hinger_v
73938aad04
new file: BP_analysis_thinSensors.cpp new file: BP_fit.cpp new file: BP_fit_M431.cpp new file: BP_fit_thin.cpp new file: BP_scan_both_speeds.sh new file: BP_scan_thinSensor.sh new file: CS_analysis_M431.cpp new file: CS_analysis_M439.cpp new file: CS_fit.cpp new file: CS_fit_M431 new file: CS_fit_M431.cpp new file: CS_scan_both_speeds.sh new file: CuFluo_exposure_both_speeds.sh new file: CuFluo_fit.cpp new file: Default_pixels_arrays.cpp
176 lines
4.2 KiB
Bash
176 lines
4.2 KiB
Bash
#!/bin/bash
|
|
|
|
# to run do: bash BP_scan.sh
|
|
|
|
# prerequisites:
|
|
# - setup_env.sh souced
|
|
# - the hostname is set
|
|
# - detector is on
|
|
# - Filename_creator has been run (with correct module #)
|
|
# - source pccalib.sh with pc (pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02)
|
|
# - waveform generator is on
|
|
# - amplifier board is powered and unconnected.
|
|
# - last file should be 2097184000 bytes big.
|
|
# connect to pc10773 (RH7 machine connected to the pulser and, after klog, run the command
|
|
# nc -k -n -v -l -p 5555 -e /bin/bash
|
|
|
|
# last data file (000002.dat) should be 2097184000 bytes
|
|
|
|
|
|
|
|
KILLRCV="killall ju_udp_receiver_3threads_2_0"
|
|
$KILLRCV
|
|
|
|
|
|
sls_detector_put stop #just in case
|
|
|
|
|
|
sls_detector_put powerchip 1
|
|
|
|
|
|
sls_detector_put delay 0
|
|
sls_detector_put triggers 1
|
|
sls_detector_put frames 100
|
|
sls_detector_put period 0.005
|
|
sls_detector_put exptime 0.00004
|
|
#sls_detector_put highvoltage 0
|
|
|
|
# configure for receiver on pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02
|
|
# source pccalib.sh with pc (pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02)
|
|
|
|
sls_detector_put udp_dstport 32410
|
|
sls_detector_put udp_dstip $DSTIP #10.1.4.105
|
|
sls_detector_put udp_dstmac $DSTMAC #3C:FD:FE:A2:14:D8
|
|
sls_detector_put udp_srcip $SRCIP #10.1.4.9
|
|
sls_detector_put udp_srcmac 00:ab:be:cc:dd:e2
|
|
|
|
#sls_detector_put configuremac 0
|
|
#sls_detector_put readoutspeed half_speed
|
|
sls_detector_put readoutspeed full_speed
|
|
|
|
sls_detector_put gainmode dynamic
|
|
|
|
CLI=/afs/psi.ch/project/sls_det_software/serial_control_software/minidelay/minidelay
|
|
|
|
# prepare the AGILENT 33250A
|
|
echo $CLI" OUTP OFF " | nc pc10773 5555
|
|
|
|
sleep 0.2
|
|
|
|
#remember to put High-Z load!
|
|
#Change load to Infinity
|
|
echo $CLI" OUTP:LOAD INF " | nc pc10773 5555
|
|
|
|
# Polarity normal
|
|
echo $CLI" OUTP:POL NORM" | nc pc10773 5555
|
|
|
|
# pulse
|
|
echo $CLI" FUNC PULS" | nc pc10773 5555
|
|
sleep 0.2
|
|
# frequency 1kHz
|
|
echo $CLI" FREQ 1000" | nc pc10773 5555
|
|
sleep 0.2
|
|
# width 40 us
|
|
echo $CLI" PULS:WIDT 0.000040" | nc pc10773 5555
|
|
sleep 0.2
|
|
# amplitude 0.1 V" | nc pc10773 5555
|
|
echo $CLI" VOLT 0.1" | nc pc10773 5555
|
|
# offset 0 V echo $CLI" VOLT:OFFS 0" | nc pc8830 5555
|
|
sleep 0.2
|
|
# VLOW 0 V
|
|
echo $CLI" VOLT:LOW 0" | nc pc10773 5555
|
|
sleep 0.2
|
|
# edge 50 ns
|
|
echo $CLI" PULS:TRAN 0.000000050" | nc pc10773 5555
|
|
sleep 0.2
|
|
# triggered burst
|
|
echo $CLI" BURS:MODE TRIG" | nc pc10773 5555
|
|
sleep 0.2
|
|
# cycles 1
|
|
echo $CLI" BURS:NCYC 1" | nc pc10773 5555
|
|
sleep 0.2
|
|
# external trigger source
|
|
echo $CLI" TRIG:SOUR EXT" | nc pc10773 5555
|
|
sleep 0.2
|
|
# delay 1 us
|
|
echo $CLI" TRIG:DEL 0.000001" | nc pc10773 5555
|
|
# delay 40 us
|
|
#echo $CLI" TRIG:DEL 0.000040" | nc pc10773 5555
|
|
sleep 0.2
|
|
# slope positive
|
|
echo $CLI" TRIG:SLOP POS" | nc pc10773 5555
|
|
sleep 0.2
|
|
# turn on burst mode
|
|
echo $CLI" BURS:STAT ON" | nc pc10773 5555
|
|
sleep 0.2
|
|
|
|
|
|
if [ "$1" == 'Y' ]; then
|
|
echo "started with Y argument, skipping manual checks"
|
|
else
|
|
echo "It is now safe to connect the cable between the amplifier board and the readout board"
|
|
echo "Please do so and press any key to continue, or press q to exit this script"
|
|
read -n 1 -s input
|
|
if [[ $input = "q" ]]; then
|
|
echo "Exiting script"
|
|
exit 1
|
|
fi
|
|
fi
|
|
|
|
|
|
# high voltage
|
|
# sls_detector_put highvoltage 200 #because it seemed more stable, we are using external HV 230V
|
|
# output on
|
|
echo $CLI" OUTP ON" | nc pc10773 5555
|
|
sleep 0.2
|
|
|
|
|
|
if [ "$1" == 'Y' ]; then
|
|
echo "started with Y argument, skipping manual checks"
|
|
else
|
|
|
|
echo "The current on the amplifier board should be ~0.035 A"
|
|
echo "Please check and press any key to continue, or press q to exit this script"
|
|
read -n 1 -s input
|
|
if [[ $input = "q" ]]; then
|
|
echo "Exiting script"
|
|
exit 1
|
|
fi
|
|
fi
|
|
|
|
$TKBPG0 &
|
|
|
|
|
|
# the scan
|
|
for ivpulse in {10..700..5}
|
|
do
|
|
|
|
vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
|
|
echo $CLI" VOLT:HIGH "$vpulse | nc pc10773 5555
|
|
sleep 1
|
|
sls_detector_put start
|
|
sleep 1
|
|
done
|
|
|
|
for ivpulse in {750..6000..50}
|
|
do
|
|
vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
|
|
echo $CLI" VOLT:HIGH "$vpulse | nc pc10773 5555
|
|
sleep 1
|
|
sls_detector_put start
|
|
sleep 1
|
|
done
|
|
|
|
|
|
# high voltage
|
|
# sls_detector_put highvoltage 0
|
|
# output off
|
|
echo $CLI" OUTP OFF " | nc pc10773 5555
|
|
|
|
$KILLRCV
|
|
|
|
echo "Finished scan, please wait for capacitor to discharge"
|
|
sleep 20
|
|
echo "It is now safe to disconnect the cable between the amplifier board and the readout board"
|
|
echo "Script finished"
|