,"TextUnit=89.312 mm"
|
||||
Identify=CalMeaDev,Choosing=0
|
||||
Identify=ErrorRange,"TextUnit=0.8 ppm"
|
||||
Identify=AlignErr,Choosing=0
|
||||
Identify=Diff20CMax,Choosing=1
|
||||
Identify=MatTempDev,Choosing=0
|
||||
Identify=UncExpCoef,"TextUnit=2 ppm/C"
|
||||
Identify=EnvVarErr,"TextUnit=0.0017 mm"
|
||||
Identify=CompRout,"TextUnit=4 sec"
|
||||
Identify=CompCalc,Choosing=0
|
||||
Identify=CompDir,Choosing=0
|
||||
Identify=CompSign,Choosing=0
|
||||
Identify=CompAbs,Choosing=0
|
||||
Identify=CompTI,Choosing=0
|
||||
Identify=MachUnit,"TextUnit=1 um"
|
||||
Identify=CompSel,Choosing=0
|
||||
Identify=CompStart,"TextUnit=1 mm"
|
||||
Identify=CompIntvl,"TextUnit=1 mm"
|
||||
Identify=CompEnd,"TextUnit=89.312 mm"
|
||||
Identify=UpperSel,Choosing=0
|
||||
Identify=LaserRes,"TextUnit=-0.1 um"
|
||||
Identify=LaserSen,Choosing=1
|
||||
Identify=ErrorRes,"TextUnit=-0.0001 mm"
|
||||
Identify=ComboRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=SpeedRes,"TextUnit=-0.01 mm/s"
|
||||
Identify=LaserRes2,"TextUnit=-0.01 um"
|
||||
Identify=LaserSen2,Choosing=1
|
||||
Identify=LowerSel,Choosing=3
|
||||
Identify=TargetRes,"TextUnit=-0.1 um"
|
||||
Identify=EncoderRes,"TextUnit=-0.01 um"
|
||||
Identify=RotaryRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=RotarySen,Choosing=1
|
||||
Identify=MidDispSel,Choosing=0
|
||||
Identify=GraPanel,"ItemText=Linear - Measurement Axis: Z"
|
||||
Identify=LimitSel,Choosing=1
|
||||
Identify=LimitLine,"TextUnit=0.01 mm"
|
||||
Identify=UserSel,Choosing=1
|
||||
Identify=UserScale,"TextUnit=0.1 mm"
|
||||
Identify=Legend,Choosing=1
|
||||
Identify=TarInRow,Choosing=1
|
||||
Identify=ResAxisSel,Choosing=0
|
||||
Identify=GridLines,Choosing=1
|
||||
Identify=Centered,Choosing=1
|
||||
Identify=FlaGraSel,Choosing=1
|
||||
Identify=ErrorSign,Choosing=0
|
||||
Identify=FirstRow,ItemText=1
|
||||
Identify=RefDisp,Choosing=2
|
||||
Identify=RotThita,"TextUnit=30 arcdeg"
|
||||
Identify=RotPhy,"TextUnit=15 arcdeg"
|
||||
Identify=FigRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvUser,Choosing=0
|
||||
Identify=DataGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=CompGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=LinearErr,"TextUnit=0.001596587,0.002692864,0.001402576,-0.000595569,-0.002088399,-0.001876606,-0.002777320,-0.004391774,-0.004566598,-0.006595645,-0.006573541,-0.007449596,-0.006802074,-0.003573712,-0.002523636,-0.003262037,-0.001635291,0.000171451,0.001487028,0.000932380,0.000937827,-0.000475497,-0.001331578,-0.003052872,-0.004696503,-0.004177096,-0.005507850,-0.006421660,-0.006035635,-0.008834924,-0.008827866,-0.004750833,-0.004953997,-0.003284863,-0.002347948,-0.003087027,-0.001460024,0.000242832,0.001507707,0.000943546,0.000933272,-0.000594191,-0.001366937,-0.003169314,-0.004923559,-0.004224448,-0.005519703,-0.005266130,-0.006077565,-0.008525623,-0.008508133,-0.004460332,-0.005132435,-0.003415587,-0.002189586,-0.003002913,-0.001516132,0.000267918,0.001751935,0.000952906,0.000956730,-0.000440707,-0.001235613,-0.003014112,-0.004391984,-0.003886062,-0.005221162,-0.006042263,-0.005629210,-0.008429608,-0.008415418,-0.003840578,-0.004642029,-0.004988247,-0.002073362,-0.002544997,-0.001247580,0.000789305,0.002160610,0.001428912,0.001429855,0.000036022,-0.000903406,-0.002578481,-0.004266920,-0.003594794,-0.005028697,-0.004576637,-0.005441396,-0.008251731,-0.008246117,-0.003758622,-0.004390792,-0.004801846,-0.001873625,-0.002534203,-0.000778867,0.000950938,0.002294916,0.001815607 mm",Expanded=N
|
||||
Identify=EnvDispSel,Choosing=4
|
||||
Identify=ATHistory,"TextUnit=22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14,22.14 C",Expanded=N
|
||||
Identify=APHistory,"TextUnit=734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4,734.4 mmHg",Expanded=N
|
||||
Identify=RHHistory,"TextUnit=33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33,33 %",Expanded=N
|
||||
Identify=MTHistory,"TextUnit=22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93,22.93 C",Expanded=N
|
||||
Identify=ProgHist,"ItemText=0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100",Expanded=N
|
||||
Identify=TimeHist,"ItemText=0,1,13,26,41,56,69,85,99,111,126,127,142,154,168,182,192,205,219,230,242,243,255,266,280,293,303,317,329,339,352,353,365,375,387,401,412,425,438,449,462,463,474,485,499,512,523,537,549,560,573,574,586,596,608,622,633,646,659,670,683,684,695,706,720,733,743,757,769,779,792,793,806,816,828,843,853,866,880,890,903,904,916,927,941,954,964,978,990,1001,1014,1015,1028,1038,1050,1065,1075,1088,1102,1113,1125",Expanded=N
|
||||
Identify=NormRange,Choosing=1
|
||||
Identify=ATList,"TextUnit=22.14,,22.14,22.14,22.14,22.14 C",Expanded=N
|
||||
Identify=APList,"TextUnit=734.4,,734.4,734.4,734.4,734.4 mmHg",Expanded=N
|
||||
Identify=RHList,"TextUnit=33,,33,33,33,33 %",Expanded=N
|
||||
Identify=MT1List,"TextUnit=22.74,,22.74,22.74,22.74,22.74 C",Expanded=N
|
||||
Identify=MT2List,"TextUnit=23.11,,23.11,23.11,23.11,23.11 C",Expanded=N
|
||||
Identify=MT3List,"TextUnit=,,,,, C",Expanded=N
|
||||
Identify=EnvCount,ItemText=1135
|
||||
|
||||
<End of Option Description File - Rev. 1.00a>
|
||||
@@ -0,0 +1,201 @@
|
||||
<Option Description File - Rev. 1.00a - Keysight E1733A 1.14.1 (Win64)>
|
||||
UserSetup
|
||||
|
||||
Identify=MeaType,Choosing=2
|
||||
Identify=FileName,ItemText=OWIS_stageTR_Electronics_FAT_Straightness_Horizontal_XZ.Str
|
||||
Identify=MergedFile,ItemText=
|
||||
Identify=CaliPeriod,"TextUnit=12 Month"
|
||||
Identify=SynchOp,Choosing=1
|
||||
Identify=RotaryDev,Choosing=1
|
||||
Identify=UserEdited,Choosing=0
|
||||
Identify=AutoScale,Choosing=0
|
||||
Identify=StopOnErr,Choosing=1
|
||||
Identify=StopOnLost,Choosing=0
|
||||
Identify=Extended,Choosing=1
|
||||
Identify=TargetSign,Choosing=0
|
||||
Identify=FootSpace,"TextUnit=50.8 mm"
|
||||
Identify=DeadPath,"TextUnit=0 mm"
|
||||
Identify=Preset,"TextUnit=0 mm"
|
||||
Identify=Average,Choosing=1
|
||||
Identify=OCFactor,Choosing=0
|
||||
Identify=RangeType,Choosing=0
|
||||
Identify=SquareErr,"TextUnit=0 arcsec"
|
||||
Identify=RotAQBRes,Choosing=0
|
||||
Identify=ParaType,Choosing=0
|
||||
Identify=AllowKBPos,Choosing=0
|
||||
Identify=Hysteresis,ItemText=3
|
||||
Identify=Axis,Choosing=2
|
||||
Identify=AutoTitle,Choosing=1
|
||||
Identify=Mode,Choosing=0
|
||||
Identify=Cycles,ItemText=5
|
||||
Identify=StartPos,"TextUnit=1 mm"
|
||||
Identify=Interval,"TextUnit=9.88888889 mm"
|
||||
Identify=EndPos,"TextUnit=86 mm"
|
||||
Identify=Points,TextUnit=18
|
||||
Identify=UserDef,Choosing=1
|
||||
Identify=Positions,"TextUnit=1,6,11,16,21,26,31,36,41,46,51,56,61,66,71,76,81,86 mm",Expanded=N
|
||||
Identify=Axis2,Choosing=1
|
||||
Identify=Mode2,Choosing=0
|
||||
Identify=Cycles2,ItemText=5
|
||||
Identify=StartPos2,"TextUnit=0 mm"
|
||||
Identify=Interval2,"TextUnit=100 mm"
|
||||
Identify=EndPos2,"TextUnit=1000 mm"
|
||||
Identify=Points2,TextUnit=11
|
||||
Identify=UserDef2,Choosing=0
|
||||
Identify=Positions2,"TextUnit=0,100,200,300,400,500,600,700,800,900,1000 mm",Expanded=N
|
||||
Identify=TrigType,Choosing=0
|
||||
Identify=TrigWnd,"TextUnit=0.5 mm"
|
||||
Identify=TrigDwell,"TextUnit=1 sec"
|
||||
Identify=AQBMode,Choosing=0
|
||||
Identify=AQBRes,"TextUnit=1 um"
|
||||
Identify=EPTimeOut,Choosing=0
|
||||
Identify=AutoTimer,"TextUnit=1 sec"
|
||||
Identify=UnitSysSel,Choosing=0
|
||||
Identify=PosUnit,Choosing=0
|
||||
Identify=ErrUnit,Choosing=1
|
||||
Identify=ResultRes,Choosing=0
|
||||
Identify=ExpCoef,Choosing=0
|
||||
Identify=ExpCoef2,TextUnit=
|
||||
Identify=WayLength,"TextUnit=812.8 mm"
|
||||
Identify=WayDir,Choosing=0
|
||||
Identify=WayStaNum,ItemText=16
|
||||
Identify=FlaStaAC,ItemText=8
|
||||
Identify=FlaStaAG,ItemText=6
|
||||
Identify=FlaAxisDir,Choosing=0
|
||||
Identify=FlaLenAC,"TextUnit=812.8 mm"
|
||||
Identify=FlaLenAG,"TextUnit=609.6 mm"
|
||||
Identify=FlaLenAE,"TextUnit=1012 mm"
|
||||
Identify=FlaAllSta,"ItemText=20,20,16,12,16,12,16,12",Expanded=N
|
||||
Identify=DiaScaleX,TextUnit=4
|
||||
Identify=DiaScaleY,TextUnit=4
|
||||
Identify=DiaScaleZ,TextUnit=3
|
||||
Identify=AxisDirSel,ItemText=00000000
|
||||
Identify=AxisOrder,ItemText=1
|
||||
Identify=AxisDone,Comprise=Y,Expanded=N
|
||||
Identify=MeaAxisSel,ItemText=
|
||||
Identify=SameAs,Choosing=0
|
||||
Identify=TBDispSel,Comprise=YNNN,Expanded=N
|
||||
Identify=StartType,Choosing=0
|
||||
Identify=TBStartPos,"TextUnit=0 mm"
|
||||
Identify=StopType,Choosing=2
|
||||
Identify=TBStopPos,"TextUnit=100 mm"
|
||||
Identify=TBInterval,"TextUnit=0.1 sec"
|
||||
Identify=TotalTime,"TextUnit=10 sec"
|
||||
Identify=PointNum,ItemText=101
|
||||
Identify=ManualRH,Choosing=0
|
||||
Identify=EnvUnitSel,Choosing=0
|
||||
Identify=EnvUpdate,"TextUnit=10 sec"
|
||||
Identify=Standard,Choosing=7
|
||||
Identify=AnaMod,Choosing=0
|
||||
Identify=AnaGraph,Comprise=YYYYYYYNNN,Expanded=N
|
||||
Identify=AnaSigma,TextUnit=2
|
||||
Identify=AnaNum,Comprise=YYYYYNNYNNN,Expanded=N
|
||||
Identify=AnaSlope,Choosing=0
|
||||
Identify=PrnShowSel,Comprise=YYYY,Expanded=N
|
||||
Identify=PrnEnvSel,Choosing=0
|
||||
Identify=PrnCopies,ItemText=1
|
||||
Identify=PrnOrient,Choosing=0
|
||||
Identify=PrnMargin,Choosing=0
|
||||
Identify=TBDataPnt,Choosing=0
|
||||
Identify=FlaMethod,Choosing=0
|
||||
Identify=CompZero,ItemText=1
|
||||
Identify=Location,"ItemText=Mechatronics Lab"
|
||||
Identify=AssetNo,ItemText=
|
||||
Identify=Comments,"ItemText=""TR-Electronics Encoder"",EL5042_DC,ED7062_CSP,""Horizontal XZ plane""",Expanded=N
|
||||
Identify=StartTime,"ItemText=08.09.2026 10:39:50"
|
||||
Identify=MachName,"ItemText=Owis Stage"
|
||||
Identify=MachType,"ItemText=Stepper Motor"
|
||||
Identify=MachSN,ItemText=
|
||||
Identify=MachModel,ItemText=
|
||||
Identify=DateTest,"ItemText=08.09.2026 11:12:37"
|
||||
Identify=Operator,ItemText=Henrique
|
||||
Identify=MeaInst,ItemText=
|
||||
Identify=TypeScale,ItemText=
|
||||
Identify=NDECorr,Choosing=0
|
||||
Identify=FeedRate,"TextUnit=180 mm/min"
|
||||
Identify=DwellTime,"TextUnit=2 sec"
|
||||
Identify=CompUsed,ItemText=
|
||||
Identify=CoefScale,TextUnit=
|
||||
Identify=PosAxes,ItemText=
|
||||
Identify=ToolX,TextUnit=
|
||||
Identify=ToolY,TextUnit=
|
||||
Identify=ToolZ,TextUnit=
|
||||
Identify=PieceX,TextUnit=
|
||||
Identify=PieceY,TextUnit=
|
||||
Identify=PieceZ,TextUnit=
|
||||
Identify=MatSen1,ItemText=
|
||||
Identify=MatSen2,ItemText=
|
||||
Identify=MatSen3,ItemText=
|
||||
Identify=ATSen,ItemText=
|
||||
Identify=MeaLength,"TextUnit=86 mm"
|
||||
Identify=CalMeaDev,Choosing=0
|
||||
Identify=ErrorRange,"TextUnit=0.8 ppm"
|
||||
Identify=AlignErr,Choosing=0
|
||||
Identify=Diff20CMax,Choosing=1
|
||||
Identify=MatTempDev,Choosing=0
|
||||
Identify=UncExpCoef,"TextUnit=2 ppm/C"
|
||||
Identify=EnvVarErr,"TextUnit=1.7 um"
|
||||
Identify=CompRout,"TextUnit=4 sec"
|
||||
Identify=CompCalc,Choosing=0
|
||||
Identify=CompDir,Choosing=0
|
||||
Identify=CompSign,Choosing=0
|
||||
Identify=CompAbs,Choosing=0
|
||||
Identify=CompTI,Choosing=0
|
||||
Identify=MachUnit,"TextUnit=1 um"
|
||||
Identify=CompSel,Choosing=0
|
||||
Identify=CompStart,"TextUnit=1 mm"
|
||||
Identify=CompIntvl,"TextUnit=9.88888889 mm"
|
||||
Identify=CompEnd,"TextUnit=86 mm"
|
||||
Identify=UpperSel,Choosing=0
|
||||
Identify=LaserRes,"TextUnit=-0.1 um"
|
||||
Identify=LaserSen,Choosing=1
|
||||
Identify=ErrorRes,"TextUnit=-0.1 um"
|
||||
Identify=ComboRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=SpeedRes,"TextUnit=-0.01 mm/s"
|
||||
Identify=LaserRes2,"TextUnit=-0.01 um"
|
||||
Identify=LaserSen2,Choosing=1
|
||||
Identify=LowerSel,Choosing=3
|
||||
Identify=TargetRes,"TextUnit=-0.01 um"
|
||||
Identify=EncoderRes,"TextUnit=-0.01 um"
|
||||
Identify=RotaryRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=RotarySen,Choosing=1
|
||||
Identify=MidDispSel,Choosing=0
|
||||
Identify=GraPanel,"ItemText=Straightness - Measurement Axis: Z"
|
||||
Identify=LimitSel,Choosing=0
|
||||
Identify=LimitLine,"TextUnit=25 um"
|
||||
Identify=UserSel,Choosing=0
|
||||
Identify=UserScale,"TextUnit=100 um"
|
||||
Identify=Legend,Choosing=1
|
||||
Identify=TarInRow,Choosing=1
|
||||
Identify=ResAxisSel,Choosing=0
|
||||
Identify=GridLines,Choosing=1
|
||||
Identify=Centered,Choosing=1
|
||||
Identify=FlaGraSel,Choosing=1
|
||||
Identify=ErrorSign,Choosing=0
|
||||
Identify=FirstRow,ItemText=1
|
||||
Identify=RefDisp,Choosing=2
|
||||
Identify=RotThita,"TextUnit=30 arcdeg"
|
||||
Identify=RotPhy,"TextUnit=15 arcdeg"
|
||||
Identify=FigRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvUser,Choosing=0
|
||||
Identify=DataGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=CompGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=LinearErr,"TextUnit=-0.0881,-1.1387,-2.4187,-2.8612,-3.8111,-4.5402,-4.8424,-5.1013,-5.6721,-6.0568,-7.0473,-6.8168,-7.5313,-7.8235,-7.7958,-8.7668,-9.2412,-10.1033,-10.2070,-9.3098,-8.2351,-8.0094,-7.1465,-7.6430,-6.9017,-5.2319,-6.7423,-4.4755,-4.3983,-4.1328,-4.1837,-3.3671,-0.4243,-0.1161,-0.6771,-0.3288,-0.8902,-1.4654,-1.5917,-2.8771,-2.9387,-4.3833,-3.0965,-4.8246,-4.7290,-6.2717,-5.8820,-6.5718,-6.2336,-6.7114,-7.0304,-8.8281,-8.4939,-11.0892,-10.9646,-8.8750,-8.8664,-7.7955,-7.3296,-6.9523,-7.5120,-4.8509,-6.5179,-2.6555,-5.5120,-4.5157,-3.7881,-4.3973,-1.9146,-1.0812,2.1826,-1.2046,1.9548,-2.4460,0.4225,-0.4055,-2.3672,-3.4981,-1.8201,-3.4823,-4.0171,-4.8900,-3.5497,-8.9204,-8.0884,-8.3361,-8.0566,-8.2369,-8.3681,-9.8812,-8.6580,-9.1855,-8.2702,-8.2640,-6.1625,-5.8563,-7.3927,-6.8092,-5.6800,-4.1461,-3.3341,-1.2190,-2.5256,-4.2932,-1.1474,1.0498,-0.5428,-0.8182,0.9621,-0.4044,-2.5196,-1.3116,-1.6262,-4.4690,-3.4822,-5.0159,-4.9037,-4.5393,-4.8669,-4.9353,-7.5426,-6.6178,-7.7379,-8.9430,-7.9259,-8.7831,-9.5916,-6.6854,-10.1703,-9.2525,-7.8213,-8.0682,-5.8627,-3.0995,-6.3121,-2.9867,-5.9261,-4.2125,-4.3784,-1.2683,2.1563,0.5735,0.5010,1.5437,0.3432,-1.1392,1.2454,-2.8815,-2.8297,-0.5406,-5.8656,-3.6737,-7.0341,-4.8744,-6.8783,-7.4902,-8.4416,-7.0861,-6.1431,-7.0219,-8.4250,-10.6446,-8.9596,-8.2236,-8.2288,-7.7329,-8.6908,-6.4195,-6.7164,-3.9870,-5.3535,-4.2747,-2.5600,-3.9365,-2.9549,-3.6811,-0.8363,4.4722,0.4430,1.6883 um",Expanded=N
|
||||
Identify=EnvDispSel,Choosing=0
|
||||
Identify=ATHistory,"TextUnit=22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.06,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.07,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.08,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.09,22.10,22.09,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.10,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.11,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.12,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.13,22.14,22.14,22.14,22.14 C",Expanded=N
|
||||
Identify=APHistory,"TextUnit=732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.5,732.4,732.4,732.5,732.4,732.5,732.5,732.4,732.4,732.4,732.5,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.4,732.3,732.4,732.4,732.3,732.3,732.3,732.4,732.3,732.3,732.3,732.3,732.4,732.4,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.4,732.4,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.3,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2,732.2 mmHg",Expanded=N
|
||||
Identify=RHHistory,"TextUnit=58,58,58,58,57,58,58,58,58,58,58,58,58,57,58,58,58,58,58,58,57,58,57,58,58,58,58,57,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,57,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,58,57,58,58,58,58,58,58,58,58,58,58,57,58,58,58,58,58,58,58,58,58,58,58,58,58,58,57,58,58,58,58,58,57,58,58,58,58,57,58,58,57,58,57,58,58,57,57,57,58,58,58,57,57,57,58,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57,57 %",Expanded=N
|
||||
Identify=MTHistory,"TextUnit=22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.16,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.17,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.18,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.19,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.20,22.21,22.21,22.21,22.21,22.21,22.21,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.22,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.23,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.24,22.25,22.25,22.25,22.25,22.25,22.25,22.25,22.25,22.25,22.25 C",Expanded=N
|
||||
Identify=ProgHist,"ItemText=0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,133,134,135,136,137,138,139,140,141,142,143,144,145,146,147,148,149,150,151,152,153,154,155,156,157,158,159,160,161,162,163,164,165,166,167,168,169,170,171,172,173,174,175,176,177,178,179,180",Expanded=N
|
||||
Identify=TimeHist,"ItemText=0,1,18,29,40,50,61,71,82,92,103,113,124,134,145,155,166,176,187,191,212,223,233,244,254,265,275,286,296,307,317,328,338,349,359,370,380,385,406,417,427,438,448,459,469,480,490,501,511,522,532,543,553,564,574,579,600,611,621,632,642,653,663,674,684,695,705,716,726,737,747,758,768,773,794,805,815,826,836,847,857,868,878,889,899,910,920,931,941,952,962,967,988,999,1009,1020,1030,1041,1051,1062,1072,1082,1093,1104,1114,1125,1135,1145,1156,1161,1182,1192,1203,1213,1224,1234,1245,1256,1266,1277,1287,1298,1308,1319,1329,1340,1350,1355,1376,1386,1397,1408,1418,1428,1439,1449,1460,1471,1481,1491,1502,1512,1523,1533,1544,1548,1562,1572,1583,1593,1604,1614,1625,1635,1646,1656,1667,1677,1688,1698,1709,1720,1730,1734,1756,1766,1777,1787,1798,1808,1819,1829,1839,1850,1861,1871,1882,1892,1903,1913,1924",Expanded=N
|
||||
Identify=NormRange,Choosing=1
|
||||
Identify=ATList,"TextUnit=22.06,,22.14,22.06,22.10,22.14 C",Expanded=N
|
||||
Identify=APList,"TextUnit=732.5,,732.5,732.2,732.4,732.2 mmHg",Expanded=N
|
||||
Identify=RHList,"TextUnit=58,,58,57,58,57 %",Expanded=N
|
||||
Identify=MT1List,"TextUnit=22.29,,22.36,22.29,22.32,22.36 C",Expanded=N
|
||||
Identify=MT2List,"TextUnit=22.02,,22.13,22.02,22.08,22.13 C",Expanded=N
|
||||
Identify=MT3List,"TextUnit=,,,,, C",Expanded=N
|
||||
Identify=EnvCount,ItemText=1960
|
||||
|
||||
<End of Option Description File - Rev. 1.00a>
|
||||
@@ -0,0 +1,201 @@
|
||||
<Option Description File - Rev. 1.00a - Keysight E1733A 1.14.1 (Win64)>
|
||||
UserSetup
|
||||
|
||||
Identify=MeaType,Choosing=2
|
||||
Identify=FileName,ItemText=OWIS_stageTR_Electronics_FAT_Straightness_Vertical_YZ.Str
|
||||
Identify=MergedFile,ItemText=
|
||||
Identify=CaliPeriod,"TextUnit=12 Month"
|
||||
Identify=SynchOp,Choosing=1
|
||||
Identify=RotaryDev,Choosing=1
|
||||
Identify=UserEdited,Choosing=0
|
||||
Identify=AutoScale,Choosing=0
|
||||
Identify=StopOnErr,Choosing=1
|
||||
Identify=StopOnLost,Choosing=0
|
||||
Identify=Extended,Choosing=1
|
||||
Identify=TargetSign,Choosing=0
|
||||
Identify=FootSpace,"TextUnit=50.8 mm"
|
||||
Identify=DeadPath,"TextUnit=0 mm"
|
||||
Identify=Preset,"TextUnit=0 mm"
|
||||
Identify=Average,Choosing=1
|
||||
Identify=OCFactor,Choosing=0
|
||||
Identify=RangeType,Choosing=0
|
||||
Identify=SquareErr,"TextUnit=0 arcsec"
|
||||
Identify=RotAQBRes,Choosing=0
|
||||
Identify=ParaType,Choosing=0
|
||||
Identify=AllowKBPos,Choosing=0
|
||||
Identify=Hysteresis,ItemText=3
|
||||
Identify=Axis,Choosing=2
|
||||
Identify=AutoTitle,Choosing=1
|
||||
Identify=Mode,Choosing=0
|
||||
Identify=Cycles,ItemText=5
|
||||
Identify=StartPos,"TextUnit=1 mm"
|
||||
Identify=Interval,"TextUnit=9.88888889 mm"
|
||||
Identify=EndPos,"TextUnit=86 mm"
|
||||
Identify=Points,TextUnit=18
|
||||
Identify=UserDef,Choosing=1
|
||||
Identify=Positions,"TextUnit=1,6,11,16,21,26,31,36,41,46,51,56,61,66,71,76,81,86 mm",Expanded=N
|
||||
Identify=Axis2,Choosing=1
|
||||
Identify=Mode2,Choosing=0
|
||||
Identify=Cycles2,ItemText=5
|
||||
Identify=StartPos2,"TextUnit=0 mm"
|
||||
Identify=Interval2,"TextUnit=100 mm"
|
||||
Identify=EndPos2,"TextUnit=1000 mm"
|
||||
Identify=Points2,TextUnit=11
|
||||
Identify=UserDef2,Choosing=0
|
||||
Identify=Positions2,"TextUnit=0,100,200,300,400,500,600,700,800,900,1000 mm",Expanded=N
|
||||
Identify=TrigType,Choosing=0
|
||||
Identify=TrigWnd,"TextUnit=0.5 mm"
|
||||
Identify=TrigDwell,"TextUnit=1 sec"
|
||||
Identify=AQBMode,Choosing=0
|
||||
Identify=AQBRes,"TextUnit=1 um"
|
||||
Identify=EPTimeOut,Choosing=0
|
||||
Identify=AutoTimer,"TextUnit=1 sec"
|
||||
Identify=UnitSysSel,Choosing=0
|
||||
Identify=PosUnit,Choosing=0
|
||||
Identify=ErrUnit,Choosing=1
|
||||
Identify=ResultRes,Choosing=0
|
||||
Identify=ExpCoef,Choosing=0
|
||||
Identify=ExpCoef2,TextUnit=
|
||||
Identify=WayLength,"TextUnit=812.8 mm"
|
||||
Identify=WayDir,Choosing=0
|
||||
Identify=WayStaNum,ItemText=16
|
||||
Identify=FlaStaAC,ItemText=8
|
||||
Identify=FlaStaAG,ItemText=6
|
||||
Identify=FlaAxisDir,Choosing=0
|
||||
Identify=FlaLenAC,"TextUnit=812.8 mm"
|
||||
Identify=FlaLenAG,"TextUnit=609.6 mm"
|
||||
Identify=FlaLenAE,"TextUnit=1012 mm"
|
||||
Identify=FlaAllSta,"ItemText=20,20,16,12,16,12,16,12",Expanded=N
|
||||
Identify=DiaScaleX,TextUnit=4
|
||||
Identify=DiaScaleY,TextUnit=4
|
||||
Identify=DiaScaleZ,TextUnit=3
|
||||
Identify=AxisDirSel,ItemText=00000000
|
||||
Identify=AxisOrder,ItemText=1
|
||||
Identify=AxisDone,Comprise=Y,Expanded=N
|
||||
Identify=MeaAxisSel,ItemText=
|
||||
Identify=SameAs,Choosing=0
|
||||
Identify=TBDispSel,Comprise=YNNN,Expanded=N
|
||||
Identify=StartType,Choosing=0
|
||||
Identify=TBStartPos,"TextUnit=0 mm"
|
||||
Identify=StopType,Choosing=2
|
||||
Identify=TBStopPos,"TextUnit=100 mm"
|
||||
Identify=TBInterval,"TextUnit=0.1 sec"
|
||||
Identify=TotalTime,"TextUnit=10 sec"
|
||||
Identify=PointNum,ItemText=101
|
||||
Identify=ManualRH,Choosing=0
|
||||
Identify=EnvUnitSel,Choosing=0
|
||||
Identify=EnvUpdate,"TextUnit=10 sec"
|
||||
Identify=Standard,Choosing=7
|
||||
Identify=AnaMod,Choosing=0
|
||||
Identify=AnaGraph,Comprise=YYYYYYYNNN,Expanded=N
|
||||
Identify=AnaSigma,TextUnit=2
|
||||
Identify=AnaNum,Comprise=YYYYYNNYNNN,Expanded=N
|
||||
Identify=AnaSlope,Choosing=0
|
||||
Identify=PrnShowSel,Comprise=YYYY,Expanded=N
|
||||
Identify=PrnEnvSel,Choosing=0
|
||||
Identify=PrnCopies,ItemText=1
|
||||
Identify=PrnOrient,Choosing=0
|
||||
Identify=PrnMargin,Choosing=0
|
||||
Identify=TBDataPnt,Choosing=0
|
||||
Identify=FlaMethod,Choosing=0
|
||||
Identify=CompZero,ItemText=1
|
||||
Identify=Location,"ItemText=Mechatronics Lab"
|
||||
Identify=AssetNo,ItemText=
|
||||
Identify=Comments,"ItemText=""TR-Electronics Encoder"",EL5042_DC,ED7062_CSP,""Vertical YZ plane""",Expanded=N
|
||||
Identify=StartTime,"ItemText=08.09.2026 13:18:25"
|
||||
Identify=MachName,"ItemText=Owis Stage"
|
||||
Identify=MachType,"ItemText=Stepper Motor"
|
||||
Identify=MachSN,ItemText=
|
||||
Identify=MachModel,ItemText=
|
||||
Identify=DateTest,"ItemText=08.09.2026 13:49:48"
|
||||
Identify=Operator,ItemText=Henrique
|
||||
Identify=MeaInst,ItemText=
|
||||
Identify=TypeScale,ItemText=
|
||||
Identify=NDECorr,Choosing=0
|
||||
Identify=FeedRate,"TextUnit=180 mm/min"
|
||||
Identify=DwellTime,"TextUnit=2 sec"
|
||||
Identify=CompUsed,ItemText=
|
||||
Identify=CoefScale,TextUnit=
|
||||
Identify=PosAxes,ItemText=
|
||||
Identify=ToolX,TextUnit=
|
||||
Identify=ToolY,TextUnit=
|
||||
Identify=ToolZ,TextUnit=
|
||||
Identify=PieceX,TextUnit=
|
||||
Identify=PieceY,TextUnit=
|
||||
Identify=PieceZ,TextUnit=
|
||||
Identify=MatSen1,ItemText=
|
||||
Identify=MatSen2,ItemText=
|
||||
Identify=MatSen3,ItemText=
|
||||
Identify=ATSen,ItemText=
|
||||
Identify=MeaLength,"TextUnit=86 mm"
|
||||
Identify=CalMeaDev,Choosing=0
|
||||
Identify=ErrorRange,"TextUnit=0.8 ppm"
|
||||
Identify=AlignErr,Choosing=0
|
||||
Identify=Diff20CMax,Choosing=1
|
||||
Identify=MatTempDev,Choosing=0
|
||||
Identify=UncExpCoef,"TextUnit=2 ppm/C"
|
||||
Identify=EnvVarErr,"TextUnit=1.7 um"
|
||||
Identify=CompRout,"TextUnit=4 sec"
|
||||
Identify=CompCalc,Choosing=0
|
||||
Identify=CompDir,Choosing=0
|
||||
Identify=CompSign,Choosing=0
|
||||
Identify=CompAbs,Choosing=0
|
||||
Identify=CompTI,Choosing=0
|
||||
Identify=MachUnit,"TextUnit=1 um"
|
||||
Identify=CompSel,Choosing=0
|
||||
Identify=CompStart,"TextUnit=1 mm"
|
||||
Identify=CompIntvl,"TextUnit=9.88888889 mm"
|
||||
Identify=CompEnd,"TextUnit=86 mm"
|
||||
Identify=UpperSel,Choosing=0
|
||||
Identify=LaserRes,"TextUnit=-1 um"
|
||||
Identify=LaserSen,Choosing=1
|
||||
Identify=ErrorRes,"TextUnit=-0.1 um"
|
||||
Identify=ComboRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=SpeedRes,"TextUnit=-0.01 mm/s"
|
||||
Identify=LaserRes2,"TextUnit=-0.01 um"
|
||||
Identify=LaserSen2,Choosing=1
|
||||
Identify=LowerSel,Choosing=3
|
||||
Identify=TargetRes,"TextUnit=-10 um"
|
||||
Identify=EncoderRes,"TextUnit=-0.01 um"
|
||||
Identify=RotaryRes,"TextUnit=-0.0001 arcdeg"
|
||||
Identify=RotarySen,Choosing=1
|
||||
Identify=MidDispSel,Choosing=0
|
||||
Identify=GraPanel,"ItemText=Straightness - Measurement Axis: Z"
|
||||
Identify=LimitSel,Choosing=0
|
||||
Identify=LimitLine,"TextUnit=25 um"
|
||||
Identify=UserSel,Choosing=0
|
||||
Identify=UserScale,"TextUnit=100 um"
|
||||
Identify=Legend,Choosing=1
|
||||
Identify=TarInRow,Choosing=1
|
||||
Identify=ResAxisSel,Choosing=0
|
||||
Identify=GridLines,Choosing=1
|
||||
Identify=Centered,Choosing=1
|
||||
Identify=FlaGraSel,Choosing=1
|
||||
Identify=ErrorSign,Choosing=0
|
||||
Identify=FirstRow,ItemText=1
|
||||
Identify=RefDisp,Choosing=2
|
||||
Identify=RotThita,"TextUnit=30 arcdeg"
|
||||
Identify=RotPhy,"TextUnit=15 arcdeg"
|
||||
Identify=FigRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvRanges,"ItemText=,,,",Expanded=N
|
||||
Identify=EnvUser,Choosing=0
|
||||
Identify=DataGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=CompGrids,"ItemText=0,0,0,0",Expanded=N
|
||||
Identify=LinearErr,"TextUnit=0.2309,1.1066,1.1236,0.7065,0.7424,0.6015,0.6407,-0.0070,-0.0791,0.2495,0.0853,0.2843,0.0807,0.4149,0.3897,0.4959,0.9113,0.4671,0.4640,0.7678,0.4946,0.7891,0.2065,0.4478,0.5273,0.2084,0.4906,-0.2051,0.3843,0.2670,0.6710,1.1268,1.2638,0.0794,1.1442,0.5069,0.9500,0.7563,1.0693,0.9062,0.7473,0.4261,0.2065,0.4298,0.3427,0.6618,0.5267,0.6362,0.7141,0.9321,0.7070,1.1220,0.6669,0.8263,0.6669,1.0608,0.2538,1.0818,0.7784,0.4537,0.7349,0.8669,0.4538,0.2444,0.1273,-0.2647,0.5686,0.4898,0.6199,1.3150,1.1688,0.3818,0.3028,-0.8318,1.2917,1.0161,0.0774,1.0368,1.1644,-0.0687,-0.1394,0.6983,0.6052,0.8832,0.7100,1.0659,1.0543,1.1443,1.0485,1.2004,1.3057,1.2536,1.4207,1.3571,-1.0266,0.5507,0.6986,0.6371,0.0803,0.4896,-0.1995,0.7373,1.2137,-0.3587,1.1977,0.2063,1.3496,0.5114,-0.4726,1.2701,2.7404,1.6817,1.6456,1.1986,0.1868,1.0004,0.5065,0.9420,0.7348,0.8311,-0.7930,0.6150,1.0714,1.2067,1.2425,1.2730,1.1968,1.4592,1.5688,1.5077,1.0881,0.9313,0.9990,0.5684,1.0551,-0.1024,0.2996,1.1416,1.3296,1.7691,0.8712,1.6156,0.4654,0.9865,2.1242,0.8445,1.2889,1.8472,0.5855,1.5743,1.0457,0.8600,1.3186,0.9223,1.1026,0.9134,1.1266,0.6134,1.2899,1.5382,1.2653,1.6661,1.9044,1.7415,1.7231,1.3423,1.4657,1.2603,1.1224,1.1943,0.9025,0.3183,1.0032,-0.2353,1.1062,2.4430,1.9017,1.7712,1.1830,0.9947 um",Expanded=N
|
||||
Identify=EnvDispSel,Choosing=0
|
||||
Identify=ATHistory,"TextUnit=22.45,22.45,22.45,22.45,22.45,22.45,22.45,22.45,22.45,22.45,22.45,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.46,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.47,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.48,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.49,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.50,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.51,22.52,22.52,22.52 C",Expanded=N
|
||||
Identify=APHistory,"TextUnit=730.7,730.6,730.6,730.6,730.6,730.6,730.6,730.6,730.6,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.6,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.5,730.4,730.5,730.5,730.5,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.4,730.3,730.4,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.3,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.2,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.2,730.2,730.1,730.2,730.1,730.2,730.1,730.1,730.2,730.2,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.2,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.1,730.0 mmHg",Expanded=N
|
||||
Identify=RHHistory,"TextUnit=55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55,55 %",Expanded=N
|
||||
Identify=MTHistory,"TextUnit=22.51,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.52,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.53,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.54,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.55,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.56,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.57,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58,22.58 C",Expanded=N
|
||||
Identify=ProgHist,"ItemText=0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92,93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112,113,114,115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,133,134,135,136,137,138,139,140,141,142,143,144,145,146,147,148,149,150,151,152,153,154,155,156,157,158,159,160,161,162,163,164,165,166,167,168,169,170,171,172,173,174,175,176,177,178,179,180",Expanded=N
|
||||
Identify=TimeHist,"ItemText=0,1,16,26,35,45,54,64,73,83,92,102,112,121,130,140,149,159,168,173,191,200,210,219,229,238,248,257,267,276,286,295,305,314,324,333,343,347,366,375,385,394,404,413,423,432,442,451,461,470,480,489,499,508,518,522,541,551,560,569,579,588,598,607,617,626,636,645,655,665,674,683,693,697,716,726,735,744,754,763,773,782,792,801,811,820,830,839,849,858,868,872,891,900,910,919,929,938,948,957,967,976,986,995,1005,1014,1024,1033,1043,1047,1066,1075,1085,1094,1104,1113,1123,1132,1142,1151,1161,1170,1180,1189,1199,1208,1218,1222,1241,1250,1260,1269,1279,1288,1298,1307,1317,1326,1336,1345,1355,1364,1374,1383,1393,1397,1416,1425,1435,1444,1454,1463,1473,1482,1490,1499,1509,1518,1528,1537,1547,1556,1566,1570,1588,1595,1605,1614,1624,1633,1643,1652,1662,1671,1681,1690,1700,1709,1719,1728,1738",Expanded=N
|
||||
Identify=NormRange,Choosing=1
|
||||
Identify=ATList,"TextUnit=22.45,,22.52,22.45,22.48,22.52 C",Expanded=N
|
||||
Identify=APList,"TextUnit=730.6,,730.7,730.0,730.4,730.0 mmHg",Expanded=N
|
||||
Identify=RHList,"TextUnit=55,,55,55,55,55 %",Expanded=N
|
||||
Identify=MT1List,"TextUnit=22.65,,22.72,22.65,22.68,22.72 C",Expanded=N
|
||||
Identify=MT2List,"TextUnit=22.37,,22.44,22.37,22.41,22.44 C",Expanded=N
|
||||
Identify=MT3List,"TextUnit=,,,,, C",Expanded=N
|
||||
Identify=EnvCount,ItemText=1879
|
||||
|
||||
<End of Option Description File - Rev. 1.00a>
|
||||
|
After Width: | Height: | Size: 3.3 MiB |
|
After Width: | Height: | Size: 3.5 MiB |
|
After Width: | Height: | Size: 3.7 MiB |
|
After Width: | Height: | Size: 3.4 MiB |
|
After Width: | Height: | Size: 3.1 MiB |
|
After Width: | Height: | Size: 3.4 MiB |
|
After Width: | Height: | Size: 3.4 MiB |
|
After Width: | Height: | Size: 3.5 MiB |
|
After Width: | Height: | Size: 1.9 MiB |
|
After Width: | Height: | Size: 3.3 MiB |
|
After Width: | Height: | Size: 2.5 MiB |
|
After Width: | Height: | Size: 3.7 MiB |
|
After Width: | Height: | Size: 3.2 MiB |
|
After Width: | Height: | Size: 3.5 MiB |
|
After Width: | Height: | Size: 3.2 MiB |
|
After Width: | Height: | Size: 3.6 MiB |
|
After Width: | Height: | Size: 3.6 MiB |
|
After Width: | Height: | Size: 3.4 MiB |
@@ -30,6 +30,12 @@ It does not use LaTeX, MiKTeX, or a `.tex` source file.
|
||||
only motor manufacturer/model/type/step count/resistance; Measurements
|
||||
supplies only characterization metrics and environmental min/mean/max
|
||||
values. `Measurements/Temperature` is additional temperature data only.
|
||||
- For Motor data, inspect `../Motor/Motor.xlsx` first when it exists. Use its
|
||||
explicitly identified motor record for manufacturer, model, motor type,
|
||||
step count, and resistance. Only when a requested field is absent or blank
|
||||
there, continue with other documents in `../Motor/`; preserve the exact
|
||||
source path for every populated field. Do not use Encoder-folder motor
|
||||
fields as a substitute for missing Motor-folder evidence.
|
||||
- The agent's work ends after updating `Agent_Report_Data.json` (and only the
|
||||
manifest when changing the approved input contract). The agent must
|
||||
not run the batch launcher, build a PDF, inspect or validate a PDF, or claim
|
||||
|
||||
@@ -1,46 +1,56 @@
|
||||
{
|
||||
"schema_version": 1,
|
||||
"ecmc": {
|
||||
"field_sources": {"positioning_speed": [], "positioning_acceleration": [], "positioning_measured_positions": [], "positioning_pid_settings": [], "straightness_speed": [], "straightness_acceleration": [], "straightness_measured_positions": [], "straightness_pid_settings": []},
|
||||
"positioning_speed": "",
|
||||
"positioning_acceleration": "",
|
||||
"positioning_measured_positions": "",
|
||||
"positioning_pid_settings": "",
|
||||
"straightness_speed": "",
|
||||
"straightness_acceleration": "",
|
||||
"straightness_measured_positions": "",
|
||||
"straightness_pid_settings": ""
|
||||
"field_sources": {"travel": ["ECMC/ED7062_CSP/cfg/axis.yaml"], "positioning_speed": ["ECMC/ED7062_CSP/cfg/stopBeforePosition.plc"], "positioning_acceleration": ["ECMC/ED7062_CSP/cfg/stopBeforePosition.plc"], "positioning_measured_positions": ["ECMC/ED7062_CSP/cfg/stopBeforePosition.plc"], "positioning_pid_settings": ["ECMC/ED7062_CSP/cfg/axis.yaml"], "straightness_speed": ["ECMC/ED7062_CSP/cfg/straightnessTest.plc"], "straightness_acceleration": ["ECMC/ED7062_CSP/cfg/straightnessTest.plc"], "straightness_measured_positions": ["ECMC/ED7062_CSP/cfg/straightnessTest.plc"], "straightness_pid_settings": ["ECMC/ED7062_CSP/cfg/axis.yaml"]},
|
||||
"travel": "96 mm (soft-limit span: 95 mm − (−1 mm))",
|
||||
"positioning_speed": "2 mm/s (configured VEL)",
|
||||
"positioning_acceleration": "3 mm/s²; deceleration 3 mm/s² (configured ACC and DEC)",
|
||||
"positioning_measured_positions": "10 positions from 1.0000 mm to 90.0000 mm; each measurement position is approached from a 0.2000 mm-lower intermediate position.",
|
||||
"positioning_pid_settings": "Configured controller: Kp = 0.06; Ki = 0.04; Kd = 0.01; Kff = 1.",
|
||||
"straightness_speed": "3 mm/s (configured VEL)",
|
||||
"straightness_acceleration": "2 mm/s²; deceleration 2 mm/s² (configured ACC and DEC)",
|
||||
"straightness_measured_positions": "20 positions: 1.0000 mm duplicated at indices 0–1; 6.0000 mm through 86.0000 mm in 5.0000 mm increments; 86.0000 mm duplicated at indices 18–19.",
|
||||
"straightness_pid_settings": "Configured controller: Kp = 0.06; Ki = 0.04; Kd = 0.01; Kff = 1."
|
||||
},
|
||||
"encoder": {
|
||||
"field_sources": {"manufacturer": [], "model": [], "communication_protocol": [], "resolution": [], "number_of_bits": []},
|
||||
"manufacturer": "",
|
||||
"model": "",
|
||||
"communication_protocol": "",
|
||||
"resolution": "",
|
||||
"number_of_bits": ""
|
||||
"field_sources": {"manufacturer": ["Encoder/OWIS_TR-ENCODER.xlsx"], "model": ["Encoder/OWIS_TR-ENCODER.xlsx"], "communication_protocol": ["Encoder/OWIS_TR-ENCODER.xlsx"], "resolution": ["Encoder/OWIS_TR-ENCODER.xlsx"], "number_of_bits": ["Encoder/OWIS_TR-ENCODER.xlsx"]},
|
||||
"manufacturer": "TR-Electronic GmbH",
|
||||
"model": "LT140-S",
|
||||
"communication_protocol": "SSI/24-bit binary",
|
||||
"resolution": "0.1 µm",
|
||||
"number_of_bits": "24 bits"
|
||||
},
|
||||
"motor": {
|
||||
"field_sources": {"manufacturer": [], "model": [], "motor_type": [], "step_count": [], "resistance": []},
|
||||
"manufacturer": "",
|
||||
"model": "",
|
||||
"motor_type": "",
|
||||
"step_count": "",
|
||||
"resistance": ""
|
||||
"field_sources": {"manufacturer": ["Motor/HM-7471E.pdf"], "model": ["Motor/Motor.xlsx"], "motor_type": ["Motor/HM-7471E.pdf"], "step_count": ["Motor/Motor.xlsx"], "resistance": ["Motor/Motor.xlsx"]},
|
||||
"manufacturer": "Oriental Motor Co., Ltd.",
|
||||
"model": "PK245M-02B-C2",
|
||||
"motor_type": "2-phase/5-phase stepping motor",
|
||||
"step_count": "400 steps/rev",
|
||||
"resistance": "7.5 Ω"
|
||||
},
|
||||
"drive": {
|
||||
"field_sources": {"model": ["ECMC/README.md"]},
|
||||
"model": "ED7062 CSP; ED7062 CSV; EL7041"
|
||||
},
|
||||
"test_dates": {
|
||||
"field_sources": {"dates": ["Measurements/OWIS_stageTR_Electronics_FAT_ISO230_Stepper_ED7062_CSP_EL5042_DC_ClosedLoop_SCurve_gap.pdf", "Measurements/OWIS_stageTR_Electronics_FAT_ISO230_Stepper_ED7062_CSV_EL5042_DC_ClosedLoop_SCurve_gap.pdf", "Measurements/OWIS_stageTR_Electronics_FAT_ISO230_Stepper_EL7041_EL5042.pdf", "Measurements/OWIS_stageTR_Electronics_FAT_Straightness_Horizontal_XZ.pdf", "Measurements/OWIS_stageTR_Electronics_FAT_Straightness_Vertical_YZ.pdf"]},
|
||||
"dates": "2026-08-27; 2026-09-07; 2026-09-08"
|
||||
},
|
||||
"measurement_system": {
|
||||
"field_sources": {"manufacturer": ["Measurement_System/5530 Laser Calibration System Components.pdf"], "system_model": ["Measurement_System/5530 Laser Calibration System Components.pdf"], "laser_head_model": ["Measurement_System/5530 Laser Calibration System Components.pdf"], "laser_type": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "vacuum_wavelength": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "wavelength_accuracy": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "wavelength_stability": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "linear_measurement_range": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "straightness_range_resolution": ["Measurement_System/5530 Laser Calibration System Components.pdf", "Measurement_System/5530 Dynamic Calibrator.pdf"], "environmental_compensation": ["Measurement_System/5530 Dynamic Calibrator.pdf"], "air_sensor_accuracy": ["Measurement_System/5530 Dynamic Calibrator.pdf"]},
|
||||
"manufacturer": "Keysight Technologies",
|
||||
"system_model": "5530 Laser Calibration System (datasheet family; installed configuration not established)",
|
||||
"laser_head_model": "5519A/B HeNe laser system (compatible component; installed variant not established)",
|
||||
"laser_type": "Helium-neon, automatically tuned Zeeman-split two-frequency output",
|
||||
"vacuum_wavelength": "632.991354 nm",
|
||||
"wavelength_accuracy": "±0.1 ppm; ±0.02 ppm only with stated factory-calibration option",
|
||||
"wavelength_stability": "±0.002 ppm short term (1 h); ±0.02 ppm lifetime",
|
||||
"linear_measurement_range": "Up to 40 m with linear optics; up to 80 m with long-range option",
|
||||
"straightness_range_resolution": "10774A short range: up to 3 m, 0.01 µm; 10775A long range: up to 30 m, 0.1 µm (selected optics not established)",
|
||||
"environmental_compensation": "E1738A air sensor supports automatic temperature, pressure, humidity, and wavelength-in-air compensation (installation not established)",
|
||||
"air_sensor_accuracy": "Temperature ±0.1 °C; relative humidity ±5 %; absolute pressure ±80 Pa"
|
||||
},
|
||||
"measurements": {
|
||||
"field_sources": {"positioning_accuracy": [], "positioning_precision_repeatability": [], "positioning_reversal_error_backlash": [], "positioning_temperature_min_mean_max": [], "positioning_pressure_min_mean_max": [], "positioning_humidity_min_mean_max": [], "straightness_accuracy": [], "straightness_precision_repeatability": [], "straightness_reversal_error_backlash": [], "straightness_temperature_min_mean_max": [], "straightness_pressure_min_mean_max": [], "straightness_humidity_min_mean_max": [], "additional_temperature_data": []},
|
||||
"positioning_accuracy": "",
|
||||
"positioning_precision_repeatability": "",
|
||||
"positioning_reversal_error_backlash": "",
|
||||
"positioning_temperature_min_mean_max": "",
|
||||
"positioning_pressure_min_mean_max": "",
|
||||
"positioning_humidity_min_mean_max": "",
|
||||
"straightness_accuracy": "",
|
||||
"straightness_precision_repeatability": "",
|
||||
"straightness_reversal_error_backlash": "",
|
||||
"straightness_temperature_min_mean_max": "",
|
||||
"straightness_pressure_min_mean_max": "",
|
||||
"straightness_humidity_min_mean_max": "",
|
||||
"additional_temperature_data": ""
|
||||
"field_sources": {}
|
||||
}
|
||||
}
|
||||
@@ -10,6 +10,7 @@
|
||||
"ecmc": {
|
||||
"source_root": "ECMC",
|
||||
"fields": {
|
||||
"travel": "travel_range",
|
||||
"positioning_speed": "positioning_speed",
|
||||
"positioning_acceleration": "positioning_acceleration",
|
||||
"positioning_measured_positions": "positioning_travel_and_targets",
|
||||
@@ -20,6 +21,7 @@
|
||||
"straightness_pid_settings": "straightness_pid_settings"
|
||||
},
|
||||
"source_patterns": {
|
||||
"travel": ["ECMC/**/axis.yaml"],
|
||||
"positioning_speed": ["ECMC/**"],
|
||||
"positioning_acceleration": ["ECMC/**"],
|
||||
"positioning_measured_positions": ["ECMC/**/stopBeforePosition.plc"],
|
||||
@@ -53,29 +55,27 @@
|
||||
},
|
||||
"source_patterns": {"manufacturer": ["Motor/**"], "model": ["Motor/**"], "motor_type": ["Motor/**"], "step_count": ["Motor/**"], "resistance": ["Motor/**"]}
|
||||
},
|
||||
"drive": {
|
||||
"source_root": "ECMC",
|
||||
"fields": {"model": "drive_model"},
|
||||
"source_patterns": {"model": ["ECMC/**"]}
|
||||
},
|
||||
"test_dates": {
|
||||
"source_root": "Measurements",
|
||||
"fields": {"dates": "test_dates"},
|
||||
"source_patterns": {"dates": ["Measurements/*.pdf"]}
|
||||
},
|
||||
"measurement_system": {
|
||||
"source_root": "Measurement_System",
|
||||
"fields": {"manufacturer": "measurement_system_manufacturer", "system_model": "measurement_system_model", "laser_head_model": "laser_head_model", "laser_type": "laser_type", "vacuum_wavelength": "vacuum_wavelength", "wavelength_accuracy": "wavelength_accuracy", "wavelength_stability": "wavelength_stability", "linear_measurement_range": "linear_measurement_range", "straightness_range_resolution": "straightness_range_resolution", "environmental_compensation": "environmental_compensation", "air_sensor_accuracy": "air_sensor_accuracy"},
|
||||
"source_patterns": {"manufacturer": ["Measurement_System/*.pdf"], "system_model": ["Measurement_System/*.pdf"], "laser_head_model": ["Measurement_System/*.pdf"], "laser_type": ["Measurement_System/*.pdf"], "vacuum_wavelength": ["Measurement_System/*.pdf"], "wavelength_accuracy": ["Measurement_System/*.pdf"], "wavelength_stability": ["Measurement_System/*.pdf"], "linear_measurement_range": ["Measurement_System/*.pdf"], "straightness_range_resolution": ["Measurement_System/*.pdf"], "environmental_compensation": ["Measurement_System/*.pdf"], "air_sensor_accuracy": ["Measurement_System/*.pdf"]},
|
||||
"notes": "Datasheet values describe manufacturer capability. State whether the installed configuration, serial number, and calibration state are established."
|
||||
},
|
||||
"measurements": {
|
||||
"source_root": "Measurements",
|
||||
"fields": {
|
||||
"positioning_accuracy": "positioning_accuracy",
|
||||
"positioning_precision_repeatability": "positioning_precision_repeatability",
|
||||
"positioning_reversal_error_backlash": "positioning_reversal_error_backlash",
|
||||
"positioning_temperature_min_mean_max": "positioning_temperature",
|
||||
"positioning_pressure_min_mean_max": "positioning_pressure",
|
||||
"positioning_humidity_min_mean_max": "positioning_humidity",
|
||||
"straightness_accuracy": "straightness_accuracy",
|
||||
"straightness_precision_repeatability": "straightness_precision_repeatability",
|
||||
"straightness_reversal_error_backlash": "straightness_reversal_error_backlash",
|
||||
"straightness_temperature_min_mean_max": "straightness_temperature",
|
||||
"straightness_pressure_min_mean_max": "straightness_pressure",
|
||||
"straightness_humidity_min_mean_max": "straightness_humidity",
|
||||
"additional_temperature_data": "additional_temperature"
|
||||
},
|
||||
"source_patterns": {
|
||||
"positioning_accuracy": ["Measurements/**"], "positioning_precision_repeatability": ["Measurements/**"], "positioning_reversal_error_backlash": ["Measurements/**"], "positioning_temperature_min_mean_max": ["Measurements/**"], "positioning_pressure_min_mean_max": ["Measurements/**"], "positioning_humidity_min_mean_max": ["Measurements/**"],
|
||||
"straightness_accuracy": ["Measurements/**"], "straightness_precision_repeatability": ["Measurements/**"], "straightness_reversal_error_backlash": ["Measurements/**"], "straightness_temperature_min_mean_max": ["Measurements/**"], "straightness_pressure_min_mean_max": ["Measurements/**"], "straightness_humidity_min_mean_max": ["Measurements/**"],
|
||||
"additional_temperature_data": ["Measurements/Temperature/**"]
|
||||
},
|
||||
"notes": "Use Measurements/Temperature data only as additional temperature data; do not substitute it for per-test environmental records."
|
||||
"fields": {},
|
||||
"source_patterns": {},
|
||||
"notes": "The generator reads every top-level Measurements/*.pdf and creates one evidence-labelled test record per PDF. Measurement result and environmental fields are therefore not entered here. Measurements/Temperature remains supplementary evidence only."
|
||||
}
|
||||
}
|
||||
}
|
||||
@@ -41,9 +41,13 @@ from reportlab.platypus import (
|
||||
Spacer, Table, TableStyle,
|
||||
)
|
||||
|
||||
# Cover layout: increase or decrease this single value to change the width of
|
||||
# the right-hand Project / Document / Revision metadata column.
|
||||
COVER_RIGHT_COLUMN_WIDTH_MM = 65.0
|
||||
# Cover header layout: the left column automatically occupies the remaining
|
||||
# framed width. Adjust these two values to change the row height and the
|
||||
# right-hand Project / Document / Review column width.
|
||||
COVER_HEADER_ROW_HEIGHT_MM = 12.0
|
||||
COVER_RIGHT_COLUMN_WIDTH_MM = 80.0
|
||||
# Negative values lower the Document Identification filename in its cell.
|
||||
COVER_DOCUMENT_VALUE_VERTICAL_OFFSET_MM = -2.0
|
||||
|
||||
|
||||
# Fixed, evidence-bounded project values. Do not fill unknown values with
|
||||
@@ -67,6 +71,17 @@ REPORT_DATA = {
|
||||
"encoder_bits": "",
|
||||
"controller": "",
|
||||
"measurement_system": "",
|
||||
"measurement_system_manufacturer": "",
|
||||
"measurement_system_model": "",
|
||||
"laser_head_model": "",
|
||||
"laser_type": "",
|
||||
"vacuum_wavelength": "",
|
||||
"wavelength_accuracy": "",
|
||||
"wavelength_stability": "",
|
||||
"linear_measurement_range": "",
|
||||
"straightness_range_resolution": "",
|
||||
"environmental_compensation": "",
|
||||
"air_sensor_accuracy": "",
|
||||
"test_dates": "",
|
||||
"test_operator": "",
|
||||
"travel_range": "",
|
||||
@@ -132,7 +147,10 @@ CHECKLIST_SECTIONS = (
|
||||
class WorkbookInputs:
|
||||
report_type: str
|
||||
stage_identifier: str
|
||||
stage_name: str
|
||||
repository: str
|
||||
main_facility: str
|
||||
author: str
|
||||
coordinate_convention: dict[str, str]
|
||||
checklist_sections: tuple[tuple[str, tuple[tuple[str, str, str, str, str], ...]], ...]
|
||||
|
||||
@@ -170,7 +188,7 @@ def read_workbook(workbook_path: Path) -> WorkbookInputs:
|
||||
raise ValueError(f"This generator supports Characterization only; workbook Report type is {report_type!r}.")
|
||||
convention = {
|
||||
text_or_blank(read_me.cell(row, 2).value): text_or_blank(read_me.cell(row, 4).value) or text_or_blank(read_me.cell(row, 3).value)
|
||||
for row in range(11, 17)
|
||||
for row in range(14, 20)
|
||||
}
|
||||
|
||||
parsed_sections: list[tuple[str, tuple[tuple[str, str, str, str, str], ...]]] = []
|
||||
@@ -204,7 +222,10 @@ def read_workbook(workbook_path: Path) -> WorkbookInputs:
|
||||
return WorkbookInputs(
|
||||
report_type=report_type,
|
||||
stage_identifier=text_or_blank(read_me["C7"].value),
|
||||
repository=valid_repository_url(text_or_blank(read_me["C8"].value)),
|
||||
stage_name=text_or_blank(read_me["C8"].value),
|
||||
repository=valid_repository_url(text_or_blank(read_me["C9"].value)),
|
||||
main_facility=text_or_blank(read_me["C10"].value),
|
||||
author=text_or_blank(read_me["C11"].value),
|
||||
coordinate_convention=convention,
|
||||
checklist_sections=tuple(parsed_sections),
|
||||
)
|
||||
@@ -262,7 +283,9 @@ def read_agent_data(data_path: Path, manifest_path: Path) -> dict[str, str]:
|
||||
if unexpected:
|
||||
raise ValueError("Agent report data contains unmanifested domain(s): " + ", ".join(sorted(unexpected)))
|
||||
|
||||
repo_root = data_path.resolve().parent.parent
|
||||
# Agent data resides in Report/python_script; resolve evidence paths from
|
||||
# the repository root rather than from the Report directory.
|
||||
repo_root = data_path.resolve().parent.parent.parent
|
||||
flattened: dict[str, str] = {}
|
||||
for domain, definition in domains.items():
|
||||
if not isinstance(definition, dict):
|
||||
@@ -322,19 +345,26 @@ def read_agent_data(data_path: Path, manifest_path: Path) -> dict[str, str]:
|
||||
class EvidenceImage(Flowable):
|
||||
"""Use a supplied raster image or draw a visible, non-substituting placeholder."""
|
||||
|
||||
def __init__(self, media_dir: Path, basename: str, width: float, height: float):
|
||||
def __init__(self, media_dir: Path, basename: str, width: float, height: float, preserve_aspect: bool = False):
|
||||
super().__init__()
|
||||
self.width, self.height = width, height
|
||||
self.basename = basename
|
||||
self.preserve_aspect = preserve_aspect
|
||||
self.path = next((media_dir / f"{basename}{suffix}" for suffix in (".jpg", ".jpeg", ".png") if (media_dir / f"{basename}{suffix}").exists()), None)
|
||||
if self.path and self.preserve_aspect:
|
||||
fitted = Image(str(self.path), width=width, height=height, kind="proportional")
|
||||
self.width, self.height = fitted.drawWidth, fitted.drawHeight
|
||||
|
||||
def draw(self) -> None:
|
||||
canvas = self.canv
|
||||
canvas.setStrokeColor(colors.black)
|
||||
canvas.rect(0, 0, self.width, self.height)
|
||||
if self.path:
|
||||
image = Image(str(self.path), width=self.width, height=self.height, kind="proportional")
|
||||
image.drawOn(canvas, 0, 0)
|
||||
if self.preserve_aspect:
|
||||
image = Image(str(self.path), width=self.width, height=self.height, kind="proportional")
|
||||
image.drawOn(canvas, 0, 0)
|
||||
else:
|
||||
canvas.drawImage(str(self.path), 0, 0, width=self.width, height=self.height, preserveAspectRatio=False, mask="auto")
|
||||
else:
|
||||
canvas.setFont("Helvetica", 6)
|
||||
canvas.drawCentredString(self.width / 2, self.height / 2 + 4, "Required image not found")
|
||||
@@ -410,18 +440,39 @@ def cover(canvas, document) -> None:
|
||||
logo = Path(__file__).resolve().parent / "PSI_Logo.png"
|
||||
if logo.exists():
|
||||
canvas.drawImage(str(logo), margin + 5 * mm, A4[1] - 29 * mm, width=30 * mm, height=10 * mm, preserveAspectRatio=True, mask="auto")
|
||||
right_edge, top = A4[0] - margin - 5 * mm, A4[1] - 22 * mm
|
||||
header_top = A4[1] - margin
|
||||
row_height = COVER_HEADER_ROW_HEIGHT_MM * mm
|
||||
header_bottom = header_top - 3 * row_height
|
||||
right_edge = A4[0] - margin
|
||||
right_column_width = COVER_RIGHT_COLUMN_WIDTH_MM * mm
|
||||
canvas.setFont("Helvetica", 6.5)
|
||||
canvas.drawRightString(right_edge, top, "Project")
|
||||
project_lines = simpleSplit(value("project_name"), "Helvetica", 6.5, right_column_width) or [""]
|
||||
for index, line in enumerate(project_lines):
|
||||
canvas.drawRightString(right_edge, top - (4 + 3.5 * index) * mm, line)
|
||||
metadata_y = top - (5 + 3.5 * len(project_lines)) * mm
|
||||
canvas.drawRightString(right_edge, metadata_y, f"Document: {value('document_number')}")
|
||||
canvas.drawRightString(right_edge, metadata_y - 4 * mm, f"Revision: {value('report_version')}")
|
||||
canvas.setFont("Helvetica-Bold", 12)
|
||||
canvas.drawString(margin + 5 * mm, A4[1] - 53 * mm, "Linear Stage Characterization Report")
|
||||
right_column_left = right_edge - right_column_width
|
||||
left_column_center = (margin + right_column_left) / 2
|
||||
right_column_center = right_column_left + right_column_width / 2
|
||||
|
||||
def draw_cell_value(text: str, center_x: float, row_top: float, cell_width: float, font_name: str = "Helvetica", font_size: float = 9, vertical_offset: float = 0) -> None:
|
||||
"""Centre a wrapped data value within a labelled cover-header cell."""
|
||||
lines = simpleSplit(text, font_name, font_size, cell_width - 6 * mm) or [""]
|
||||
leading = (font_size + 2) * mm / 2.85
|
||||
center_y = row_top - row_height / 2 + vertical_offset
|
||||
canvas.setFont(font_name, font_size)
|
||||
for index, line in enumerate(lines):
|
||||
canvas.drawCentredString(center_x, center_y + ((len(lines) - 1) / 2 - index) * leading, line)
|
||||
canvas.line(right_column_left, header_bottom, right_column_left, header_top)
|
||||
canvas.line(margin, header_top - row_height, right_edge, header_top - row_height)
|
||||
canvas.line(margin, header_top - 2 * row_height, right_edge, header_top - 2 * row_height)
|
||||
canvas.line(margin, header_bottom, right_edge, header_bottom)
|
||||
canvas.setFont("Helvetica", 8)
|
||||
canvas.drawString(right_column_left + 2 * mm, header_top - 4 * mm, "Project")
|
||||
draw_cell_value(value("project_name"), right_column_center, header_top, right_column_width, "Helvetica-Bold", 10)
|
||||
canvas.setFont("Helvetica", 8)
|
||||
canvas.drawString(margin + 2 * mm, header_top - row_height - 4 * mm, "Title")
|
||||
canvas.drawString(right_column_left + 2 * mm, header_top - row_height - 3 * mm, "Document Identification")
|
||||
canvas.drawString(margin + 2 * mm, header_top - 2 * row_height - 4 * mm, "Author")
|
||||
canvas.drawString(right_column_left + 2 * mm, header_top - 2 * row_height - 4 * mm, "Review Index")
|
||||
draw_cell_value("Linear Stage Characterization Report", left_column_center, header_top - row_height, right_column_left - margin, "Helvetica-Bold", 10)
|
||||
draw_cell_value(value("document_number"), right_column_center, header_top - row_height, right_column_width, vertical_offset=COVER_DOCUMENT_VALUE_VERTICAL_OFFSET_MM * mm)
|
||||
draw_cell_value(value("test_operator"), left_column_center, header_top - 2 * row_height, right_column_left - margin)
|
||||
draw_cell_value(value("report_version"), right_column_center, header_top - 2 * row_height, right_column_width, "Helvetica-Bold", 9)
|
||||
canvas.restoreState()
|
||||
|
||||
|
||||
@@ -436,8 +487,10 @@ def build_story(report_dir: Path, workbook_inputs: WorkbookInputs) -> tuple[list
|
||||
tests = measurement_records(pdfs)
|
||||
story: list[object] = []
|
||||
|
||||
story += [Spacer(1, 43 * mm), Paragraph("Overall stage image", subheading), EvidenceImage(media_dir, "I1", 130 * mm, 75 * mm), Spacer(1, 5 * mm)]
|
||||
cover_rows = [["Test type", workbook_inputs.report_type], ["Stage identifier", value("stage_identifier")], ["Repository", value("repository")], ["Encoder", value("encoder_model")], ["Motor", value("motor_model")], ["Drive", value("drive_model")], ["Dates", value("test_dates")], ["Applicable standards", value("applicable_standards")]]
|
||||
i1_frame = Table([[EvidenceImage(media_dir, "I1", 160 * mm, 75 * mm, preserve_aspect=True)]], colWidths=[160 * mm], hAlign="CENTER")
|
||||
i1_frame.setStyle(TableStyle([("ALIGN", (0, 0), (-1, -1), "CENTER"), ("LEFTPADDING", (0, 0), (-1, -1), 0), ("RIGHTPADDING", (0, 0), (-1, -1), 0), ("TOPPADDING", (0, 0), (-1, -1), 0), ("BOTTOMPADDING", (0, 0), (-1, -1), 0)]))
|
||||
story += [Spacer(1, (3 * COVER_HEADER_ROW_HEIGHT_MM + 3) * mm), Paragraph("Overall stage image", subheading), i1_frame, Spacer(1, 5 * mm)]
|
||||
cover_rows = [["Test type", workbook_inputs.report_type], ["Stage identifier", value("stage_identifier")], ["Main Facility", workbook_inputs.main_facility], ["Repository", value("repository")], ["Encoder", "; ".join(part for part in (value("encoder_manufacturer"), value("encoder_model")) if part)], ["Motor", "; ".join(part for part in (value("motor_type"), value("motor_manufacturer"), value("motor_model")) if part)], ["Drive", value("drive_model")], ["Dates", value("test_dates")], ["Applicable standards", value("applicable_standards")]]
|
||||
story += [grid(cover_rows, [45 * mm, 115 * mm], header=False), PageBreak(), Paragraph("Test Checklists", heading)]
|
||||
for section, entries in workbook_inputs.checklist_sections:
|
||||
rows = [["Item", "Checklist Item", "Yes", "No", "Remarks"]]
|
||||
@@ -447,8 +500,10 @@ def build_story(report_dir: Path, workbook_inputs: WorkbookInputs) -> tuple[list
|
||||
story += [PageBreak(), Paragraph("Hardware and Configuration", heading), Paragraph("Coordinate Convention", subheading)]
|
||||
coordinates = [["Quantity", "Project convention"]] + [[label, convention] for label, convention in workbook_inputs.coordinate_convention.items()] + [["Positive rotational direction", "Right-hand rule"]]
|
||||
story += [grid(coordinates, [45 * mm, 115 * mm]), Spacer(1, 6 * mm)]
|
||||
hardware = [["Component", "Verified specification"], ["Stage", value("stage_model")], ["Stage identifier", value("stage_identifier")], ["Travel", value("travel_range")], ["Encoder", "; ".join(part for part in (value("encoder_manufacturer"), value("encoder_model")) if part)], ["Encoder protocol", value("encoder_interface")], ["Encoder resolution", "; ".join(part for part in (value("encoder_resolution"), value("encoder_bits")) if part)], ["Motor or actuator", "; ".join(part for part in (value("motor_manufacturer"), value("motor_model")) if part)], ["Motor type and steps", "; ".join(part for part in (value("motor_type"), value("motor_step_count")) if part)], ["Motor resistance", value("motor_resistance")], ["Drive", value("drive_model")], ["Controller and control mode", value("controller")], ["Measurement system", value("measurement_system")]]
|
||||
hardware = [["Component", "Verified specification"], ["Stage", workbook_inputs.stage_name], ["Stage identifier", value("stage_identifier")], ["Travel", value("travel_range")], ["Encoder", "; ".join(part for part in (value("encoder_manufacturer"), value("encoder_model")) if part)], ["Encoder protocol", value("encoder_interface")], ["Encoder resolution", value("encoder_resolution")], ["Motor or actuator", "; ".join(part for part in (value("motor_manufacturer"), value("motor_model")) if part)], ["Motor type and steps", "; ".join(part for part in (value("motor_type"), value("motor_step_count")) if part)], ["Motor resistance", value("motor_resistance")], ["Drive", value("drive_model")], ["Controller and control mode", value("controller")]]
|
||||
story += [grid(hardware, [45 * mm, 115 * mm]), Spacer(1, 7 * mm)]
|
||||
measurement_system = [["Measurement-system parameter", "Documented value"], ["Manufacturer", value("measurement_system_manufacturer")], ["System family / model", value("measurement_system_model")], ["Laser-head model", value("laser_head_model")], ["Laser type", value("laser_type")], ["Vacuum wavelength", value("vacuum_wavelength")], ["Wavelength accuracy", value("wavelength_accuracy")], ["Wavelength stability", value("wavelength_stability")], ["Linear measurement range", value("linear_measurement_range")], ["Straightness range / resolution", value("straightness_range_resolution")], ["Environmental compensation", value("environmental_compensation")], ["Air-sensor accuracy", value("air_sensor_accuracy")]]
|
||||
story += [Paragraph("Measurement System", subheading), grid(measurement_system, [55 * mm, 105 * mm]), Spacer(1, 7 * mm)]
|
||||
story += [PageBreak(), Paragraph("Evidence Images", heading)]
|
||||
story += [Table([[EvidenceImage(media_dir, "I2", 50 * mm, 58 * mm), EvidenceImage(media_dir, "I3", 50 * mm, 58 * mm), EvidenceImage(media_dir, "I4", 50 * mm, 58 * mm)], [p("Encoder", small), p("Motor", small), p("Coupling", small)]], colWidths=[53 * mm, 53 * mm, 53 * mm]), Spacer(1, 5 * mm), Table([[EvidenceImage(media_dir, "I5", 78 * mm, 82 * mm), EvidenceImage(media_dir, "I6", 78 * mm, 82 * mm)], [p("Measurement setup", small), p("Measurement setup 2", small)]], colWidths=[80 * mm, 80 * mm])]
|
||||
|
||||
@@ -506,6 +561,7 @@ def main() -> int:
|
||||
REPORT_DATA["document_number"] = output.name
|
||||
REPORT_DATA["stage_identifier"] = workbook_inputs.stage_identifier
|
||||
REPORT_DATA["repository"] = workbook_inputs.repository
|
||||
REPORT_DATA["test_operator"] = workbook_inputs.author
|
||||
output.parent.mkdir(parents=True, exist_ok=True)
|
||||
temporary = output.with_suffix(".base.pdf")
|
||||
document = SimpleDocTemplate(str(temporary), pagesize=A4, leftMargin=21 * mm, rightMargin=21 * mm, topMargin=24 * mm, bottomMargin=20 * mm, title="Linear Stage Characterization Report")
|
||||
|
||||
@@ -0,0 +1,190 @@
|
||||
<mxfile host="Electron" agent="Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) draw.io/29.0.3 Chrome/140.0.7339.249 Electron/38.7.0 Safari/537.36" version="29.0.3">
|
||||
<diagram name="Report Workflow" id="OWy0dci5RTJpJNXqNlxN">
|
||||
<mxGraphModel dx="2824" dy="1894" grid="0" gridSize="10" guides="1" tooltips="1" connect="1" arrows="1" fold="1" page="1" pageScale="1" pageWidth="2336" pageHeight="1654" math="0" shadow="0">
|
||||
<root>
|
||||
<mxCell id="0" />
|
||||
<mxCell id="1" parent="0" />
|
||||
<mxCell id="title" value="Linear-stage report workflow — evidence-bounded FAT or characterization" style="text;html=1;align=center;verticalAlign=middle;fontSize=22;fontStyle=1;fontColor=#1A1A1A;" parent="1" vertex="1">
|
||||
<mxGeometry x="230" y="20" width="1660" height="40" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="start" value="Start: create a project repository from the FAT_Template" style="ellipse;whiteSpace=wrap;html=1;fillColor=#d5e8d4;strokeColor=#82b366;fontSize=14;" parent="1" vertex="1">
|
||||
<mxGeometry x="60" y="294" width="210" height="70" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="collect" value="Collect and preserve source evidence<br>• measurements / raw data<br>• hardware and configuration evidence<br>• six mapped images I1–I6<br>• acceptance criteria (FAT only)" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#dae8fc;strokeColor=#6c8ebf;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="327" y="274" width="300" height="110" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="workbook" value="Complete FAT_Checklist.xlsx during the test<br>• Report Type<br>• stage ID and repository URL<br>• coordinate convention<br>• explicit Yes/No and remarks" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#dae8fc;strokeColor=#6c8ebf;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="658" y="274" width="300" height="110" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="selector" value="Is the workbook Report Type<br>unambiguous and consistent?" style="rhombus;whiteSpace=wrap;html=1;fillColor=#fff2cc;strokeColor=#d6b656;fontSize=14;fontStyle=1;" parent="1" vertex="1">
|
||||
<mxGeometry x="994" y="269" width="190" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="resolve" value="Resolve with the user<br>Do not construct the report" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#f8cecc;strokeColor=#b85450;fontSize=14;" parent="1" vertex="1">
|
||||
<mxGeometry x="996" y="459" width="190" height="70" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="template" value="Select the authoritative static template<br>FAT → FAT template<br>Characterization → characterization template" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#e1d5e7;strokeColor=#9673a6;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="1246" y="274" width="300" height="110" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="preflight" value="Evidence preflight<br>Read Report/AGENTS.md; inventory and hash inputs; inspect every image; confirm exact identities, dates, revisions, settings, calibration and PDF appendix set" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#dae8fc;strokeColor=#6c8ebf;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="1604" y="221.5" width="286" height="215" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="sufficient" value="Evidence sufficient<br>for a supported report?" style="rhombus;whiteSpace=wrap;html=1;fillColor=#fff2cc;strokeColor=#d6b656;fontSize=14;fontStyle=1;" parent="1" vertex="1">
|
||||
<mxGeometry x="1936" y="269" width="190" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="gaps" value="Record exact evidence gaps in workflow state<br>Prepare only an incomplete working draft; do not issue or infer values" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#f8cecc;strokeColor=#b85450;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="2092" y="394" width="202" height="175" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="populate" value="Create a new project-specific report<br>Populate marked data only; transfer workbook answers by stable item ID; retain blanks; list exact evidence filenames; preserve fixed template prose/layout" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#d5e8d4;strokeColor=#82b366;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="22" y="644" width="360" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="fat" value="FAT path<br>Trace criteria, results and uncertainty; compare only supported results; record deviations / owners / due dates; write evidence-backed conclusions" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#e1d5e7;strokeColor=#9673a6;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="482" y="639" width="310" height="130" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="char" value="Characterization path<br>State scope and positioning / straightness results only; no acceptance criteria, pass/fail disposition, uncertainty commentary, observations or conclusions" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#e1d5e7;strokeColor=#9673a6;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="482" y="809" width="310" height="130" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="build" value="Build and assemble<br>Compile with MiKTeX pdflatex twice; resolve errors/references; append every Measurements PDF as complete pages; retain workflow records under Report/unused/workflow" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#d5e8d4;strokeColor=#82b366;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="897" y="689" width="360" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="qa" value="Independent validation<br>1. Build/log check<br>2. Content/evidence check<br>3. Render and visually inspect every page<br>4. Verify appendices, logo, Repository URL, no placeholders or auxiliary files" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#dae8fc;strokeColor=#6c8ebf;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="1357" y="669" width="420" height="160" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="ready" value="All issued-report completion criteria met?" style="rhombus;whiteSpace=wrap;html=1;fillColor=#fff2cc;strokeColor=#d6b656;fontSize=14;fontStyle=1;" parent="1" vertex="1">
|
||||
<mxGeometry x="1847" y="689" width="170" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="correct" value="Correct source or evidence register<br>then rebuild and repeat all affected QA" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#f8cecc;strokeColor=#b85450;fontSize=14;" parent="1" vertex="1">
|
||||
<mxGeometry x="2008" y="834" width="300" height="75" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="review" value="Ready for issue review<br>Deliver project-specific .tex and .pdf; report page count, appended PDFs, validation status and residual unverified conditions" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#d5e8d4;strokeColor=#82b366;fontSize=14;align=left;spacingLeft=10;" parent="1" vertex="1">
|
||||
<mxGeometry x="437" y="1087" width="390" height="95" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="issue" value="User explicitly directs issuance?" style="rhombus;whiteSpace=wrap;html=1;fillColor=#fff2cc;strokeColor=#d6b656;fontSize=14;fontStyle=1;" parent="1" vertex="1">
|
||||
<mxGeometry x="977" y="1074" width="190" height="120" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="hold" value="Keep as review-ready<br>Technical QA is not FAT acceptance authorization" style="rounded=1;whiteSpace=wrap;html=1;fillColor=#f8cecc;strokeColor=#b85450;fontSize=14;" parent="1" vertex="1">
|
||||
<mxGeometry x="1284" y="1091" width="290" height="85" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="issued" value="Issue controlled report<br>Archive workflow state; do not claim acceptance without supported FAT disposition and authorization" style="ellipse;whiteSpace=wrap;html=1;fillColor=#d5e8d4;strokeColor=#82b366;fontSize=14;" parent="1" vertex="1">
|
||||
<mxGeometry x="922" y="1319" width="300" height="85" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e1" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="start" target="collect" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e2" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="collect" target="workbook" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e3" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="workbook" target="selector" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e4" value="No" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="selector" target="resolve" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e5" value="Yes" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="selector" target="template" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e6" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;entryX=0;entryY=0.5;entryDx=0;entryDy=0;" parent="1" source="template" target="preflight" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<mxPoint x="1613.999999999999" y="329.5" as="targetPoint" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e7" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;exitX=1;exitY=0.5;exitDx=0;exitDy=0;" parent="1" source="preflight" target="sufficient" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<mxPoint x="1900" y="329.5" as="sourcePoint" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e8" value="No" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;exitX=1;exitY=0.5;exitDx=0;exitDy=0;entryX=0.5;entryY=0;entryDx=0;entryDy=0;" parent="1" source="sufficient" target="gaps" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<mxPoint x="2148" y="326.47" as="sourcePoint" />
|
||||
<mxPoint x="2336" y="331.47" as="targetPoint" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e9" value="Yes" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;exitX=0.5;exitY=1;exitDx=0;exitDy=0;" parent="1" source="sufficient" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="2031" y="589" />
|
||||
<mxPoint x="180" y="589" />
|
||||
</Array>
|
||||
<mxPoint x="2120" y="439" as="sourcePoint" />
|
||||
<mxPoint x="180.0666666666666" y="644" as="targetPoint" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="wm-nTcyZt0jjmNqrfcTj-1" value="Yes" style="edgeLabel;html=1;align=center;verticalAlign=middle;resizable=0;points=[];fontStyle=1" vertex="1" connectable="0" parent="e9">
|
||||
<mxGeometry x="-0.9863" relative="1" as="geometry">
|
||||
<mxPoint as="offset" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e10" value="FAT" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="populate" target="fat" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e11" value="Characterization" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="populate" target="char" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="407" y="874" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e12" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="fat" target="build" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="847" y="704" />
|
||||
<mxPoint x="847" y="749" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e13" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="char" target="build" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="847" y="874" />
|
||||
<mxPoint x="847" y="749" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e14" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="build" target="qa" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e15" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="qa" target="ready" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e16" value="No" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;exitX=1;exitY=0.5;exitDx=0;exitDy=0;" parent="1" source="ready" target="correct" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e17" value="Yes" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="ready" target="review" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="1932" y="1039" />
|
||||
<mxPoint x="632" y="1039" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="wm-nTcyZt0jjmNqrfcTj-2" value="<b>Yes</b>" style="edgeLabel;html=1;align=center;verticalAlign=middle;resizable=0;points=[];" vertex="1" connectable="0" parent="e17">
|
||||
<mxGeometry x="-0.9713" y="1" relative="1" as="geometry">
|
||||
<mxPoint as="offset" />
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e18" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;dashed=1;" parent="1" source="correct" target="build" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="1607" y="979" />
|
||||
<mxPoint x="1607" y="869" />
|
||||
<mxPoint x="1077" y="869" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
<mxCell id="e19" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;" parent="1" source="review" target="issue" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e20" value="No" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;" parent="1" source="issue" target="hold" edge="1">
|
||||
<mxGeometry relative="1" as="geometry" />
|
||||
</mxCell>
|
||||
<mxCell id="e21" value="Yes" style="edgeStyle=orthogonalEdgeStyle;rounded=0;html=1;endArrow=block;endFill=1;fontStyle=1;exitX=0.5;exitY=1;exitDx=0;exitDy=0;" parent="1" source="issue" target="issued" edge="1">
|
||||
<mxGeometry relative="1" as="geometry">
|
||||
<Array as="points">
|
||||
<mxPoint x="1072" y="1329" />
|
||||
<mxPoint x="1072" y="1329" />
|
||||
</Array>
|
||||
</mxGeometry>
|
||||
</mxCell>
|
||||
</root>
|
||||
</mxGraphModel>
|
||||
</diagram>
|
||||
</mxfile>
|
||||