sans/config/hmm/detector.tcl
Use dns-name for voltage controller address.
sans/config/motors/motor_configuration.tcl
Set det home position.
SICS-122 Added FastShutter variable and configured det motor with an action object to set the FastShutter variable.
SICS-248 Replaced beamstop motor objects with beamstop action objects.
action.[ch]
The action object factory will eventuall be defined here.
SICS-122 Currently there is just a funcion which sets the FastShutter variable
beamstopaction.c
Added motion control enabled check.
Added "list" subcommand.
Makefile
Compile action.c
motor_dmc2280.c
The status check command now always checks the TI1 and TI0 interrupts.
Added action-object configuration parameter. Call AO_istatus with TI1
if configured with an action object.
r2674 | ffr | 2008-08-13 14:16:30 +1000 (Wed, 13 Aug 2008) | 26 lines
You can now run the oscillating collimator for a specified number of cycles.
A MOTEND event is now sent when the oscillator stops.
Also temporarily set status to eEager to allow changing the motor accesscode parameter while something else is running, (eg a counter)
motor.c
finishDriving is no longer static so we can call it from the oscilator and generate a MOTEND event.
west4100.c
Return 'success' from wrapper on "controlsensor" and "sensorlist" queries so we can test and capture their values in scripts.
Makefile
Compile the quokka beamstopaction object
site_ansto.c
Add the MakeActionObject command. Currently only makes the hardcoded beamstopaction object
obpar.c
Report object name and parameter on an illegal attempt to set a parameter
hmm_configuration_common_1.tcl
Add oscillating collimator control flag for Wombat. If true we use hmm to start the histogram server instead of hmc. TODO remove hmc and always use hmm.
hipd/config/motors/motor_configuration.tcl
Don't load anticollider config twice. Fix oct limits
wombat_configuration.tcl
Environment configuration must be loaded before running server_init.
hrpd/config/hmm/hmm_configuration.tcl
Fix default time-bin to match 10Hz frame frequency
hrpd/config/motors/motor_configuration.tcl
Added dummy motor for testing.
reflectometer/config/hmm/detector.tcl
Fill in dhv1 configuration parameters.
sans/config/hmm/detector.tcl
Enable detector voltage control
sans/config/hmm/hmm_configuration.tcl
SICS-227 set default resolution to 192x192
sans/config/motors/motor_configuration.tcl
Added dummy motor for testing
quokka parameters.tcl
Fix L2mm calculation, Fix SICS-228 users cannot set rotapdeg
beamstopaction.[ch]
NEW: Implements an action command to drive the quokka beamstops up and down.
r2670 | ffr | 2008-08-07 13:17:29 +1000 (Thu, 07 Aug 2008) | 53 lines
server_init now calls ::counter::isc_initialize, ::histogram_memory::isc_initialize and ::scan::isc_initialize
scan.c
SICS-158 Restrict bmonscan and hmscan to only one scan variable
count_common.tcl
Create a mulicounter which uses the available monitors as channels. The multicounter is used in bmonscans
hipadaba_configuration_common.tcl
Use _link as the suffix for the nxvgroup name when making nexus file links.
hmm_configuration_common.tcl
SICS-190 Create hdb entries for bm_counts, bm_event_rate, bm_status
SICS-164 Allow running histmem in simulated mode.
hmm_cylindrical_detector_configuration.tcl
Only refer to detector SICSVariables when necessary, otherwise we get dependency problems.
nxscripts_common_1.tcl
Separate histmem_filtype_spec from bmon_filetype_spec so that we can use the histem_filetyp_spec names to restrict the histmem scan filetypes.
Close the data file on error in proc ::nexus::save
Allow int and text types when saving macro data
scan_common_1.tcl
SICS-173 Allow users to force a scan when the instrument isn't ready
Added ic_initialize proc so we can make dependencies explicit in the init_server proc
SICS-186 Allow monitor modes for histmem scans
Allow selection of histmem file policies from runscan command
echidna, wombat, kowari, quokka and platypus component and server configurations
Added instrument specific configuration initialisation functions in the component configuration files.
Add a catch block to the top-level instrument server configuration file and printout the errorContext and callStack
r2641 | ffr | 2008-07-01 17:02:26 +1000 (Tue, 01 Jul 2008) | 34 lines
