1 line
6.1 KiB
HTML
1 line
6.1 KiB
HTML
<h2><a name="Variables">TASMAD Variables</a></h2>
|
|
<pre>
|
|
|
|
Variables are divided into five groups:
|
|
|
|
(i) parameters which define some aspect of the instrument configuration
|
|
but are not directly related to a motor angle or power supply value.
|
|
These variables are changed by the SET command.
|
|
|
|
(ii) parameters which relate to the sample.These are also changed by
|
|
SET.
|
|
|
|
(iii) limits and zeroes for motors and power supplies, also changed by
|
|
SET.
|
|
|
|
(iv) Variables which are explicitly or implicitly related to a motor
|
|
position or power supply value. These variables are changed by the
|
|
DRive command.
|
|
|
|
(v) Increments (steps) for the variables of type (iv); these are changed
|
|
by SET.
|
|
|
|
The following list gives the variable identifiers and definitions,
|
|
where the order is as the variables are stored in THE Program.
|
|
|
|
|
|
P.A Variables : Variables marked with an asterisk are not recognized
|
|
unless THE Program is run in polarization analysis mode(see SWitch).
|
|
|
|
|
|
</pre>
|
|
<h3><a name="Instrument_variables">Instrument variables</a></h3>
|
|
<pre>
|
|
|
|
DM Monochromator d-spacing [�].
|
|
DA Analyzer d-spacing [�].
|
|
SM Scattering sense at Mono (+ve to the left)
|
|
SS Scattering sense at Sample (+ve to the left)
|
|
SA Scattering sense at Analyzer (+ve to the left)
|
|
ALF1 Horizontal collimation before mono [minutes FwHm]
|
|
ALF2 Horizontal collimation mono to sample [minutes FwHm]
|
|
ALF3 Horizontal collimation sample to anal. [minutes FwHm]
|
|
ALF4 Horizontal collimation before detector [minutes FwHm]
|
|
BET1 Vertical collimation before mono [minutes FwHm]
|
|
BET2 Vertical collimation mono to sample [minutes FwHm]
|
|
BET3 Vertical collimation sample to analyzer [minutes FwHm]
|
|
BET4 Vertical collimation before detector [minutes FwHm]
|
|
ETAM Monochromator mosaic [minutes FwHm]
|
|
ETAA Analyzer mosaic [minutes FwHm]
|
|
FX =1 for constant Ki; =2 for constant Kf
|
|
NP Number of points in a scan
|
|
TI Preset time [seconds] for a COunt or SCan
|
|
MN Preset monitor for a COunt or SCan
|
|
TO Time-out in for WAit command [minutes]
|
|
DTL lower temperature error allowed [Kelvin]
|
|
DTU upper temperature error allowed [Kelvin]
|
|
|
|
*IF1V IF1V and IF2V are currents [Amps] in the vertical-field
|
|
*IF2V coils for Flipper 1 and Flipper 2.
|
|
*IF1H Horizontal-field currents are KI*IF1H for Flipper1 and
|
|
*IF2H KF*IF2H for F2.
|
|
*HELM Angle between axis of Helmholtz pair one and KI.
|
|
|
|
remark: ALF1 to ETAA are not used by MAD Program but stored for your own
|
|
convenience.
|
|
Please DO NOT FORGET to update ALF1-ALF4 variable after collimator
|
|
change to avoid confusion when you analyse your data after one or
|
|
two years!
|
|
|
|
</pre>
|
|
<h3><a name="Sample_variables">Sample variables</a></h3>
|
|
<pre>
|
|
|
|
AS -\
|
|
BS +-- Sample unit-cell edges [�]
|
|
CS -/
|
|
|
|
AA -\
|
|
BB +-- Sample unit-cell angles [degrees]
|
|
CC -/
|
|
|
|
ETAS Sample mosaic [minutes FwHm]
|
|
|
|
AX -\
|
|
AY +-- Components of a recip. lattice vector in scattering plane
|
|
AZ -/ of the sample. A3 is the angle between KI and (AX,AY,AZ).
|
|
|
|
BX -\
|
|
BY +-- Components of a second distinct recip. lattice vector in
|
|
BZ -/ the sample's scattering plane.
|
|
|
|
</pre>
|
|
<h3><a name="Limits_and_Zeros">Limits and Zeros</a></h3>
|
|
<pre>
|
|
|
|
Lower and upper limits and zeros for all variables given in (iv)
|
|
below. L, U and Z are appended as a prefix to the variable names to
|
|
indicate Lower limit, Upper limit and Zero.
|
|
Storage order is the same as for the corresponding variables, i.e. :
|
|
LA1, UA1, ZA1, LA2, UA2, ZA2, LA3 ...
|
|
(see (iv) below).
|
|
|
|
</pre>
|
|
<h3><a name="Targets_and_Positions">Targets and Positions</a></h3>
|
|
<pre>
|
|
|
|
A1 Monochromator angle (Bragg angle in degrees)
|
|
A2 Scattering angle at mono. (twice Bragg angle in degrees)
|
|
A3 Sample angle (degs) (A3=0 when (AX,AY,AZ) is along KI)
|
|
A4 Scattering angle at sample [degrees]
|
|
A5 Analyzer angle (Bragg angle in deg, TOPSI: not used)
|
|
A6 Scattering angle at analyzer (twice A5 in deg., TOPSI: not used)
|
|
|
|
SINQ Instruments:
|
|
MCV Mono curvature vertical
|
|
SRS Sample table second ring
|
|
ACH Anal curvature horizontal
|
|
MTL Mono lower translation
|
|
MTU Mono upper translation
|
|
STL Sample lower translation
|
|
STU Sample upper translation
|
|
ATL Anal lower translation
|
|
ATU Anal upper translation
|
|
MGL Mono lower goniometer (Reserved)
|
|
MGU Mono upper goniometer
|
|
SGL Sample lower goniometer
|
|
SGU Sample upper goniometer
|
|
AGL Anal lower goniometer (Reserved)
|
|
AGU Anal upper goniometer
|
|
MSC Mono "sample" changer (TASP only)
|
|
ASC Anal "sample" changer (TASP only)
|
|
CSC Collimator "sample" changer (TASP only)
|
|
|
|
D1T D1B D1R D1L Diaphragm 1 (top/bottom/right/left)
|
|
D2T D2B D2R D2L Diaphragm 2 (top/bottom/right/left)
|
|
D3T D3B D3R D3L Diaphragm 3 (top/bottom/right/left)
|
|
|
|
ILL Instruments:
|
|
CH Monochromator changer position [degrees or mm]
|
|
TM (LM) Monochromator translation [(IN20 : 5mm)]
|
|
GM Monochromator goniometer angle [1 unit = 4¡]
|
|
RM Monochromator curvature
|
|
GL Sample goniometer angle; lower arc [1 unit = 4¡]
|
|
GU Sample goniometer angle; upper arc [1 unit = 4¡]
|
|
TA Analyzer translation [ ? mm]
|
|
GA Analyzer goniometer angle [ .4degrees]
|
|
RA Analyzer curvature
|
|
|
|
EI Incident neutron energy [THz or meV]
|
|
KI Incident neutron wavevector [ �-1]
|
|
EF Final neutron energy [THz or meV]
|
|
KF Final neutron wavevector [ �-1]
|
|
|
|
QH -\
|
|
QK +-- Components of Q in Reciprocal Lattice Units [R.L.U.]
|
|
QL -/
|
|
|
|
EN Energy transfer; +ve neutron energy loss [THz or meV]
|
|
QM Length of Q [ �-1]
|
|
TT (T) Temperature of sample thermometer [K]
|
|
TRT(RT) Temperature of regulation thermometer [K]
|
|
(can only be printed out)
|
|
*I1 -\
|
|
*I2 \
|
|
*I3 +-- power supply current values [A]
|
|
. /
|
|
*I11 -/
|
|
|
|
*HX -\ Components of Helmholtz fields at sample in Oersteds.
|
|
*HY +-- HX is parallel to Q and HY is perpendicular to Q in
|
|
*HZ -/ the scattering plane.
|
|
|
|
*F1 -\ Status of flippers one and two; these variables take the
|
|
*F2 -/ values ON or OFF.
|
|
</pre>
|
|
<h3><a name="Increments_Variables">Increments Variables</a></h3>
|
|
<pre>
|
|
For all variables A1 through T in the list of type (iv) variables
|
|
above, the identifier for the step used with a SCan command is obtained
|
|
by prefixing the variable name with the letter D.
|
|
Storage order is DA1, DA2, DA3....etc as for type (iv) variables above.
|
|
|
|
|
|
</pre>
|