##############################################################################
# Test to make a triggered scope

##############################################################################
## Initiation:
epicsEnvSet("IOC" ,"$(IOC="IOC_TEST")")
epicsEnvSet("ECMCCFG_INIT" ,"")  #Only run startup once (auto at PSI, need call at ESS), variable set to "#" in startup.cmd
epicsEnvSet("SCRIPTEXEC" ,"$(SCRIPTEXEC="iocshLoad")")

require ecmccfg develop

# run module startup.cmd (only needed at ESS  PSI auto call at require)
$(ECMCCFG_INIT)$(SCRIPTEXEC) ${ecmccfg_DIR}startup.cmd, "IOC=$(IOC),ECMC_VER=develop,stream_VER=2.8.10, EC_RATE=1000"

##############################################################################
## Config hardware:

## Sampel rate in milliseconds
epicsEnvSet("ECMC_SAMPLE_RATE_MS",            "${RATE="1"}")

# Choose sample rate (2, 10 or 100)
epicsEnvSet("ECMC_OVER_SMP",                  "${OVERSAMP="100"}")

# EL1252: trigger on pos edge timestamp
epicsEnvSet("SLAVE_NUM_TRIGG",           "6")
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=$(SLAVE_NUM_TRIGG), HW_DESC=EL1252"

# EL3702: Note: Set NELM to define oversampling rate
epicsEnvSet("SLAVE_NUM_AI",              "11")
${SCRIPTEXEC} ${ecmccfg_DIR}addSlave.cmd, "SLAVE_ID=$(SLAVE_NUM_AI), HW_DESC=EL3702, NELM=${ECMC_OVER_SMP}"

#ecmcConfigOrDie "Cfg.EcSelectReferenceDC(0,$(SLAVE_NUM_TRIGG))"

#Apply hardware configuration
ecmcConfigOrDie "Cfg.EcApplyConfig(1)"

########################################################################s######
## Load plugin: Scope

require ecmc_plugin_scope master  # to get access to db file..

epicsEnvSet(RESULT_NELM, 500)
epicsEnvSet(ECMC_PLUGIN_FILNAME,"${HOME}/epics/base-7.0.4/require/3.3.0/siteMods/ecmc_plugin_scope/master/lib/${EPICS_HOST_ARCH=linux-x86_64}/libecmcPlugin_Scope.so")
epicsEnvSet(ECMC_PLUGIN_CONFIG,"SOURCE=ec0.s${SLAVE_NUM_AI}.mm.CH1_ARRAY;DBG_PRINT=0;TRIGG=ec0.s${SLAVE_NUM_TRIGG}.CH1_LATCH_POS;SOURCE_NEXTTIME=ec0.s${SLAVE_NUM_AI}.NEXT_TIME;RESULT_ELEMENTS=${RESULT_NELM};")
${SCRIPTEXEC} ${ecmccfg_DIR}loadPlugin.cmd, "PLUGIN_ID=1,FILE=${ECMC_PLUGIN_FILNAME},CONFIG='${ECMC_PLUGIN_CONFIG}', REPORT=1"
epicsEnvUnset(ECMC_PLUGIN_FILNAME)
epicsEnvUnset(ECMC_PLUGIN_CONFIG)

dbLoadRecords("ecmcPluginScope.template","P=$(IOC):,PORT=${ECMC_ASYN_PORT},INDEX=0,RESULT_NELM=${RESULT_NELM},RESULT_DTYP=asynInt16ArrayIn,RESULT_FTVL=SHORT")
epicsEnvUnset(RESULT_NELM, 1024)

##############################################################################
############# Configure diagnostics:

ecmcConfigOrDie "Cfg.EcSetDiagnostics(1)"
ecmcConfigOrDie "Cfg.EcEnablePrintouts(0)"
ecmcConfigOrDie "Cfg.EcSetDomainFailedCyclesLimit(100)"

# go active
$(SCRIPTEXEC) ($(ecmccfg_DIR)setAppMode.cmd)

iocInit()
dbl > pvs.log