#!/bin/bash

# to run do: bash BP_scan.sh

# prerequisites:
# - setup_env.sh souced
# - the hostname is set
# - detector is on
# - Filename_creator has been run (with correct module #)
# - source pccalib.sh with pc (pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02)
# - waveform generator is on
# - amplifier board is powered and unconnected.
# - last file should be 2097184000 bytes big. 
# connect to pc10773 (RH7 machine connected to the pulser and, after klog, run the command
#  nc -k -n -v -l -p 5555 -e /bin/bash 

# last data file (000002.dat) should be 2097184000 bytes



KILLRCV="killall ju_udp_receiver_3threads_2_0"
$KILLRCV


sls_detector_put stop #just in case


sls_detector_put powerchip 1


sls_detector_put delay 0
sls_detector_put triggers 1
sls_detector_put frames 100
sls_detector_put period 0.005 
sls_detector_put exptime 0.00004 
sls_detector_put highvoltage 0

# configure for receiver on pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02
# source pccalib.sh with pc (pc-jungfrau-01/pc-jungfrau-test/pc-jungfrau-02)

sls_detector_put udp_dstport 32410
sls_detector_put udp_dstip $DSTIP #10.1.4.105
sls_detector_put udp_dstmac $DSTMAC #3C:FD:FE:A2:14:D8 
sls_detector_put udp_srcip $SRCIP #10.1.4.9
sls_detector_put udp_srcmac 00:ab:be:cc:dd:e2

#sls_detector_put configuremac 0 
sls_detector_put readoutspeed half_speed
#sls_detector_put readoutspeed full_speed

sls_detector_put gainmode dynamic

CLI=/afs/psi.ch/project/sls_det_software/serial_control_software/minidelay/minidelay

# prepare the AGILENT 33250A
echo $CLI" OUTP OFF " | nc pc10773 5555

sleep 0.2

#remember to put High-Z load! 
#Change load to Infinity
echo $CLI" OUTP:LOAD INF " | nc pc10773 5555

# Polarity normal
echo $CLI" OUTP:POL NORM" | nc pc10773 5555

# pulse
echo $CLI" FUNC PULS" | nc pc10773 5555
sleep 0.2
# frequency 1kHz
echo $CLI" FREQ 1000" | nc pc10773 5555
sleep 0.2
# width 40 us 
echo $CLI" PULS:WIDT 0.000040" | nc pc10773 5555
sleep 0.2
# amplitude 0.1 V" | nc pc10773 5555
echo $CLI" VOLT 0.1" | nc pc10773 5555
# offset 0 V echo $CLI" VOLT:OFFS 0" | nc pc8830 5555
sleep 0.2
# VLOW 0 V
echo $CLI" VOLT:LOW 0" | nc pc10773 5555
sleep 0.2
# edge 50 ns
echo $CLI" PULS:TRAN 0.000000050" | nc pc10773 5555
sleep 0.2
# triggered burst
echo $CLI" BURS:MODE TRIG" | nc pc10773 5555
sleep 0.2
# cycles 1
echo $CLI" BURS:NCYC 1" | nc pc10773 5555
sleep 0.2
# external trigger source
echo $CLI" TRIG:SOUR EXT" | nc pc10773 5555
sleep 0.2
# delay 1 us
echo $CLI" TRIG:DEL 0.000001" | nc pc10773 5555
# delay 40 us
#echo $CLI" TRIG:DEL 0.000040" | nc pc10773 5555
sleep 0.2
# slope positive
echo $CLI" TRIG:SLOP POS" | nc pc10773 5555
sleep 0.2
# turn on burst mode
echo $CLI" BURS:STAT ON" | nc pc10773 5555
sleep 0.2


if [ "$1" == 'Y' ]; then 
echo "started with Y argument, skipping manual checks"
else
echo "It is now safe to connect the cable between the amplifier board and the readout board"
echo "Please do so and press any key to continue, or press q to exit this script"
read -n 1 -s input 
if [[ $input = "q" ]]; then 
    echo "Exiting script"
    exit 1 
fi
fi


# high voltage
# sls_detector_put highvoltage 200 #because it seemed more stable, we are using external HV 230V
# output on
echo $CLI" OUTP ON" | nc pc10773 5555
sleep 0.2


if [ "$1" == 'Y' ]; then 
echo "started with Y argument, skipping manual checks"
else

echo "The current on the amplifier board should be ~0.035 A"
echo "Please check and press any key to continue, or press q to exit this script"
read -n 1 -s input 
if [[ $input = "q" ]]; then 
    echo "Exiting script"
    exit 1 
fi
fi

$TKBPG0 &


# the scan
for ivpulse in {10..1000..10}
do 

vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
echo $CLI" VOLT:HIGH "$vpulse | nc pc10773 5555
sleep 1
sls_detector_put start 
sleep 1
done

for ivpulse in {1050..6000..50}
do 
vpulse=$(printf %.3f $(echo "$ivpulse/1000" | bc -l))
echo $CLI" VOLT:HIGH "$vpulse  | nc pc10773 5555
sleep 1
sls_detector_put start 
sleep 1
done


# high voltage
# sls_detector_put highvoltage 0
# output off
echo $CLI" OUTP OFF " | nc pc10773 5555

$KILLRCV

echo "Finished scan, please wait for capacitor to discharge"
sleep 20
echo "It is now safe to disconnect the cable between the amplifier board and the readout board"
echo "Script finished"