Firmware Upgrade ================= Eiger ------------- Download ^^^^^^^^^^^^^ - `bcp script `__ - detector server corresponding to package in slsDetectorPackage/serverBin - `bit files `__ Upgrade ^^^^^^^^ #. Tftp must be already installed on your pc to use the bcp script. #. Copy new servers to the board. See :ref:`how to upgrade detector servers` for more detals. A reboot should have started the new linked servers automatically. For Eiger, do not reboot yet as we need to program the firmware via bit files. * This step is crucial when registers between firmwares change. Failure to do so will result in linux on boards to crash and boards can't be pinged anymore. #. Bring the board into programmable mode using either of the 2 ways. Both methods result in only the central LED blinking. * **Manual:** Do a hard reset for each half module on back panel boards, between the LEDs, closer to each of the 1G ethernet connectors. Push until all LEDs start to blink. * Software: .. code-block:: bash # Option 1: if the old server is still running: sls_detector_put execcommand "./boot_recovery" # Option 2: ssh root@bebxxx cd executables ./boot_recovery #. Start a terminal for each half module and run the following to see progress. .. code-block:: bash nc -p 3000 -u bebxxx 3000 # Press enter twice to see prompt with board name. > bebxxx # After each bcp command, wait for this terminal to print "Success". #. In another terminal, run the following to update firmware. Please update bit files with great caution as it could make your board inaccessible, if done incorrectly. .. code-block:: bash #update back end fpga bcp download.bit bebxxx:/fw0 #update front left fpga bcp download.bit bebxxx:/febl #update front right fpga bcp download.bit bebxxx:/febr #update kernel (only if required by the SLS Detector Group) bcp download.bit bebxxx:/kernel #. Reboot the detector. .. code-block:: bash # reconfig febX is necessary only if you have flashed a new feb firmware reconfig febl reconfig febr # will reboot controller reconfig fw0 .. note :: If not already there, you need to add scripts to automatically start detector server upon power on. See :ref:`Automatic start` for more details. Jungfrau ------------- Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - `pof files `__ Upgrade ^^^^^^^^ .. note :: These instructions are for upgrades from v5.0.0. For earlier versions, contact us. Check :ref:`firmware troubleshooting ` if you run into issues while programming firmware. Always ensure that the client and server software are of the same release. #. Program from console .. code-block:: bash # copies server from tftp folder of pc, links new server to jungfrauDetectorServer, # removes old server from respawn, sets up new lnked server to respawn # programs fpga, # reboots sls_detector_put update jungfrauDetectorServervxxx pcxxx xx.pof # Or only program firmware sls_detector_put programfpga xxx.pof Gotthard I ----------- Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - `pof files `__ .. _firmware upgrade using blaster for blackfin: Upgrade ^^^^^^^^ .. warning :: | Gotthard firmware cannot be upgraded remotely and requires the use of USB-Blaster. | It is generally updated by the SLS Detector group. #. Download `Altera Quartus software or Quartus programmer `__. #. Start Quartus programmer, click on Hardware Setup. In the "Currently selected hardware" window, select USB-Blaster. #. In the Mode combo box, select "Active Serial Programming". #. Plug the end of your USB-Blaster with the adaptor provided to the connector 'AS config' on the Gotthard board. #. Click on 'Add file'. Select programming (pof) file provided by the SLS Detector group. #. Check "Program/Configure" and "Verify". Push the start button. Wait until the programming process is finished. #. In case of error messages, check the polarity of cable (that pin1 corresponds) and that the correct programming connector is selected. #. Reboot the detector. Mythen III ----------- .. note :: As it is still in development, the rbf files must be picked up from the SLS Detector Group. Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - rbf files (in developement) Upgrade ^^^^^^^^ Always ensure that the client and server software are of the same release. #. Program from console .. code-block:: bash # copies server from tftp folder of pc, links new server to jungfrauDetectorServer, # programs fpga, # reboots sls_detector_put update mythen3DetectorServervxxx pcxxx xxx.rbf # Or only program firmware sls_detector_put programfpga xxx.rbf .. note :: If not already there, you need to add scripts to automatically start detector server upon power on. See :ref:`Automatic start` for more details. Gotthard II ------------- Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - `rbf files `__ Upgrade ^^^^^^^^ Always ensure that the client and server software are of the same release. #. Program from console .. code-block:: bash # copies server from tftp folder of pc, links new server to jungfrauDetectorServer, # programs fpga, # reboots sls_detector_put update gotthard2DetectorServervxxx pcxxx xxx.rbf # Or only program firmware sls_detector_put programfpga xxx.rbf .. note :: If not already there, you need to add scripts to automatically start detector server upon power on. See :ref:`Automatic start` for more details. Moench ------- Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - `pof files `__ Upgrade ^^^^^^^^ Check :ref:`firmware troubleshooting ` if you run into issues while programming firmware. Always ensure that the client and server software are of the same release. #. Program from console .. code-block:: bash # copies server from tftp folder of pc, links new server to jungfrauDetectorServer, # removes old server from respawn, sets up new lnked server to respawn # programs fpga, # reboots sls_detector_put update moenchDetectorServervxxx pcxxx xx.pof # Or only program firmware sls_detector_put programfpga xxx.pof Ctb ---- Download ^^^^^^^^^^^^^ - detector server corresponding to package in slsDetectorPackage/serverBin - `pof files `__ Upgrade ^^^^^^^^ Check :ref:`firmware troubleshooting ` if you run into issues while programming firmware. Always ensure that the client and server software are of the same release. #. Program from console .. code-block:: bash # copies server from tftp folder of pc, links new server to jungfrauDetectorServer, # removes old server from respawn, sets up new lnked server to respawn # programs fpga, # reboots sls_detector_put update ctbDetectorServervxxx pcxxx xx.pof # Or only program firmware sls_detector_put programfpga xxx.pof .. _blackfin firmware troubleshooting: Firmware Troubleshooting with blackfin ---------------------------------------- 1. v4.x.x client after programming will most likely reboot the blackfin processor, regardless of error. 2. v5.x.x-rcx client after programming will not reboot the blackfin processor, if error occurred. 3. If a reboot occured with an incomplete firmware in flash, the blackfin will most likely not find the mtd3 drive. To see if this drive exists: .. code-block:: bash # connect to the board telnet bchipxxx # view of mtd3 existing root:/> more /proc/mtd dev: size erasesize name mtd0: 00040000 00020000 "bootloader(nor)" mtd1: 00100000 00020000 "linux kernel(nor)" mtd2: 002c0000 00020000 "file system(nor)" mtd3: 01000000 00010000 "bitfile(spi)" 4. If one can see the mtd3 drive, one can already try to flash again using the **programfpga** command (without rebooting blackfin or detector). 5. If one can't list it, read the next section to try to get the blackfin to list it. How to get back mtd3 drive remotely (copying new kernel) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ .. code-block:: bash # step 1: get the kernel image (uImage.lzma) from slsdetectorgroup # and copy it to pc's tftp folder # step 2: connect to the board telnet bchipxxx #step 3: go to directory for space cd /var/tmp/ # step 3: copy kernel to board tftp pcxxx -r uImage.lzma -g # step 4: verify kernel copied properly ls -lrt # step 5: erase flash flash_eraseall /dev/mtd1 # step 6: copy new image to kernel drive cat uImage.lzma > /dev/mtd1 # step 7: sync # step 8: reboot # step 9: verification telnet bchipxxx uname -a # verify kernel date more /proc/mtd # verify mtd3 is listed Last Resort using USB Blaster ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ If none of these steps work, the last resort might be physically upgrading the firmware using a USB blaster, which also requires opening up the detector. Instructions for all the blackfin detectors are the same as the one for :ref:`gotthard firmware upgrade `.