hinger_v
ed18504809
modified: BP_scan.sh modified: BP_scan_JF11.sh modified: CS_analysis.cpp modified: CS_analysis_JF11 modified: CS_scan.sh modified: CS_scan_JF11.sh modified: CuFluo_exposure.sh modified: filename_creator.sh modified: makefile modified: pccalib.sh modified: run_JFCalibration.txt modified: slsDetector_bin modified: CS_analysis.cpp BP_analysis_M431.cpp BP_analysis_thin.cpp BP_fit.cpp BP_fit_M431.cpp BP_fit_thin.cpp BP_scan_both_speeds.sh BP_scan_thinSensor.sh CS_analysis_M431.cpp CS_analysis_M439.cpp CS_fit.cpp CS_fit_M431.cpp CS_scan_both_speeds.sh CuFluo_exposure_both_speeds.sh CuFluo_fit.cpp Default_pixels_arrays.cpp
216 lines
5.3 KiB
Bash
216 lines
5.3 KiB
Bash
#!/bin/bash
|
|
|
|
# to run do: bash BP_scan.sh 0/1
|
|
# arg 1 specify if normal or HG0G1G2 setting
|
|
# 1.1 needs file in the blackfin
|
|
|
|
# prerequisites:
|
|
# - setup_env.sh souced
|
|
# - the hostname is set
|
|
# - detector is on
|
|
# - waveform generator is on
|
|
# - amplifier board is powered and unconnected.
|
|
|
|
# connect to pc8830 (or any RH7 machine connected to the pulser and, after klog, run the command
|
|
# nc -k -n -v -l -p 5555 -e /bin/bash
|
|
|
|
|
|
KILLRCV="killall ju_udp_receiver_3threads_2_0"
|
|
$KILLRCV
|
|
|
|
|
|
if [ "$1" == "" ] || [ $# -gt 1 ]; then
|
|
echo "Parameter 1 is empty specify G0 for normal, HG0 for HG0G1G2"
|
|
return 0
|
|
fi
|
|
|
|
sls_detector_put stop;
|
|
sls_detector_put powerchip 0
|
|
sleep 3
|
|
#sls_detector_put setbit 0x5d 7
|
|
sls_detector_put powerchip 1
|
|
|
|
CLI=/afs/psi.ch/project/sls_det_software/serial_control_software/minidelay/minidelay
|
|
|
|
#sls_detector_put setbit 0x5d 0
|
|
|
|
sls_detector_put delay 0
|
|
sls_detector_put triggers 1
|
|
sls_detector_put frames 100
|
|
sls_detector_put period 0.005
|
|
sls_detector_put exptime 0.000040
|
|
sls_detector_put highvoltage 0
|
|
|
|
# configure for receiver on mpc2012
|
|
sls_detector_put udp_dstport 32410
|
|
sls_detector_put udp_dstip $DSTIP #10.1.4.105
|
|
sls_detector_put udp_dstmac $DSTMAC #3C:FD:FE:A2:14:D8
|
|
sls_detector_put udp_srcip 10.1.5.9 #wrong on purpose, so we send some packets to nowhere
|
|
sls_detector_put udp_srcmac 00:ab:be:cc:dd:e2
|
|
#sls_detector_put configuremac 0
|
|
sls_detector_put readoutspeed 1
|
|
sls_detector_put start # this puts the chip in a known state. packets to nowhere
|
|
sls_detector_put stop
|
|
|
|
|
|
sls_detector_put udp_srcip $SRCIP #10.1.4.9 #now the right one.
|
|
|
|
sleep 3
|
|
|
|
if [ "$1" == 'HG0' ]; then
|
|
sls_detector_put settings highgain0
|
|
RCVON=$TKBPHG0
|
|
echo $RCVON
|
|
#sls_detector_put reg 0x58 0x00800f ; sls_detector_put setbit 0x58 31 ; sls_detector_put clearbit 0x58 31;
|
|
echo "HG0G1G2 mode"
|
|
else
|
|
sls_detector_put settings gain0
|
|
RCVON=$TKBPG0
|
|
echo $RCVON
|
|
#sls_detector_put reg 0x58 0x10800f ; sls_detector_put setbit 0x58 31 ; sls_detector_put clearbit 0x58 31;
|
|
echo "normal mode"
|
|
fi
|
|
|
|
sls_detector_put reg 0x7f 0xff1f
|
|
#sls_detector_put reg 0x59 0x1110
|
|
|
|
sleep 1
|
|
|
|
#sls_detector_put reg 0x5b 0xffffffff
|
|
#sls_detector_put reg 0x5a 0xffffffff
|
|
sleep 1
|
|
#sls_detector_put setbit 0x58 30 ; sleep 1 ;sls_detector_put clearbit 0x58 30;
|
|
sleep 1
|
|
|
|
|
|
|
|
|
|
|
|
#sls_detector_put reg 0x5b 0xffffffff
|
|
#sls_detector_put reg 0x5a 0xffffffff
|
|
#sls_detector_put setbit 0x5d 16
|
|
#sls_detector_put start;
|
|
#sls_detector_put stop;
|
|
#sls_detector_put clearbit 0x5d 16
|
|
|
|
|
|
# prepare the AGILENT 33250A
|
|
echo $CLI" OUTP OFF " | nc pc10773 5555
|
|
|
|
sleep 0.2
|
|
|
|
#remember to put High-Z load!
|
|
#Change load to Infinity
|
|
echo $CLI" OUTP:LOAD INF " | nc pc10773 5555
|
|
|
|
# Polarity normal
|
|
echo $CLI" OUTP:POL NORM" | nc pc10773 5555
|
|
|
|
# pulse
|
|
echo $CLI" FUNC PULS" | nc pc10773 5555
|
|
sleep 0.2
|
|
# frequency 1kHz
|
|
echo $CLI" FREQ 1000" | nc pc10773 5555
|
|
sleep 0.2
|
|
# width 40 us
|
|
echo $CLI" PULS:WIDT 0.000040" | nc pc10773 5555
|
|
sleep 0.2
|
|
# amplitude 0.1 V" | nc pc8830 5555
|
|
echo $CLI" VOLT 0.1" | nc pc10773 5555
|
|
sleep 0.2
|
|
# offset 0 V
|
|
#echo $CLI" VOLT:OFFS 0" | nc pc8830 5555
|
|
sleep 0.2
|
|
# VLOW 0 V
|
|
echo $CLI" VOLT:LOW 0" | nc pc10773 5555
|
|
sleep 0.2
|
|
# edge 50 ns
|
|
echo $CLI" PULS:TRAN 0.000000050" | nc pc10773 5555
|
|
sleep 0.2
|
|
# triggered burst
|
|
echo $CLI" BURS:MODE TRIG" | nc pc10773 5555
|
|
sleep 0.2
|
|
# cycles 1
|
|
echo $CLI" BURS:NCYC 1" | nc pc10773 5555
|
|
sleep 0.2
|
|
# external trigger source
|
|
echo $CLI" TRIG:SOUR EXT" | nc pc10773 5555
|
|
sleep 0.2
|
|
# delay 1 us
|
|
echo $CLI" TRIG:DEL 0.000001" | nc pc10773 5555
|
|
sleep 0.2
|
|
# slope positive
|
|
echo $CLI" TRIG:SLOP POS" | nc pc10773 5555
|
|
sleep 0.2
|
|
# turn on burst mode
|
|
echo $CLI" BURS:STAT ON" | nc pc10773 5555
|
|
sleep 0.2
|
|
|
|
|
|
echo "It is now safe to connect the cable between the amplifier board and the readout board"
|
|
echo "Please do so and press any key to continue, or press q to exit this script"
|
|
read -n 1 -s input
|
|
if [[ $input = "q" ]]; then
|
|
echo "Exiting script"
|
|
exit 1
|
|
fi
|
|
|
|
|
|
# high voltage
|
|
#sls_detector_put highvoltage 200 #because it seemed more stable, we are using external HV 230V
|
|
# output on
|
|
echo $CLI" OUTP ON" | nc pc10773 5555
|
|
sleep 0.2
|
|
|
|
echo "The current on the amplifier board should be ~0.035 A"
|
|
echo "Please check and press any key to continue, or press q to exit this script"
|
|
read -n 1 -s input
|
|
if [[ $input = "q" ]]; then
|
|
echo "Exiting script"
|
|
exit 1
|
|
fi
|
|
|
|
echo "The receiver should be waiting for data"
|
|
echo "Please check and press any key to continue, or press q to exit this script"
|
|
read -n 1 -s input
|
|
if [[ $input = "q" ]]; then
|
|
echo "Exiting script"
|
|
exit 1
|
|
fi
|
|
|
|
# sls_detector_put gainmode fixg0 # Trial for M431_JF12
|
|
# sleep 2
|
|
|
|
$RCVON &
|
|
|
|
# the scan
|
|
for ivpulse in {10..1000..10}
|
|
do
|
|
|
|
vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
|
|
echo $CLI" VOLT:HIGH "$vpulse | nc pc10773 5555 #24.02.2025 changed, before command was echo $CLI" VOLT "$vpulse | nc pc10773 5555
|
|
sleep 1
|
|
sls_detector_put start
|
|
sleep 1
|
|
done
|
|
|
|
for ivpulse in {1050..7000..50}
|
|
do
|
|
vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
|
|
echo $CLI" VOLT:HIGH "$vpulse | nc pc10773 5555 #24.02.2025 changed, before command was echo $CLI" VOLT "$vpulse | nc pc10773 5555
|
|
sleep 1
|
|
sls_detector_put start
|
|
sleep 1
|
|
done
|
|
|
|
|
|
# high voltage
|
|
#sls_detector_put highvoltage 0
|
|
# output off
|
|
echo $CLI" OUTP OFF " | nc pc10773 5555
|
|
|
|
echo "Finished scan, please wait for capacitor to discharge"
|
|
sleep 20
|
|
echo "It is now safe to disconnect the cable between the amplifier board and the readout board"
|
|
echo "Script finished"
|