#!/bin/bash

# to run do: bash CS_scan.sh

# prerequisites:
# - setup_env.sh souced 
# - the hostname is set
# - detector is on
# fileneame script has been sourced 

if [ "$1" == "" ] || [ $# -gt 1 ]; then
        echo "Parameter 1 is empty  specify G0 for normal, HG0 for HG0G1G2"
        exit 0
fi 

KILLRCV="killall ju_udp_receiver_3threads_2_0"
$KILLRCV

sls_detector_put powerchip 0
sleep 1

sls_detector_put stop

sls_detector_put powerchip 1

sleep 3

 

sls_detector_put frames 640
sls_detector_put period 0.005
sls_detector_put exptime 0.000010
sls_detector_put highvoltage 200

# configure for receiver on mpc2012
sls_detector_put udp_dstport 32410
sls_detector_put udp_dstip $DSTIP #10.1.4.105
sls_detector_put udp_dstmac $DSTMAC #3C:FD:FE:A2:14:D8 
sls_detector_put udp_srcip $SRCIP #10.1.4.9
sls_detector_put udp_srcmac 00:ab:be:cc:dd:e2

sls_detector_put readoutspeed 1
sls_detector_put start  # this puts the chip in a known state.
sls_detector_put stop




if [ "$1" == 'HG0' ]; then 
sls_detector_put settings highgain0 
#sls_detector_put reg 0x58 0x00800f ; sls_detector_put setbit 0x58 31 ; sls_detector_put clearbit 0x58 31;
echo "HG0G1G2 mode"
else
sls_detector_put settings gain0
#sls_detector_put reg 0x58 0x10800f ; sls_detector_put setbit 0x58 31 ; sls_detector_put clearbit 0x58 31;
echo "normal mode"
fi 

sls_detector_put reg 0x7f 0xff1f
#sls_detector_put reg 0x59 0x1110


#sls_detector_put reg 0x5b 0xffffffff
#sls_detector_put reg 0x5a 0xffffffff

#sls_detector_put setbit 0x58 30 ; sls_detector_put clearbit 0x58 30;#set colum select register to ffffffff, normal state, switch enabled. 

sls_detector_put gainmode dynamic


if [ "$1" == 'HG0' ]; then 
$TKCSHG0 &
else
$TKCSG0 &
fi 
sleep 2


echo "recording G0 pede" 
sls_detector_put start 
sleep 4


echo "recording G1 pede" 
sls_detector_put gainmode forceswitchg1
sls_detector_put start 
sleep 4


echo "recording G2 pede"
sls_detector_put gainmode forceswitchg2
sls_detector_put start 
sleep 4


sls_detector_put gainmode dynamic


# turn on current source
# bit 16 high bit 17 low = automatic cal col sweep 
# bit 16 high bit 17 high = cal col selected with bits 26-20

#sls_detector_put currentsource 1 nofix 0x8000000000000000 normal # this pattern was inverted, inject signals in cols 0, 63 ... 1 or 63, 0 ... 62
sls_detector_put currentsource 1 nofix 0x0000000000000001 normal #normal #low #correct pattern for JF11 and JF12
#sls_detector_put currentsource 1 nofix 0x800000ffff000003 normal # workaround, seems like too much current fir single column in JF12, also inject current to left/right columns
#sls_detector_put currentsource 1 nofix 0xffffffffffffffff normal 

sleep 1

#sls_detector_get reg 0x1D








# loop 1
for tint in {50..450..50} # 25 is too small here, 50 min
do
tint_sec=$(printf %.9f $(echo "$tint/1000000000" | bc -l))
echo "setting integration time to (s) " $tint_sec
sls_detector_put exptime $tint_sec
sls_detector_put start
sleep 4
done


# loop 2a
for tint in {50..100..5}
do
tint_sec=$(printf %.8f $(echo "$tint/100000000" | bc -l))
echo "setting integration time to (s) " $tint_sec
sls_detector_put exptime $tint_sec
sls_detector_put start
sleep 4
done


# loop 2b
for tint in {110..200..10}
do
tint_sec=$(printf %.8f $(echo "$tint/100000000" | bc -l))
echo "setting integration time to (s) " $tint_sec
sls_detector_put exptime $tint_sec
sls_detector_put start
sleep 4
done


# loop 2c
for tint in {225..450..25}
do
tint_sec=$(printf %.8f $(echo "$tint/100000000" | bc -l))
echo "setting integration time to (s) " $tint_sec
sls_detector_put exptime $tint_sec
sls_detector_put start
sleep 4
done


# loop 3a
for tint in {50..100..5}
do 
tint_sec=$(printf %.7f $(echo "$tint/10000000" | bc -l))
echo "setting integration time to (s) " $tint_sec 
sls_detector_put exptime $tint_sec
sls_detector_put start 
sleep 4
done


# loop 3b
for tint in {110..200..10}
do 
tint_sec=$(printf %.7f $(echo "$tint/10000000" | bc -l))
echo "setting integration time to (s) " $tint_sec 
sls_detector_put exptime $tint_sec
sls_detector_put start 
sleep 4
done


# loop 3c
for tint in {225..450..25}
do 
tint_sec=$(printf %.7f $(echo "$tint/10000000" | bc -l))
echo "setting integration time to (s) " $tint_sec 
sls_detector_put exptime $tint_sec
sls_detector_put start 
sleep 4
done


# loop 4a
for tint in {50..100..5}
do 
tint_sec=$(printf %.7f $(echo "$tint/1000000" | bc -l))
echo "setting integration time to (s) " $tint_sec 
sls_detector_put exptime $tint_sec
sls_detector_put start 
sleep 4
done


# loop 4b
for tint in {110..250..10}
do 
tint_sec=$(printf %.7f $(echo "$tint/1000000" | bc -l))
echo "setting integration time to (s) " $tint_sec 
sls_detector_put exptime $tint_sec
sls_detector_put start 
sleep 4
done


echo "Finished scan"
sls_detector_put exptime 0.000010
sls_detector_put period 0.002 
sls_detector_put frames 1000000
sls_detector_put currentsource 0
sls_detector_put highvoltage 0
echo "Script finished"
sleep 4
$KILLRCV