* voltage regulators only looks at dac and not at ctrl_reg
* xilinx: change dac max to 2048, setting dac ist not inverse conversion from dac to voltage anymore, but setting power is inverse, also there is max and min to power, a different min for vio and this is checked at funcs interface, not printign or converting to mv in dac for power regulators (as its conversion max and min are different)
* Use links for dacs/adc and adapt power rglt thresholds
* Remove wait for transceiver reset
* adc and dac device not used anymore and hence removed
* udp restucturing: arm has to be multiple of 16 and no byteswap in udp_gen, option to compile locally in arm architecture, memsize of the second udp memory has to be limited
---------
Co-authored-by: Martin Brückner <martin.brueckner@psi.ch>
* changed common.c readADCFromFile to make it more general and move temperature calculation for Eiger out of this function and inside whereever it is called.
* g2 and m2: gethighvoltage was just a variable set in server, it is now moved to a get inside DAC5671 implementation (but not reading a measured value, instead what is set from a file), high voltage variable used inside DAC5671 for virtual servers
* g2: switching off hv (ifrom non zero to zero value) will wait for 10s; powering on chip reconfigures chip; powering off chip unconfigures chip; powering off chip also includes check if hv = 0, if not throw exception; chip configuration checked before acquring; at start up: hv switched off and chip powered on, so does not wait 10s to switch off hv;
* included test to check powering off chip when hv is on should throw an exception
* g2: check if chip configured before acquiring
* nios: read hv value set from file and virtual still goes into DAC5671 for conversions to and fro dac to V, change common readadc to readparameter to generalize, make sethighvoltage into a get and set to catch errors in get as well, g2: if not at startup, remmeber hv value before setting it and after check if value was being switched off (from a non zero value) and wait 10s if it was (10s wait only for switching off from non zero and not at startup)
* period and exptime(patternwaittime level 0)
* added new regsieterdefs and updated api version and fixedpattern reg
* autogenerate commands
* formatting
* minor
* wip resetflow, readout mode, transceiver mask, transceiver enable
* acquisition, but streaming done bit and busy (exposing + read chip to fifo) not known yet from fw
* programming fpga and device tree done
* most configuration done, need to connect configuretransceiver to client
* stuck at resetting transciever timed out
* minor
* fixed virtual, added chip busyto fifo, streaming busy, set/getnext framenumber
* configuretransceiver from client, added help in client
* make formatt and command generation
* tests for xilinx ctb works
* command generation
* dacs added and tested, power not done
* power added
* added temp_fpga
* binaries in
* ctrlreg is 0 to enable chip=fixed, high dac val = min val= fixed, power regulators in weird order=fixed, device tree could be loaded with dacs before adcs=fixed
* start works
* virtual server sends
* receiver works
* tests
* python function and enum generation, commands generatorn and autocomplete, formatting, tests
* tests fail at start(transceiver not aligned)
* tests passed
* all binaries compiled
* eiger binary in
* added --nomodule cehck for xilinx
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* connected kernelversion, hardwareversion, versions, framesl, triggersl, dr, timingmode, pattern (except patioctrl) thats there for altera ctb
* replaced set/get64Bit to set/getU64bit in all loadpattern.c for (ctb and m3 also)
* implemented testbus, testfpga, set/get #frames, triggers, allowed that and for connection to client, also allowed, getnumchannels, configuremac, getrunstatus, setdetectorposition with dummy values
* allowing tests for xilinx
* binaries in
* updated registers, arm64
* compiler set to aarch64 for xilinx server
* updated RegisterDefs.h
* merge into generate branch and resolving conflicts and adding the xilinx changes to callerspecial and commands.yaml
* compiles and can print firmware version (using a different csp0 address)
* fixing other servers (gotthard, jungfrau, moench, mythen3) that it returns in case of mapping failure, xilinxctb: added that it checks type, prints proper fw version, checks kernel date, added armprocessor define to use in common places, added specifiers to supress overflow and truncation warnings
* added detector ip and mac adddress to the printout
* fixed tests and recompiled servers
