139 lines
5.3 KiB
Plaintext
139 lines
5.3 KiB
Plaintext
##############################################################################
|
||
## Example: Demo of ecmc grbl g-code plugin
|
||
## https://github.com/anderssandstrom/ecmc_plugin_grbl
|
||
## https://github.com/anderssandstrom/e3-ecmc_plugin_grbl
|
||
##
|
||
## The plugin exposes:
|
||
##
|
||
|
||
## Initiation:
|
||
|
||
require ecmccfg v9.0.1_RC1 "ECMC_VER=v9.0.1_RC1"
|
||
require ecmc_plugin_grbl sandst_a
|
||
|
||
exit
|
||
|
||
##############################################################################
|
||
## Configure hardware:
|
||
|
||
# Hardware for X and Y in ESS crate
|
||
$(SCRIPTEXEC) $(ecmccfg_DIR)ecmcMCU1021_coupler.cmd
|
||
|
||
## Use EL7211 as spindle
|
||
#epicsEnvSet("ECMC_EC_SLAVE_NUM", "11")
|
||
#epicsEnvSet("ECMC_EC_SLAVE_NUM_SPINDLE", "$(ECMC_EC_SLAVE_NUM)")
|
||
#
|
||
#${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=$(ECMC_EC_SLAVE_NUM), HW_DESC=EL7211-0010"
|
||
#
|
||
## Apply local 24V config (local here)
|
||
#${SCRIPTEXEC} ${ecmccfg_DIR}applySlaveConfig.cmd, "LOCAL_CONFIG=./ecmcEL7211-0010-Motor-Beckhoff-AM8121-0F00-0000_24V.cmd"
|
||
#
|
||
##Apply hardware configuration (wrong here, should only be done once (also done in ecmcMCU1021_coupler), but will work)
|
||
#ecmcConfigOrDie "Cfg.EcApplyConfig(1)"
|
||
|
||
#Does not work. Known issue DC-patch for etherlab manster needed...
|
||
#ecmcConfigOrDie "Cfg.EcSelectReferenceDC(0,$(ECMC_EC_SLAVE_NUM))"
|
||
|
||
# ADDITIONAL SETUP
|
||
# Set all outputs to feed switches
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput01,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput02,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput03,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput04,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput05,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput06,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput07,1)"
|
||
ecmcConfigOrDie "Cfg.WriteEcEntryIDString(${ECMC_EC_SLAVE_NUM_DIG_OUT},binaryOutput08,1)"
|
||
# END of ADDITIONAL SETUP
|
||
|
||
##############################################################################
|
||
## AXIS 1: X-axis
|
||
#
|
||
epicsEnvSet("DEV", "$(IOC)")
|
||
$(SCRIPTEXEC) ($(ecmccfg_DIR)configureAxis.cmd, CONFIG=./cfg/x.ax)
|
||
# Set external setpoints
|
||
$(SCRIPTEXEC) ($(ecmccfg_DIR)applyAxisSynchronization.cmd, CONFIG=./cfg/x.sax)
|
||
|
||
##############################################################################
|
||
## AXIS 2: Y-axis
|
||
#
|
||
#epicsEnvSet("DEV", "$(IOC)")
|
||
$(SCRIPTEXEC) ($(ecmccfg_DIR)configureAxis.cmd, CONFIG=./cfg/y.ax)
|
||
# Set external setpoints
|
||
$(SCRIPTEXEC) ($(ecmccfg_DIR)applyAxisSynchronization.cmd, CONFIG=./cfg/y.sax)
|
||
|
||
##############################################################################
|
||
## AXIS 3: Spindle
|
||
#
|
||
#epicsEnvSet("DEV", "$(IOC)")
|
||
#$(SCRIPTEXEC) ($(ecmccfg_DIR)configureAxis.cmd, CONFIG=./cfg/spindle.ax)
|
||
|
||
# Block motor driver printouts
|
||
asynSetTraceMask(MC_CPU1, -1, 0x0)
|
||
|
||
##############################################################################
|
||
## Load plugin:
|
||
epicsEnvSet("PLUGIN_VER" ,"develop")
|
||
require ecmc_plugin_grbl $(PLUGIN_VER)
|
||
|
||
epicsEnvSet(ECMC_PLUGIN_FILNAME,"/home/pi/epics/base-7.0.5/require/${E3_REQUIRE_VERSION}/siteMods/ecmc_plugin_grbl/$(PLUGIN_VER)/lib/${EPICS_HOST_ARCH=linux-x86_64}/libecmc_plugin_grbl.so")
|
||
epicsEnvSet(ECMC_PLUGIN_CONFIG,"DBG_PRINT=1;X_AXIS=1;Y_AXIS=2;AUTO_ENABLE=0;AUTO_START=0;")
|
||
${SCRIPTEXEC} ${ecmccfg_DIR}loadPlugin.cmd, "PLUGIN_ID=0,FILE=${ECMC_PLUGIN_FILNAME},CONFIG='${ECMC_PLUGIN_CONFIG}', REPORT=1"
|
||
epicsEnvUnset(ECMC_PLUGIN_FILNAME)
|
||
epicsEnvUnset(ECMC_PLUGIN_CONFIG)
|
||
|
||
# Load grbl configs (use "ecmcGrblAddConfig()" or "ecmcGrblAddConfig()"):
|
||
# $11 - Junction deviation, mm\n
|
||
# $12 – Arc tolerance, mm\n
|
||
# $30 - Max spindle speed, RPM\n
|
||
# $31 - Min spindle speed, RPM\n
|
||
# $100, $101 and $102 – [X,Y,Z] steps/mm\n
|
||
# $110, $111 and $112 – [X,Y,Z] Max rate, mm/min\n
|
||
# $120, $121, $122 – [X,Y,Z] Acceleration, mm/sec^2\n
|
||
|
||
ecmcGrblLoadConfigFile("./cfg/grbl.cfg")
|
||
|
||
#ecmcGrblAddConfig("$120=1234");
|
||
#ecmcGrblAddConfig("$121=1234");
|
||
#ecmcGrblAddConfig("$122=1234");
|
||
|
||
# Load g-code (use "ecmcGrblLoadGCodeFile()" or "ecmcGrblAddCommand()")
|
||
ecmcGrblLoadGCodeFile("./plc/gcode.nc",0)
|
||
|
||
#ecmcGrblAddCommand("G1X20Y20F360");
|
||
#ecmcGrblAddCommand("G4P2");
|
||
#ecmcGrblAddCommand("G2X0Y0R20");
|
||
#ecmcGrblAddCommand("G4P2");
|
||
#ecmcGrblAddCommand("G0X10Y10");
|
||
#ecmcGrblAddCommand("G4P2");
|
||
#ecmcGrblAddCommand("G1X0Y0");
|
||
|
||
##############################################################################
|
||
## PLC 0: Test some grbl plc commands
|
||
$(SCRIPTEXEC) $(ecmccfg_DIR)loadPLCFile.cmd, "PLC_ID=0, SAMPLE_RATE_MS=1000,FILE=./plc/grbl.plc")
|
||
|
||
##############################################################################
|
||
############# Configure diagnostics:
|
||
|
||
ecmcConfigOrDie "Cfg.EcSetDiagnostics(1)"
|
||
ecmcConfigOrDie "Cfg.EcEnablePrintouts(0)"
|
||
ecmcConfigOrDie "Cfg.EcSetDomainFailedCyclesLimit(100)"
|
||
ecmcConfigOrDie "Cfg.SetDiagAxisIndex(1)"
|
||
ecmcConfigOrDie "Cfg.SetDiagAxisFreq(2)"
|
||
ecmcConfigOrDie "Cfg.SetDiagAxisEnable(0)"
|
||
|
||
$(SCRIPTEXEC) ($(ecmccfg_DIR)setAppMode.cmd)
|
||
|
||
#asynSetTraceMask(MC_CPU1, -1, 0x41)
|
||
# Note need to test 0x21 later..
|
||
#asynSetTraceMask(MC_CPU1, -1, 0x21)
|
||
asynSetTraceMask(MC_CPU1, -1, 0x0)
|
||
|
||
##############################################################################
|
||
############# Go Live:
|
||
|
||
iocInit()
|
||
|
||
dbpf $(IOC):Axis1.SPAM 0
|
||
dbpf $(IOC):Axis2.SPAM 0
|