the capture command in that it not put resluts into the Tcl interpreter.
This broke scriptcontext scripts in complicated situations.
- Resolved some issues with the TAS calculation and negative scattering sense.
- Fixed a bug which did not reset the state to idle after checking
reachability in confvirtualmot.c
SKIPPED:
psi/autowin.c
psi/eigera2.c
psi/jvlprot.c
psi/makefile_linux
psi/sinqhttpopt.c
psi/tasscan.c
- Removed generation of incommenurate reflections for 0,0,0 in fourmess.c
- Implemented a Poch command for heartbeats
- Fixed 64 bit dimension issues in nxdict
- Fixed different calling conventions for NXReportError deep stack in nxdict
- Stopped ei motor driving when not necessary
- Added yet another monitor for POLDI
- Added a protocoll driver for the JVL motor RS-485 binary protocoll
- Fixed some reporting issues
SKIPPED:
psi/jvlprot.c
psi/make_gen
psi/polterwrite.c
psi/psi.c
psi/spss7.c
- New NeXus libraries
- Added new raw binary transfer mode for mass data
- Added a check script option to configurable virtual motor
SKIPPED:
psi/dumprot.c
psi/make_gen
psi/psi.c
psi/rebin.c
psi/sanslirebin.c
- Added a warning for excessive data rates on monitors
- Added statistics to devser and thus to scriptcontext
- Added byte concatenation to dynstring
- Added aborting for reflection generation to fourmess.c
- Added data checksum testing to hipadaba, use for update tests
- Fixed interrupt discovery in network.c, caused invalid interrupt
codes which in turn confused sicscron which had to be fixed too.
- Renamed ubcalc into ubcalcint in order to reclaim the ubcalc for Jurg
- Added an a3offset to tasub in order to fix what I perceive an IS problem
- Added support for the newer version of the Siemens SPS, the S7
- Added a not yet fully working sinqhttpopt driver which talks to
http HM without libghttp
SKIPPED:
psi/delcam.c
psi/make_gen
psi/psi.c
psi/sinq.c
psi/sinq.h
psi/sinqhttpopt.c
psi/slsvme.c
psi/spss7.c
syntax checking input purposes
- Rectified an error message in fourmess.c
- HMcontrol did not check for the HM to stop before returning. This
caused weird data files at AMOR as the data had not yet been downloaded
from the HM.
- Fixed an issue about parameters in multicounter
- Temporary fix in nxscript.c to always read the Hm from the HM and not
a buffer. This is prior to rethinking caching strategies for old style
HM's.
- Synchronize now copies fixed motors correctly. This used to cause
irritation with users. This now requires a script syncdrive to exist
in the sync server which takes care of handling the fixed flag when
this is desired.
- Added initify to sicsdata in order to copy large value timebins over
properly at AMOR
SKIPPED:
psi/amorstat.c
psi/make_gen
psi/makefile_linux
psi/polterwrite.c
psi/sinq.c
psi/sinqhttp.c
psi/sinqhttpprot.c
psi/sps.c
psi/tdchm.c
shutdown when nothing works as it should
- Made an attempt to have all error message printed on demand
- Added a tricsswap feature to sinqhttp which swaps the data right for SICS
- Edited speed for phytron driver
- First attack on adding a misalignment calculation to tasub
- Added a test protocol for scriptcontext which can be configured.
SKIPPED:
psi/sinqhttp.c
- Fixed a stack overrun bug in macro.c
- Fixed a killing bug in devser.c
- Added node writing with offset to nxscript.c
- Wrote a simulation driver for second generation HM's
- Readded devexec commands to SICS
- Readded Hipadaba initialisation to SICS
- Fixed a bug in sinqhttprot.c which is triggered when a reconnect happens
during a node based download of data.
SKIPPED:
psi/sinqhttpprot.c
- Implemented the desired run/drive behaviour: drive waits for what it started
run starts, and success waits for everything to finish. This required
changes to a lot of files.
- Fixed a bug in remob which supressed required messages
- Added new ACT protocol
- Extended sicshdbadapter to cover counters and status to put the status
into Hipadaba
- Fixes to napi5.c
- Exe now supports hdbrun which allows to write output for a buffer into
hdb node.
- Fixed a bug in hmdata.c
- Fixed an issue with tempoerature writing through RemObjects in mesure
- Added auxiliary reflections to tasub
- Make maximize use soft motor positions
- Fixes to make RITA work
- tasub extended to calculate UB from cell alone, support for elastic mode
- New MultiCounter as abstraction for counting on HM's
- regression test driver for counters
- Changes to Hipadaba
- Added project to histogram memory code
- Started regression testing code
- Added hill climbing as optimization method to optimise
- Fixed new AMOR settings module
- Initial implementation of the new SICS hierarchical parameter database
SKIPPED:
psi/amorset.c
psi/libpsi.a
psi/sps.c
- Mended tasdrive to drive energy even if Q is askew
- Fixed QM values
- Fixed problems in mesure: om2th, wrong theta selection
- Fixed core dump when driving h,kl, failed
a connection during an active run.
- Added an additional output mode for the connection in order to
support the batch run editor.
- Made clientput send everything with eWarning mode in order to support
the batch run editor.
- Added a better NetReadTillTerm
- Fixed a problem in synchronize.c
- Fixed an issue with reading empty line on normal connection sockets.
- Added a psi scan mode to mesure.c for TRICS
- Made motor print warnings when trying to reposition.
- Fixed abug in hkl.c which cause wrong signs.
SKIPPED:
psi/el734driv.c
psi/el734hp.c
psi/el737driv.c
psi/el737hpdriv.c
psi/nextrics.c
psi/nxamor.c
psi/psi.c
psi/slsmagnet.c
psi/swmotor2.c
psi/tasscan.c
psi/tasutil.c
