jungfrau: flip rows and partial readout only available for hw2.0

RELEASE.txt

@@ -67,6 +67,9 @@ This document describes the differences between v6.0.1 and v6.0.0.
     2.  [Gotthard2][Mythen3]  
         Verifies kernel version at server start up.
 
+    3.  [Jungfrau]
+        Verifies HW2.0 before trying to set read n rows or flip rows.
+
 
     Client
     ------
@@ -85,6 +88,11 @@ This document describes the differences between v6.0.1 and v6.0.0.
 
     1.  Setting receiver hostname to "none" threw an exception. Fixed.
 
+    2.  [Jungfrau]
+        Since the server verifies HW2.0 for number of rows before trying to set it, 
+        the receiver now does not show incorrect missing packets stemming from this 
+        issue.
+
 
 
 3. Firmware Requirements

slsDetectorServers/jungfrauDetectorServer/slsDetectorFunctionList.c

@@ -501,13 +501,15 @@ void setupDetector() {
     // temp threshold and reset event
     setThresholdTemperature(DEFAULT_TMP_THRSHLD);
     setTemperatureEvent(0);
-    setFlipRows(DEFAULT_FLIP_ROWS);
     if (getChipVersion() == 11) {
         setFilterResistor(DEFAULT_FILTER_RESISTOR);
         setNumberOfFilterCells(DEFAULT_FILTER_CELL);
     }
+    if (!isHardwareVersion2()) {
+        setFlipRows(DEFAULT_FLIP_ROWS);
         setReadNRows(MAX_ROWS_PER_READOUT);
     }
+}
 
 int resetToDefaultDacs(int hardReset) {
     LOG(logINFOBLUE, ("Resetting %s to Default Dac values\n",
@@ -1671,6 +1673,11 @@ int setReadNRows(int value) {
         LOG(logERROR, ("Invalid number of rows %d\n", value));
         return FAIL;
     }
+    if (isHardwareVersion2()) {
+        LOG(logERROR, ("Could not set number of rows. Only available for "
+                    "Hardware Board version 2.0.\n"));
+        return FAIL;
+    }
 
     // regval is numpackets - 1
     int regval = (value / READ_N_ROWS_MULTIPLE) - 1;
@@ -1679,7 +1686,6 @@ int setReadNRows(int value) {
     bus_w(addr, bus_r(addr) & ~READ_N_ROWS_NUM_ROWS_MSK);
     bus_w(addr, bus_r(addr) | ((regval << READ_N_ROWS_NUM_ROWS_OFST) &
                                READ_N_ROWS_NUM_ROWS_MSK));
-
     if (value == MAX_ROWS_PER_READOUT) {
         LOG(logINFO, ("Disabling Partial Readout (#rows)\n"));
         bus_w(addr, bus_r(addr) & ~READ_N_ROWS_ENBL_MSK);
@@ -1691,6 +1697,10 @@ int setReadNRows(int value) {
 }
 
 int getReadNRows() {
+    // cannot set it in old board
+    if (isHardwareVersion2()) {
+        return MAX_ROWS_PER_READOUT;
+    }
     int enable = (bus_r(READ_N_ROWS_REG) & READ_N_ROWS_ENBL_MSK);
     int regval = ((bus_r(READ_N_ROWS_REG) & READ_N_ROWS_NUM_ROWS_MSK) >>
                   READ_N_ROWS_NUM_ROWS_OFST);
@@ -2163,6 +2173,11 @@ int getFlipRows() {
 }
 
 void setFlipRows(int arg) {
+    if (isHardwareVersion2()) {
+        LOG(logERROR, ("Could not set flip rows. Only available for "
+                "Hardware Board version 2.0.\n"));
+        return;
+    }
     if (arg >= 0) {
         if (arg == 0) {
             LOG(logINFO, ("Switching off bottom row flipping\n"));

slsDetectorServers/slsDetectorServer/src/slsDetectorServer_funcs.c

@@ -4663,6 +4663,13 @@ int set_read_n_rows(int file_des) {
                         "of %d\n",
                         arg, READ_N_ROWS_MULTIPLE);
                 LOG(logERROR, (mess));
+            }         
+            // only for HW 2.0 (version = 3)
+            else if (isHardwareVersion2()) {
+                ret = FAIL;
+                strcpy(mess, "Could not set number of rows. Only available for "
+                            "Hardware Board version 2.0.\n");
+                LOG(logERROR, (mess));
             } else
 #endif
             {
@@ -4702,7 +4709,7 @@ int get_read_n_rows(int file_des) {
     retval = getReadNRows();
     if (retval == -1) {
         ret = FAIL;
-        sprintf(mess, "Could not get numbr of rows. \n");
+        sprintf(mess, "Could not get number of rows. \n");
         LOG(logERROR, (mess));
     } else {
         LOG(logDEBUG1, ("number of rows retval: %u\n", retval));